Reboot ARC145 Bedienungsanleitung

Version Number: ARC145-20210106A1

Operation Manual

Reboot ARC145 is an intelligent and easy-to-operate welding machine with manual welding mode. It has the

characteristics of good welding performance, diversified usage scenarios, and outstanding welding effects. It is highly

praised by welding enthusiasts and is also very good for beginners in welding. Friendly and can get started quickly.

Part 1: Machine Introduction

1. Power indicator light

Turn on the power, this light will be on.

2. Current display meter

Only displays the preset current.

3. Fault light

When the welding load is overloaded and the output current of the machine is too large, this light will be on. This situation is

normal and the machine can be restored; when there is damage inside the machine, this light will be on. In this case, the machine

is abnormal and requires maintenance.

4. The current adjustment knob

Just adjusts the current.

5. Positive connection

Install welding holder and grounding clamp.

6. Negative connection

Install welding holder and grounding clamp.

Note: ARC145 AC 110V OR AC 220V voltage input

Part 2: Introduction to the product and configuration list.

Version Number: ARC145-20210106A1

No.

Picture

Name

Qty

Remark

ARC145

Please check the appearance after

receiving the machine, and power on to

check

Welding

holder

1.5m 16MM2 cable, 200A Italian welding

holder +15-25mm2 European quick plug

Ground

clamp

1.5m 16MM2 cable, 300A Ground clamp

+10-25mm2 European quick plug

Hammer

and brush

Conversion

line

Conversion line only suit for 220V to

110V dual-voltage input machines, if not

dual- voltage machines no this line

included.

Manual

Normally provides manuals in English, if

you need other language like French,

German, Italian, Spanish, and Russian

please contact us to get electronic

version documents .

Warranty

Card

If you have more questions for

consultation, please contact us through

the after-sales mailbox on the card.

Part 3: Simple test for powering on the machine

Reboot ARC145 welding machine will undergo strict various tests when it leaves the factory to ensure that

every welding machine that reaches the user is of high quality, because our machine has to go through tens of

thousands of kilometers of long-distance transportation from the factory to the delivery to you. And many times of

Version Number: ARC145-20210106A1

handling, it is inevitable that some uncontrollable factors will cause some internal components of the machine to

become loose or even damaged during the process. We recommend that you perform a power-on inspection as soon

as you get the welding machine to ensure that what you receive is qualified product.

Precautions for power-on inspection:

1、 Please make sure your power supply voltage is 110V+-15% or 220+-15%. REBOOT ARC145D supports 110V

and 220V input voltage in North America and Japan, and REBOOT ARC145 supports 220V input voltage in the

UK, EU and other regions; if you have a generator power supply, please ensure that the generator is not less than

4000w.

2、It is recommended to choose 50A circuit breaker protection when your power supply voltage is 110V, and 30A

circuit breaker protection when 220V.

3、 For the current machine, please choose the power plug that suits your local electrical law requirements

4、 Extension cord: #12 AWG or larger; 25’ (8m) or shorter.

Turn on the power switch of the machine and the fan on the back of the machine rotates, and the digital

display on the panel indicates that the power is normal.

Note:

1) In order to reduce the working temperature of the machine, it is normal for the fan to continue to rotate for a

few seconds after the power is turned off.

Version Number: ARC145-20210106A1

2) In the process of high-strength continuous welding, machine protection may occur, and the OC light on the

machine panel will be on. After continuous heat dissipation, the machine will return to normal, which is normal.

3) During the welding process, if you feel that the welding is not good, the spatter is too large, or the arc is

broken, please exchange the connection of the welding clamp and the grounding clamp with the machine.

Attached table: Self-examination of abnormal conditions without response when turning on the machine:

1. The machine's power switch is not turned on.

2. The power input voltage is wrong.

Version Number: ARC145-20210106A1

3. The power plug is loose.

4. The internal circuit is loose (due to long-distance transportation, bumps), you need to open the cover and

check the internal connection line.

Part 4: Technical specifications

TYPE

ARC145

ARC145D

Input power voltage (V)

1phase AC220V±15%，50/60Hz

1phase AC110V/220V±15%，50/60Hz

Rated input current (A)

29.1

44/29.1

Rated power capacity (KVA)

6.4

Current adjustment range (A)

30-145

30-115/30-145

Welding thickness (mm)

>1.0

Voltage adjustment range (V)

23.2-25.6

No-load voltage (V)

56±5

Rated duty cycle

60%

Efficiency (%)

80%

Power factor

0.7

Protection class

IP21S

Insulation class

Size (mm)

300*290*330

Weight (Kg)

3.85

Part 5: Machine operation guidance.

If you want to repair some broken fences or fix brackets, you like to use traditional welding rods for operation,

you can use REBOOT ARC145.

1、Connect welding holder and ground clamp.

Version Number: ARC145-20210106A1

2、 To adjust the current, only the current can be adjusted.

Note:

1） The welding rod specification supported by REBOOT ARC145 is below 4.0(5/32in), usually 2.5(3/32in) and

3.2(1/8in). European style generally uses E6013, American style generally uses E7018，and stainless steel

generally uses ER308.

2） It supports welding of 1-8mm(1/64-5/64in) carbon steel and 1-5mm(1/64-7/32in) stainless steel. Aluminum can

not be welded. For carbon steel, please use carbon steel electrode. For stainless steel, please use stainless steel

electrode.

Version Number: ARC145-20210106A1

3） Connect the ground clamp to clean bare metal. No rust, paint or other coatings, and ensure good electrical

conductivity.

4） The ideal distance between the welding rod and the welding object is 1-2mm(1/64-5/64in), to ensure that the

welding rod and the workpiece are in continuous and stable contact. The welding rod should not be too high or

pressed too low to avoid arc breaking and adhesion.

5） It is normal for novices to have adhesion during the welding process, and you can try to friction arc to avoid

adhesion.

6） Suitable for ordinary welding rods, such as 7018, 6013, etc., but not suitable for special welding rods, such as

7010, 7011.

Possible problems

1) There is no arc, check the ground wire to connect the workpiece to ensure that there is no rust, paint or other

coatings on the workpiece.

2) There is no arc, check the direct distance between the welding rod and the welding object, the ideal distance

is 1-2 mm; check whether the welding object has rust or oil stains, it is recommended to polish with sandpaper

or a grinder.

3) During the welding process, the oc fault light is on, and it may be over-current protection. You need to stop

working for a few minutes, let the machine cool for a period of time, and automatically recover. If the air cools

for more than 10 minutes, the machine does not automatically recover, please shut down and restart.

4) The OC light is on when the machine is turned on, please contact us.

5) If you have any problems that cannot be solved, please contact us at service@mirthtek.com .

Part 6: Internal diagram of the machine

Version Number: ARC145-20210106A1

1. The EMC board is used to isolate the external power grid and internal circuits of the machine to avoid mutual

interference.

2. All-copper main transformer, big power.

3. 3 high-power large capacitors, the machine is more stable.

4. Thicker radiator for better heat dissipation.

5. 4 imported IGBT, stable and powerful current output.

6. 3 imported rectifier tubes, stable and powerful current output.

Version Number: ARC145-20210106A1

Part 7:Trouble Shooting

PROBLEMS(SYMPTOMS)

POSSIBLE CAUSE

PROBLEMS IN STICK WELDING

Excessive spatter

1. Long arc.

2. High current.

Craters

1. Fast movement of the electrode away from piece.

Inclusions

1. Poor cleanliness or distribution of the Welding passes.

2. Improper movement of the electrode.

Insufficient penetration

1. High progression speed.

2. Welding current too low.

3. Narrow chamfering.

Sticking

1. Arc too short.

2. Current too low.

Porosity

1. Humidity in electrode.

2. Long arc.

Cracks

1. Current too high.

2. Dirty materials.

3. Hydrogen in weld (present on electrode coating).

ELECTRICAL FAILURES

Machine fails to come on

(Power LED off)

1. No Input Voltage.

2. Faulty supply plug or cable.

3. Internal fuse tripped. Allow time to Auto reset.

Thermal overload (Thermal LED on)

1. Unit has been operated beyond its capacity rating.

2. Airflow through machine is restrict- ed or fan has failed.

Part 8: Welding parameter settings

Welding thickness（㎜）

4-5

Electrode diameter（ф㎜）

3.2

3.2-4

Welding current（A）

40-65

50-80

100-130

If you are interested in translating professional local languages, please contact us at

[email protected], we can pay for it.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Reboot Schweißsystem Handbücher

Reboot

Reboot RBT-200PD/ACDC Bedienungsanleitung

Reboot

Reboot RBM2100 Bedienungsanleitung

Reboot

Reboot RBM-2100D Bedienungsanleitung

Reboot

Reboot CUT40 Bedienungsanleitung

Reboot

Reboot RBM2000P Bedienungsanleitung

Reboot

Reboot RBM-1550 Bedienungsanleitung

Reboot

Reboot RBM1600 Bedienungsanleitung

Reboot

Reboot RBM1350 Bedienungsanleitung

Reboot

Reboot RBA1400 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung