Ready Rack FH2G Bedienungsanleitung
FH2G EXPRESS 2 GEAR DRYER
INSTALLATION, OPERATION AND MAINTENANCE MANUAL
REVISION 1 • 2019
www.ReadyRack.com
(800)-991-2120
FH2G –Express Dryer
Installation, Operation and Maintenance Manual
1 | P a g e
Features of the 2 Gear Dryer Cabinet
•Simple to use, NFPA 1851 compliant controls.
•Rugged and durable galvanized steel components.
•Drying with ambient or heat air, up to 1500W of heating capacity.
•Three heavy duty slide out galvanized wire racks, with adjustable positions.
•Capable of vented and unvented operation.
Unpacking the Express Dryer –FH2G (Two Gear)
•Remove shipping crate sides and set aside, taking care not to damage dryer when
removing steel corners.
•Carefully inspect dryer for shipping damages prior to proceeding.
•Open cabinet and remove shelves and hangers.
•Remove ¼-20 lag bolts and washers connecting cabinet to pallet.
•Carefully remove the dryer from the pallet and locate near installation area.
FH2G –Express Dryer
Installation, Operation and Maintenance Manual
2 | P a g e
Figure –Uncrating Dryer
Selecting a Location
•The two-station dryer should not be located in basements, outdoors or unheated
rooms. If adequate air circulation in the space is not available, the unit should be
converted to ducted operation. Placement in unvented or sub-grade internal rooms
with limited air movement can create mold or mildew conditions.
•The drying cabinet can be located within 1-2” of a wall, provided that 10-12” of
clearance is available on the sides to open the door fully.
•Position the dryer on a level floor.
FH2G –Express Dryer
Installation, Operation and Maintenance Manual
3 | P a g e
Levelling the Dryer
•The dryer is provided with (4) adjustable feet. These feet can be adjusted using a
standard adjustable wrench. If the foot retaining nut or top nut have loosened, they can
be re-secured using a 15/16” wrench and 15/16” deep socket.
•The cabinet will “twist” during levelling. Confirm the proper alignment of the door in the
frame during levelling. The door should not bind or swing on its own when the cabinet is
properly levelled.
•Door alignment will vary from the pallet to the floor and small adjustments in the feet
will effect the final level of the door.
Understanding the Model Number
The drying cabinet is shipped pre-configured for the expected power supply. Look for the
placard inside the door of the cabinet to determine the configuration of the cabinet.
Figure: Electrical Placard
It is important to correctly match the power supply to cabinet specifications otherwise damage
or injury may result.
FH2G –Express Dryer
Installation, Operation and Maintenance Manual
4 | P a g e
RR-120-1 →120V / 1 PH / 60 hZ
The FH2G dryer is not configurable as a 208 or 240 supplied unit. For 208 or 240 applications
contact Ready Rack for information on FH6G, models RR2401, RR2083 or RR2081 units.
Wiring
•The two gear dryer is shipped with a standard 120V, 3 prong grounded plug. This can be
utilized with any 15A circuit.
•If required, the cabinet can be permanently wired into a station power supply by the
following steps by a licenced electrician:
oRemove rear access panel (4 x #12 hex self tapping screws).
oDisconnect 12/3 cable from din rail terminal block and release from strain relief.
oReconnect electrical supply, with a recommended 20A supply for permanent
supply.
oReconnect rear cover.
Figure –Rear Access and Strain Relief
Figure –Rear Terminal Block
FH2G –Express Dryer
Installation, Operation and Maintenance Manual
5 | P a g e
Converting the Dryer to external Ducting:
Drying cabinets work best when the moisture laden air is moved away from the vicinity of the unit. This
can be through an external wall or into a larger apparatus bay with suitable air make-up or
dehumidification.
•The unit is provided with a galvanized fan cover for un-ducted applications.
•Lock-out the unit or unplug from the power supply.
•Remove the (4) #12 self tapping screws and take the cover off the unit dryer
roof.
•The venturi outlet for the fan is 12 3/8” diameter. A standard 14” to 12” or 14”
to 10” collar transition may be used. The collar should be fixed vertically into the
roof of the cabinet, avoiding the fan blade inside the cabinet.
Figure –Top Duct Guard
FH2G –Express Dryer
Installation, Operation and Maintenance Manual
6 | P a g e
Figure –Top Duct Guard
•The diameter of the ducted tube should not be restricted less than 10” in diameter.
•Runs longer than 10’ may require the use of a booster fan (not included) to ensure
pressure losses are overcome.
•An external self-closing louvre should be utilized to keep out pests and rain water.
•The use of legacy “square or rectangle” ducting is permitted, considering a minimum
dimension of 8” x 16”.
OPERATING THE DRYING CABINET
FIGURE: CONTROL PANEL
STEP ONE
•Load gear or hose into the dryer.
•Close door(s) and secure latch.
FH2G –Express Dryer
Installation, Operation and Maintenance Manual
7 | P a g e
STEP TWO
•Hold MODE/SELECT for up to 5 seconds to turn on panel. ON ENABLE light will turn
Green.
•Press MODE/SELECT once to turn FAN ON ONLY. FAN ON ONLY light will turn Yellow.
•Press MODE/SELECT once more to turn FAN & HEATER ON. FAN & HEATER light will turn
Red.
•Pressing one final time will turn panel OFF.
STEP THREE
•Select the desired equipment to be dried.
oHOSE comes with a pre-set time of 10 Hours
oGEAR comes with a pre-set time of 3 Hours
STEP FOUR
•Adjust time (if necessary) by pressing HOURS or MIN button.
•Use ARROW UP or ARROW DOWN to adjust time.
STEP FIVE
•Start drying by pressing START/STOP BUTTON.
•Unit will automatically turn off at end of cycle.
MAINTAINING DUTY GEAR
Your new drying cabinet is a key part in meeting the NFPA 1851: Standard on Selection Care
and Maintenance of Structural Firefighting Protective Ensembles.
Proper drying is critical for the maintenance and longevity and safety of duty gear. By properly
preparing and utilizing the Firehouse Express Dryer, it is possible to return gear to service
quicker and in better condition than other methods.
Preparation:
•Ensure that the gear has been properly cleaned of all contaminants through the proper
selection and use of detergent and PPE washing systems. Contact Ready Rack for more
information regarding total cleaning cycle products.
FH2G –Express Dryer
Installation, Operation and Maintenance Manual
8 | P a g e
•Boots, gloves and hoods can be placed on either hangers or directly on the mesh
shelving units. Ensure each item is straightened and not twisted.
•For simple drying activities where the gear has not been soaked or rinsed, pants, jackets
and liners can be hung as a set. The Firehouse Express dryer will process the equipment
as-is. Examples of this can include non-hazardous response calls where simple sweat or
humidity is introduced to the gear. Allowing moisture to remain can cause steam burns
should a rapid heat up of the gear occur.
•Where equipment is very wet or has been separated for mechanical washing, hang the
paints and jackets, with the liners separate. For single or double sets of gear, separating
will reduce the overall cycle time to complete drying.
Drying:
Proper drying relies on a number of conditions, many of which are under the users control. The dryer
controls will ensure that the equipment is not overheated, the operator can choose to use ambient or
heated air depending on the conditions within the firehouse.
•Ensure the gear is organized in the cabinet when loading.
•Check that the doors(s) are correctly closed and the seals are in good working condition.
•Balance the amount of gear to be dried to the conditions. A warm humid station will take longer
to dry than a dry station.
•Using a proper extractor will require less moisture to be removed by the cabinet.
FH2G –Express Dryer
Installation, Operation and Maintenance Manual
9 | P a g e
Post-Drying:
•Ensuring that the gear is properly stored is important to maintaining clean and dry and
protected. Utilizing a duty gear hanger or locker will ensure the gear is protected from dirt and
debris, as well as preventing mildew build-up.
MONTHLY INSPECTION
•Clean and remove all debris and dust from inside the cabinet. Remove plenum from floor and
clean underneath.
•Check for missing screws or guards.
•Check unit for level and adjust feet as necessary.
•Check the shelves and sliders for burrs and wear. Check that the sliders are secure.
•Check all hanging rails supports for security.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Ready Rack Trockner Handbücher
Beliebte Trockner Handbücher anderer Marken
Indesit
Indesit IDV 75 Bedienungsanleitung
Infiniton
Infiniton SD-DG85C Bedienungsanleitung
BOMANN
BOMANN WT 5019 Bedienungsanleitung
Alliance Laundry Systems
Alliance Laundry Systems TMB795C Bedienungsanleitung
Asko
Asko T793C Bedienungsanleitung
Kenmore
Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung