ReadyNet AC1200MS Bedienungsanleitung

Home

PBXware

SERVERware

TELCOware

SIPmon

SIPProt

Desktop & Mobile

BRM

UADs

Appliances

EOL

From Bicom Systems Wiki

Contents

1 Introduction - How to use ReadyNet AC1200MS with PBXware

■

1.1 Requirements

■

2 Installation

■

2.1 Power Adapter

■

2.2 IP Address

■

2.3 Factory Settings

■

3 Registering Device

■

3.1 Manual Configuration

■

3.2 Auto Provisioning

■

Introduction - How to use ReadyNet

AC1200MS with PBXware

This "How to" is written as a general guide on how to use your ReadyNet AC1200MS with

PBXware 5.3.1.0. It covers the most common tasks required in order to have your ReadyNet

AC1200MS working efficiently.

Requirements

1. Identify ReadyNet device

To start and successfully complete registration of your ReadyNet device you need to know

■

which device model you will setup.

From the back of each ReadyNet device there are exact model information that you should

■

check. Although different device models can have exactly the same requirements and

installation procedure, device models can also have significantly different requirements and

installation procedure, so that ignorance of your own model may result in the inability to

successfully set up your device.

2. ReadyNet AC1200MS firmware.

- Make sure that device is loaded with 3.20 firmware.

3. DHCP server.

- Fully configured and operational DHCP server.

Installation

This chapter describes how to install and connect the device to the electrical power and data

network as well as how to apply factory settings.

The following topics are covered:

- Power adapter

- Factory Settings

Power Adapter

1. Connect the Network and Power

Connect the DC plug on the power adapter to the DC port on the device and connect the other

■

end of the power adapter into an electrical power outlet.

Connect the ethernet cable between the Internet port on the device and the network port on a

■

router or switch to access LAN.

IP Address

1. Find out your ReadyNet AC1200MS IP Address

For ReadyNet AC1200MS lift the handset and enter ****, choose "1" and then choose "2", the

■

IP address will be recited.

Factory Settings

1. Reset to factory settings

This step is not required for out-of-the-box devices, however, if the device has been already used

then it is a must.

For ReadyNet AC1200MS press the reset button at the front of your router for 10 seconds, this

■

will wipe out any changes made to your router.

Device will be reset to the factory default settings.

Wait sometime prior for device to reboot.

■

NOTE: Do not unplug or remove power to the device while it is updating firmware and

configurations.

Registering Device

This chapter describes how to identify ReadyNet AC1200MS device model, requirements that

must be met and how to register the device using manual configuration or auto provisioning.

The following topics are covered:

- Manual Configuration

- Auto Provisioning

Manual Configuration

This chapter describes how to set UAD settings, create PBXware extension and register the

device.

The following topics are covered:

- UAD Settings

- Creating Extension

- Registering Device

UAD Settings

1. Login to PBXware web administration interface

Open a new browser window and enter the IP address in order to access the PBXware web

■

administration login screen. Example: http://192.168.1.10

■

2. UAD settings

Navigate to Settings:UAD.

■

Make sure ReadyNet AC1200MS UAD is enabled. To check the UAD status click on the edit

■

icon corresponding to your ReadyNet AC1200MS UAD phone.

Make sure Status is set to Active, Auto provisioning is set to No, and DHCP is set to Yes.

■

UAD settings

Click on the Save button to save changes.

■

Creating Extension

1. Add Extension

Navigate to Extensions. Click on Add Extension.

■

The standard options window will be shown below.

■

Select ReadyNet device model from the UAD select box.

■

Select Location: Local or Remote.

■

Local is for all extensions registered on the LAN and Remote is for all extensions

registered from remote networks, WAN, Internet etc.

Click on the Next step button.

■

2. Extension values

Enter values into the required field text boxes.

REQUIRED FIELDS:

Name

■

Enter a name for the extension being created. Example: John Smith.

E-mail

■

Enter the e-mail address associated with this extension. This e-mail address will receive all

system notification messages. Example: [email protected]

Creating Extension

Click on the Save button.

■

Optionally, click on the Save & E-mail button. Account details will be sent to the e-mail

■

address associated with this extension.

OPTIONAL FIELDS

Extension

■

An auto-generated extension number based on the next available sequential number. An

extension value can be changed. Example: 1003.

Secret

■

A secret value associated with the UAD is auto-generated in order to allow the UAD to

successfully register with the system. The secret value can be changed, however it is

STRONGLY recommended not to change the system generated value to a simple value like

"1234" or "1003" etc.

■

An auto-generated PIN will allow access to voicemail and online self-care.

Registering Phone

This chapter describes how to register ReadyNet AC1200MS device using Hostname or IP

Address.

Hostname or IP Address

1. Login to device web administration interface

Open a new browser window and enter your phone IP address in order to access the device

■

web administration interface login screen. Example: http://192.168.1.22.

■

factory default login details are username: admin and password: pz938q12ms.

Click on FXS1 tab at the top navigation menu.

■

Enter the following details into the respective fields.

■

REQUIRED FIELDS:

Proxy Server (Proxy and Registration section)

■

Enter the Hostname or IP Address of the PBXware.

- Example for Hostname: voip.bicomsystems.com

- Example for IP Address: 192.168.1.10

Display name (Subscriber Information section)

■

PBXware extension name. Example: John Smith.

Account (Subscriber Information section)

■

PBXware extension number. Example: 1003.

Phone Number (Subscriber Information section)

■

PBXware extension number. Example: 1003.

Password

■

The Secret of the extension as received in the e-mail associated with this extension.

Example: _%Z4M3*Ts9y7. A password is generated automatically for each newly created

extension.

Click on the Save & Apply button.

■

If everything is done as above described, you should have successfully registered your device

■

to PBXware. Dial *123 to verify registration.

Auto Provisioning

This chapter describes how to set UAD settings, create PBXware extension and register the

device using DHCP or Static IP address.

The following topics are covered:

- UAD Settings

- Creating Extension

- Registering Device

UAD Settings

1. Login to PBXware web administration interface

Open a new browser window and enter the IP address in order to access the PBXware web

■

administration login screen. Example: http://192.168.1.10.

■

2. UAD settings

Navigate to Settings:UAD.

■

Make sure ReadyNet AC1200MS UAD is enabled. To check the UAD status click on the edit

■

icon corresponding to your ReadyNet AC1200MS phone.

Make sure Status is set to Active, Auto provisioning is set to Yes, and DHCP is set to Yes.

■

UAD settings

Click on the Save button to save changes.

■

Creating Extension

1. Add Extension

Navigate to Extensions. Click on Add Extension.

■

The standard options window will be shown below.

■

Select ReadyNet AC1200MS device model from the UAD select box.

■

Select Location: Local or Remote.

■

Local is for all extensions registered on the LAN and Remote is for all extensions

registered from remote networks, WAN, Internet etc.

Click on the Next step button.

■

2. Extension values

Enter values into the required field text boxes.

REQUIRED FIELDS:

Name

■

Enter a name for the extension being created. Example: John Smith.

E-mail

■

Enter the e-mail address associated with this extension. This e-mail address will receive all

system notification messages. Example: [email protected]

Auto Provisioning

■

Set to Yes.

MAC Address

■

Enter ReadyNet AC1200MS device MAC address. Example: 0002FDFF1536. MAC

address can be found at the back of the phone.

Creating Extension

Click on the Save button.

■

Registering Phone

This chapter describes how to register ReadyNet AC1200MS device using DHCP or TFTP.

The following topics are covered:

- DHCP

- TFTP

DHCP

1. Configure DHCP

Make sure your DHCP router is configured to use option 66 to automatically instruct devices

■

with the URL for auto provisioning. For more information refer to your router documentation

or contact your network administrator.

2. Device first boot or user initiated reboot

Auto provisioning process will start during device first boot or after reboot process has been

initiated by user. DHCP server will instruct the device where from to pickup appropriate

configuration file. If everything is done as above described, you should have successfully

registered your device to PBXware.

TFTP

1. Login to device web administration interface

If there is no DHCP in your network, you can still auto provision your ReadyNet AC1200MS

device. Please refer to your ReadyNet AC1200MS phone device User Guide for instruction about

setting static IP address. After you configure your ReadyNet device to use a static IP address,

continue with the following steps.

Open a new browser window and enter your device IP address in order to access the device

■

web administration interface login screen. Example: http://192.168.1.22

■

note, factory default login details are username: admin and password: pz938q12ms.

Click on Administration tab at the top navigation menu.

■

Click on Provision tab.

■

In the Profile Rule field enter tftp:// followed by Hostname or IP Address, followed then by

■

/$MA.conf.

- Example for Hostname: tftp://voip.bicomsystems.com/$MA.conf

- Example for IP Address: tftp://192.168.1.10/$MA.conf

Make sure that Option 66 is DISABLED.

■

Click on the Save & Apply button.

■

Click on the Reboot button.

■

If everything is done as above described, you should have successfully registered your device

■

to PBXware. Dial *123 to verify registration.

Retrieved from "http://wiki.bicomsystems.com/ReadyNet_AC1200MS"

Disclaimers - About Bicom Systems Wiki

Andere Handbücher für AC1200MS

Inhaltsverzeichnis

Andere ReadyNet WLAN-Router Handbücher

ReadyNet

ReadyNet LTE520 Bedienungsanleitung

ReadyNet

ReadyNet WRT-500 Bedienungsanleitung

ReadyNet

ReadyNet LTE520 Bedienungsanleitung

ReadyNet

ReadyNet LTE500 Bedienungsanleitung

ReadyNet

ReadyNet WRT150N Bedienungsanleitung

ReadyNet

ReadyNet AC1100MSF Bedienungsanleitung

ReadyNet

ReadyNet WR300NQ Bedienungsanleitung

ReadyNet

ReadyNet WRT-500 Bedienungsanleitung

ReadyNet

ReadyNet AC1200M Bedienungsanleitung

ReadyNet

ReadyNet AC1000M Bedienungsanleitung

ReadyNet

ReadyNet AC1300MS Bedienungsanleitung

ReadyNet

ReadyNet WR300NQ Bedienungsanleitung

ReadyNet

ReadyNet WRT300N-D6 Bedienungsanleitung

ReadyNet

ReadyNet wrt300n-rn Bedienungsanleitung

ReadyNet

ReadyNet QX300 Installations- und Benutzerhandbuch

ReadyNet

ReadyNet LTE520 Bedienungsanleitung

ReadyNet

ReadyNet WRT300N-DD Bedienungsanleitung

Beliebte WLAN-Router Handbücher anderer Marken

Milesight

Milesight UG67 Bedienungsanleitung

Airlogic

Airlogic AirSync Class 1 Betriebsanleitung

Samsung

Samsung WCH730B Bedienungsanleitung

TELEFONICA

TELEFONICA USB Adapter Bedienungsanleitung

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Bedienungsanleitung

Askey

Askey RAC2V1K Bedienungsanleitung

Alloy

Alloy WLF2454AP-S Bedienungsanleitung

TP-Link

TP-Link TL-WR542G Bedienungsanleitung

NETGEAR

NETGEAR WNR2000v4 Bedienungsanleitung

Hama

Hama 53120 Bedienungsanleitung

Intellinet

Intellinet 524582 Bedienungsanleitung

Asus

Asus RT-N10P Bedienungsanleitung

D-Link

D-Link DIR-506L Bedienungsanleitung

Sapido

Sapido GR297n Bedienungsanleitung

Asus

Asus DSL-N55U Bedienungsanleitung

AMTC

AMTC WR7502 Bedienungsanleitung

Compaq

Compaq CP-2W - iPAQ Connection Point Bedienungsanleitung

SMC Networks

SMC Networks WBR14-N2 FICHE Bedienungsanleitung