RDS Satspeed 2 Bedienungsanleitung

SATSPEED-2 Interface / GPS-16 Receiver

KITS: K/SATSPEED2/W, K/SATSPEED2/C, K/SATSPEED2/S,

K/SATSPEED2/G, K/GPS16, K/GPS16/D9

User Instructions

Doc. No. S/DC/500-10-708 : Issue 5 - 8.10.13 Page 1 UK708500.DOC

Satspeed 2 Interface

Description

The Satspeed 2 Interface converts GPS data to radar compatible speed pulse .

The Satspeed 2 interface will accept a standard NMEA GGA and VTG message from a GPS receiver and will

convert this message to a pulse output proportional to forward speed. The pulse output is compatible with the

output of most industry standard radar speed sensors. The RS232 output from a GPS receiver can be shared

between the Satspeed 2 interface and any other equipment using the GPS ( e.g. a guidance system)

Advantages

True ‘speed over ground’ calculated from up to 12 GPS satellites

Sensor and cabling installed away from moving parts and out of vulnerable areas.

Not influenced by wheel slip, wheel size, tyre pressures or vehicle load.

Not influenced by pitch or yaw of vehicle

Not influenced by moving crops

Sensor positioning / alignment not critical

Operates with any GPS receiver that outputs NMEA messages via serial RS232 port.

Does not need differential correction but accuracy is directly related to GPS receiver quality.

Specification

Power supply 10-30V dc

Output: npn open collector pulse.

S/SR/385-2-001/004 :- 35.60Hz/ km/hr = 128.16 pulses per metre = 57.42 Hz/mile/hr.

S/SR/385-2-002 :- 36.60Hz/ km/hr = 131.78 pulses per metre = 59.00 Hz/mile/hr.

K/SATSPEED2/W : "SATSPEED 2" Kit with 3-way Weatherpack Connector

comprising:

Item Part Number Description Qty

1 S/SR/385-2-001 Satspeed 2 Assembly with Weatherpack Connector 1

2 S/BK/385-2-012 Mounting Plate 1

3 S/AC/385-2-011 Adhesive Pad 1

4 S/CBL/TIE/001 Cable Tie 25

5 F723-001 Self-Adhesive Cable Tie Base 10

6 S/DC/500-10-708 Instruction Leaflet 1

K/SATSPEED2/C : "SATSPEED 2" Kit with 4-way AMP CPC Connector

comprising:

Item Part Number Description Qty

1 S/SR/385-2-002 Satspeed 2 Assembly with AMP CPC Connector 1

2 S/BK/385-2-012 Mounting Plate 1

3 S/AC/385-2-011 Adhesive Pad 1

4 S/CBL/TIE/001 Cable Tie 25

5 F723-001 Self-Adhesive Cable Tie Base 10

6 S/DC/500-10-708 Instruction Leaflet 1

0.3m

5m 0.3m

SATSPEED-2 Interface / GPS-16 Receiver

KITS: K/SATSPEED2/W, K/SATSPEED2/C, K/SATSPEED2/S,

K/SATSPEED2/G, K/GPS16, K/GPS16/D9

User Instructions

Doc. No. S/DC/500-10-708 : Issue 5 - 8.10.13 Page 2 UK708500.DOC

K/SATSPEED2/S : "SATSPEED 2" Kit with 3-way AMP Superseal Connector

comprising:

Item Part Number Description Qty

1 S/SR/385-2-004 Satspeed 2 Assembly with 3-way AMP Superseal Connector 1

2 S/BK/385-2-012 Mounting Plate 1

3 S/AC/385-2-011 Adhesive Pad 1

4 S/CBL/TIE/001 Cable Tie 25

5 F723-001 Self-Adhesive Cable Tie Base 10

6 S/DC/500-10-708 Instruction Leaflet 1

Satspeed 2 Calibration

Check that the Speed Sensor Factor /GPS setting programmed into your instrument correspond with the

following, Output / Cal. Factor

Part Ref. Frequency

Hz km-1 hr-1

(Hz mile-1 hr-1)

pulse m-1

m pulse-1

m 2-pulse-1[2]

cm pulse-1

cm 2-pulse-1[2]

S/SR/385-2-001

S/SR/385-2-004 35.60

(57.42) 128.16 0.0078 0.0156 0.7803 1.5605

S/SR/385-2-002 [1] 36.60

(59.00) 131.78 0.0076 0.0152 0.7588 1.5177

S/SR/385-2-003 4 Hz RS232, NMEA GGA, VTG, 19200 Baud Rate, 8,n,1

[1] Alternative to DickeyJohn "iSpeed Interface" (uses the same SSF setting).

[2] If the speed reading is found to be half what it should be, the likely reason is because certain (earlier specification)

instruments require a SSF expressed as metres per 2pulses.

Satspeed 2 Operation

Limitation

This unit should not be fitted in situations where speed measurement <0.5km/hr isrequired,or there isconsistent

poor quality GPS reception.

On initial power-up, it may take up to 5 minutes depending on the reception, to output a ground speed signal.

When used on a regular basis (daily or weekly), the startup time may be 1-2 minutes.

Bear in mind also, that the ground speed signal may be temporarily lost depending on the terrain and ground

cover (e.g. under or behind trees), and that this will be more prevalent in areas with weaker reception from a

limited no. of satellites.

Operation

The unit will automatically find the baud rate and depending on GPS reception status, provide a forward speed

signal on power up.

NOTE: The forward speed reading will default to zero below 0.5km/hr.

5m 0.3m

SATSPEED-2 Interface / GPS-16 Receiver

KITS: K/SATSPEED2/W, K/SATSPEED2/C, K/SATSPEED2/S,

K/SATSPEED2/G, K/GPS16, K/GPS16/D9

User Instructions

Doc. No. S/DC/500-10-708 : Issue 5 - 8.10.13 Page 3 UK708500.DOC

Status LEDs

There are two LED’s indicating the unit’s status as follows,

PWR (Green) GPS (Red) Unit Status

Off Off No power

On Off Power but no GPS signal (No forward speed reading)

On Flash* Power + Standalone GPS (should result in forward speed reading)

On On Power + Differential GPS (optimal performance)

* Flashes @ VTG message frequency e.g. 4Hz

GPS 16

Description

The receiver is WAAS capable and is pre-configured for EGNOS - the European Geostationary Overlay System,

enabling sub-metre accuracy under ideal conditions. The receiver has a magnetic base. Mounting on a plastic

roof requires the metal base plate and self-adhesive pad included in the kit.

Specification

Physical:

Dimensions; 56mm (Diameter x 28mm (Height)

Weight: 87 g

Enclosure: High impact, Corrosion-proof, Waterproof.

Cable length: 5m

Environmental:

Temperature: Operating: -30°C to +75°C, Storage: -40°C to +85°C

Interface: NMEA, RS232, GGA, VTG

Performance:

SBAS: Supports WAAS, EGNOS

Start-up Time: 1.0sec typical (hot-start), 32.0sec typical (warm-start, cold start)

Accuracy: Autonomous: <2.5m, WAAS,EGNOS: <2m, Velocity (VTG): +/- 0.1m/s

Update Rate: 4Hz

Power Supply: 10-13V )via RS232), 63 mA

Baud Rate: 19,200

SATSPEED-2 Interface / GPS-16 Receiver

KITS: K/SATSPEED2/W, K/SATSPEED2/C, K/SATSPEED2/S,

K/SATSPEED2/G, K/GPS16, K/GPS16/D9

User Instructions

Doc. No. S/DC/500-10-708 : Issue 5 - 8.10.13 Page 4 UK708500.DOC

K/GPS16 : "GPS 16" Kit with 9-way 'D' Connector (for PSi)

comprising:

Item Part Number Description Qty

1 S/SR/385-2-003 RDS PSi GPS Receiver with 9-way 'D' Connector 1

2 S/BK/385-2-012 Mounting Plate 1

3 S/AC/385-2-011 Adhesive Pad 1

4 S/CBL/TIE/001 Cable Tie 25

5 S/FX/199-2-129 Self-Adhesive Cable Tie Base 10

6 S/DC/500-10-708 Instruction Leaflet 1

K/GPS16/D9 : "GPS 16" Kit with 9-way 'D' Connector

comprising:

Item Part Number Description Qty

1 S/SR/385-2-005 RDS ISOCAN/GCAN GPS Receiver with 9-way 'D' Connector 1

2 K/9WD/PLUG/LD Serial 9way 'D' Plug Lead 1

3 S/BK/385-2-012 Mounting Plate 1

4 S/AC/385-2-011 Adhesive Pad 1

5 S/CBL/TIE/001 Cable Tie 25

6 S/FX/199-2-129 Self-Adhesive Cable Tie Base 10

7 S/DC/500-10-708 Instruction Leaflet 1

8 S/DC/500-10-637 Antenna Configuration Label 1

# Wire Colour Function:-

S/SR/385-2-005 Function :-

S/SR/385-2-003

1 - - -

2 White DATA Tx -

3 Turquoise DATA Rx DATA Rx

4 White - DATA Tx

5 Black 0V -

6 - - -

7 Red - +V

8 Black - 0V

9 Red +V -

PLUG

SOCKET

SATSPEED-2 Interface / GPS-16 Receiver

KITS: K/SATSPEED2/W, K/SATSPEED2/C, K/SATSPEED2/S,

K/SATSPEED2/G, K/GPS16, K/GPS16/D9

User Instructions

Doc. No. S/DC/500-10-708 : Issue 5 - 8.10.13 Page 5 UK708500.DOC

General Installation Guidelines for the GPS Receiver

The GPS receiver has a magnetic base. A double-side adhesive foam pad and metal mounting plate isprovided in

the kit, to enable magnetic mounting onto non-magnetic surfaces.

Mount the antenna to give an unobstructed hemisphere of sky. This will ensure that GPS satellites are not

masked by parts of the vehicle, potentially reducing system performance.

Wherever possible, avoid drilling holes in the roof to avoid both water ingress and possibly wiring / air

conditioning equipment etc. If drilling is unavoidable, use silicone sealant around fixing and cable entry points.

Mount the antenna as far as possible from any equipment that can cause Electromagnetic Interference

(EMI)including DC motors (e.g. air conditioner), alternator, solenoids, CB radio, power cables, display units, or

other electronics. Excessive EMI will degrade system performance.

TIP: To detect possibly troublesome interference, tune a LW band portable radio off-station. With the aerial laid flat you

can then (hopefully) pick up the direction and source of the interference from the increase in noise. The antenna

can then be repositioned or if necessary, the source of the interference suppressed. If need be, contact RDS for

further advice on suppression methods.

Secure the antenna cable close to the antenna mounting (using cable ties) so that in the event the antenna is

knocked off it's magnetic mounting, it will be restrained and minimise the possibility of further damage.

Mount the antenna in the location for which you desire a position e.g. along the centre line of the vehicle and

as close as possible over the working interface.

NOTE: As this may well be impractical to achieve, the Pro-Series can be programmed via the ‘GENERAL PF SETUP‘

menu with ‘GPS ANTENNA OFFSETS’ to compensate for the difference in position of the antenna from the cutter

bar, spray boom etc (please refer to the "PSi PF Instruments Data Logging and Transfer" manual).

GPS 16 Setup (Standalone GPS input to PSi)

Connect the receiver to the top port on the PSi.

From the "SETUP" menu, select "Port Setup" and set the top port to "GPS Only".

From the "SETUP" menu, select the Speed Sensor Setup screen ( ), and select "NMEA VTG".

From the "General PF Setup" menu, select "GPS Baudrate" and select "19200".

After the initial power-on, allow up to 5 minutes for the receiver to automatically establish its position.

Subsequently the unit should establish position more quickly.

NOTE: The GPS icon at the top of the display indicates the status of the GPS signal.

GPS 16 Setup (Standalone GPS input to ISOCAN)

Please refer to the appropriate installation manual supplied with the product.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere RDS Aufnahmegeräte Handbücher

RDS

RDS Satspeed Gebrauchs- und Pflegehandbuch

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch