Recom RBB10-2.0-EVM-1 Bedienungsanleitung

www.recom-power.com REV.: 1/2019 P-1

RBB10-2.0-EVM-1

Evaluation Module

Features

Evaluation

Module

• Evaluation platform for RBB10 buck/boost regulators

• Input voltage can be lower, higher or the same

as output voltage

• Class B EMC ﬁlter layout

• Built-in thermal management

• Easy evaluation of modes, trimming, enable and

sensing fufnction of the RBB10 modules

Description

The RBB10-2.0-EVM-1 evaluation board generates a regulated output voltage with a current up to

4A from an external DC supply which can be higher, lower or the same as the set output voltage.

The output voltage is preset to 3.3V or 5V but can be adjusted between 1.0V and 5.5V using on-board

resistors. All of the functions of the RBB10-2.0 regulator such as the different operating modes, output

trim, enable, and the sense input can be easily evaluated using the break out connectors.

Typical applications that can be evaluated include:

USB voltage converter/regenerator: 3.3V or 5V output from a 3.3V (+60%/-30%) or from a

5V (+10%/-50%) supply. A stable output voltage can be regenerated even if the input voltage is outside

of the USB voltage speciﬁcation.

With a regulated supply voltage, the following continuous output current limits apply:

Selection Guide

Part Input Output Output

Number Voltage Range Voltage Current

[VDC] [VDC] [A]

RBB10-2.0-EVM-1 2.3 - 5.5 1.0 - 5.5 2.0

(5VDC preset) (4.0 buck mode)

Caution:

ESD sensitive. Always follow ESD preventative procedures when

handling the product!

Battery stabiliser: the output can be set to deliver a stable 5V or 3.3V from a nominal 3V, 3.7V or

4.2V Lithium Ion or 3V/4.5V alkaline battery pack. In standby, the board consumes only 5µA.

Supercapacitor booster: the output can be set to deliver a stable 5V or 3.3V from a single

supercapacitor (2.3V – 2.7V) or from two supercapacitors wired in series (2.3V – 5.4V).

Low voltage regulator with sense: 1V, 1.2V, 1.8V or 2.5V output with up to 4A current.

nom. Input

Voltage (1)

Output

Voltage

Output

Current

3.3V 1.8V 4A max

3.3V 3.3V 2.8A max

3.3V 5V 2.2A max

5V 1.8V 4A max

5V 3.3V 4A max

5V 5V 3.2A max

Notes:

Note1: For detail information please refer to “Safe Operating Area” graph on page P-2

www.recom-power.com REV.: 1/2019 P-2

Evaluation Module

Speciﬁcations (measured @ Ta= 25°C, full load after warm up unless otherwise stated)

RBB10-2.0-EVM-1

Quick Start Guide

1) Connect Sense to the required potential.

The Sense input is via R3 directly at the power module output. To compensate for ohmic losses of the ﬁlter, desolder the R3 resistor

and move it to the position of R4.

If you want to sense directly on the load, desolder R3 and connect the middle pin of Con 2 to the positive potential of the load with a

separate connection.

2) If a different output voltage is required, ﬁt R5 or R6.

3) Connect Con1 to a DC power supply and check output voltage.

4) Connect Con2 to the load.

5) Enable the device on Con3.

The converter is normally on. You can disable the converter by pulling the Enable pin to GND with a switch, open collector driver or logic

input. R1 or R2 can be used to change the default function from normally on to normally off.

6) Modes:

The RBB10-2.0 has the possibility to work in two regulation modes:

6.1) Powersave Mode (standard)

This mode is the best for use at low loads to reduce power consumption and extend battery life. In this mode the internal power

consumption is reduced by using burst mode for loads under 350mA and PWM for loads above 350mA. The drawback is a 1-3 %

higher output voltage at low load than full load.

6.2) Fixed PWM mode

In PWM mode the device accurately regulates the output voltage independently of the load current. The drawback is a higher

internal power consumption and shorter battery life at lower loads. Pull down the Mode pin on Con4 to GND or solder a 0Ω

resistor a position R7 to enter this mode.

4.5

4.0

3.0

2.0

3.5

2.5

1.5

1.0

0.5

Output Current [A]

Input Voltage [VDC]

2.3 2.7 3.1

3.3 3.6 5.0

3.5 3.9 4.3 4.7 5.1 5.5

5.5Vout

5.0Vout

3.3Vout

1.0Vout

Safe Operating Area

www.recom-power.com REV.: 1/2019 P-3

Evaluation Module

Speciﬁcations (measured @ Ta= 25°C, full load after warm up unless otherwise stated)

RBB10-2.0-EVM-1

Pin Name Description

1,2 Vin Positive Input Voltage (observe correct polarity!)

3 NC Not connected

4,5 GND Negative Input Voltage (Common GND )

Pin Name Description

1 ON Connect to Vin

2 EN Enable Pin (leae open if not used)

3 OFF Connected to GND

Pin Name Description

1,2 Vout Positive Output Voltage

3 SENSE Output Voltage Sense Pin (leave open if not used)

4,5 GND Negative Output Voltage (Common GND )

Pin Name Description

1 PG Not used

2 SEQ Not used

3 MODE Regulation mode (leave open if not used)

4 VSEL Not used

Connector Description

Con1

Con3

Con2

Con4

Component Placement

CON1

IC1

CON2

CON4

CON3

C8 L4

VOUT

SEQ

RECOM 12.2x12.2mm Evaluation Board

version 03

VSEL

OFFON

SENSE

GND

VIN

MODE

GND

www.recom-power.com REV.: 1/2019 P-4

Evaluation Module

Speciﬁcations (measured @ Ta= 25°C, full load after warm up unless otherwise stated)

RBB10-2.0-EVM-1

1206

L5 0805

1206

1 2

0603

1 2

0603

CON1-B

CON1-D

CON3-C

CON4-C

vsel

0E0

0603

100mW

L2 0805

CON2-D

TRIM

GND2

GND

GND3

OUT

SENSE

MODE

IC1-A

IC1-M

CON4-A

sense

CON2-C

L1 0603

vin

L3 1206

L4 0603

vout

L6 1206

CON4-D

1206

1 2

R6 0603

1206

1 2

0603

1206

CON1-E

1 2

0603

CON2-E

CON4-B

1210

CON2-B

1206

1 2

0603

CON3-B

CON1-A

0603

CON3-A

CON2-A

OUT

VSEL

GND

SEQ

SENSE

MODE

Schematic

Description

IC1 is the RBB10-2.0 power module.

C1,C2,L1,L2,L3,L7,C5,C6 give the possibility to try different input EMC ﬁlters. The populated ﬁlter is designed to meet EN55032 class B has

C1, L7 and C6 ﬁtted.

C7,C8,L4,L5,L6,L8,C3,C4 give the possibility to try different output EMC ﬁlters. The populated ﬁlter is designed to meet EN55032 class B has

L8 and C3 ﬁtted.

R1 and R2 give the possibility to preset the Enable pin in other conﬁgurations.

These resistors are not populated. The default for IC1 is always on.

If R2 is ﬁtted, then the enable is normally on, pull down to ground to turn off. If R1 is ﬁtted, the enable is normally off, pull up to Vin to turn on.

Refer to the datasheet of IC1 for more information.

C9 is not populated on this board.

R3 is a populated 0Ωresistor for output voltage sensing directly at the module output. If the output sense input is required at the point of load,

unsolder R3 and connect the Sense pin to the load.

R4 gives the possibility to compensate the output voltage for any voltage drop through the EMC ﬁlter by unsoldering R3 and soldering it at the

position of R4.

R7 and R8 are not populated on this Board.

R5 and R6 give the possibility to trim the output voltage between 1.0V and 5.5V (see calculations and trim table below). Fit only R5 or R6.

www.recom-power.com REV.: 1/2019 P-5

Evaluation Module

Speciﬁcations (measured @ Ta= 25°C, full load after warm up unless otherwise stated)

RBB10-2.0-EVM-1

OUTPUT VOLTAGE TRIMMING

The RBB10-2.0 series offers the feature of trimming the output voltage over a range between 1.0V and 5.5V by using external trim resistors.

The values for trim resistors shown in trim tables below are according to standard E96 values; therefore, the speciﬁed voltage may slightly vary.

Rup

+Vout

Trim

Rdown

GND

Trim

Trim up Trim down

Voutnom R1R2R3Vref

5VDC 629kW1kW788kW0.805

Practical Example RBB10-2.0:

Calculation:

Voutnom = nominal output voltage [VDC]

Voutset = trimmed output voltage [VDC]

Vref = reference voltage [VDC]

Rup = trim up resistor [W]

Rdown = trim down resistor [W]

R1, R2, R3= internal resistors [W]

Rup =629k - 1k =1M26W

5.5 - 5.0

Rup according to E96 ≈1M27WRdown according to E96 ≈ 2M55W

Rdown =(4.0 - 0.805) x 788k = 2M52W

5.0 - 4.0

Rdown =(Voutset - Vref) x R3

Voutnom - Voutset

Rup =R1- R2

Voutset - Vnom

Voutset =5.1 5.2 5.3 5.4 5.5 [VDC]

Rup (E96) ≈6M34 3M16 2M10 1M58 1M27 [W]

RBB10-2.0

Trim up

Trim down

Voutset =4.5 4.0 3.5 3.3 3.0 2.5 2.0 1.8 1.5 1.0 [VDC]

Rdown (E96) ≈5M90 2M55 1M43 1M15 866k 536k 316k 243k 158k 38k3 [W]

DIMENSION AND PHYSICAL CHARACTERISTICS

Parameter Type Value

Dimension (LxWxH) 90.0 x 60.0 x 26.0mm

Weight 23.3g typ.

www.recom-power.com REV.: 1/2019 P-6

Evaluation Module

Speciﬁcations (measured @ Ta= 25°C, full load after warm up unless otherwise stated)

RBB10-2.0-EVM-1

continued on next page

BOM

Comp. Description Manufacturer Part Number Manufacturer Remarks

C1 22µF 10V X7R 1206 CL31B226MPHNNNE Samsung

C2 10µF ±10% 63V X7R MLCC 1210 GRM32ER71J106KA12L Murata not mounted

C3 10µF 35V X7R 1206 GMK316AB7106KL-TR Taiyo Yuden

C4 10µF ±10% 63V X7R MLCC 1210 GRM32ER71J106KA12L Murata not mounted

C5 22µF 10V 1206 CL31B226MPHNNNE Samsung

C6 22µF 10V X7R 1206 CL31B226MPHNNNE Samsung

C7 10µF 35V X7R 1206 GMK316AB7106KL-TR Taiyo Yuden not mounted

C8 10µF 35V X7R 1206 GMK316AB7106KL-TR Taiyo Yuden not mounted

C9 CAP CER 100nF 50V X7R 1206 CL31B104KBCNNNC Samsung not mounted

CON1 RS Pro Header 2.54mm 5 W81105T3825RC RS

CON2 RS Pro Header 2.54mm 5 W81105T3825RC RS

CON3 RS Pro Header 2.54mm 3 W81103T3825RC RS

CON4 RS Pro Header 2.54mm 4 W81104T3825RC RS

L1 FERRITE BEAD 600 OHM 0603 1LN 742792651 Wurth not mounted

L2 FERRITE BEAD 330 OHM 0805 1LN FBMH2012HM331-T Taiyo Yuden not mounted

Layout

Notes:

Note2: Visit www.recom-power.com/eval-ref-boards to download the Gerber ﬁles

Top Layer Layer 2 (GND)

Bottom (GND)

Layer 3 (GND)

www.recom-power.com REV.: 1/2019 P-7

Evaluation Module

Speciﬁcations (measured @ Ta= 25°C, full load after warm up unless otherwise stated)

RBB10-2.0-EVM-1

Comp. Description Manufacturer Part Number Manufacturer Remarks

L3 FERRITE BEAD 300 OHM 1206 1LN 74279215 Würth

L4 FERRITE BEAD 600 OHM 0603 1LN 742792651 Wurth not mounted

L5 FERRITE BEAD 330 OHM 0805 1LN FBMH2012HM331-T Taiyo Yuden not mounted

L6 FERRITE BEAD 300 OHM 1206 1LN 74279215 Würth

L7 FERRITE BEAD 98 OHM 2SMD 1LN 7427932 Würth not mounted

L8 FERRITE BEAD 98 OHM 2SMD 1LN 7427932 Würth not mounted

R1 RES SMD 1M OHM 1% 1/10W 0603 RC0603FR-071ML Yageo not mounted

R2 RES SMD 1M OHM 1% 1/10W 0603 RC0603FR-071ML Yageo not mounted

R3 RES SMD 0.0OHM JUMPER 1/10W 0603 RC0603JR-070RL Yageo

R4 RES SMD 0.0OHM JUMPER 1/10W 0603 RC0603JR-070RL Yageo not mounted

R5 RES SMD 1/10W 0603 not mounted

R6 RES SMD 1/10W 0603 not mounted

R7 RES SMD 0.0OHM JUMPER 1/10W 0603 RC0603JR-070RL Yageo not mounted

R8 RES SMD 0.0OHM JUMPER 1/10W 0603 RC0603JR-070RL Yageo not mounted

SP1-4 PCB Spacer 4mm

IC1 RBB10-2.0 Module RECOM

• RBB10-2.0-EVM-1 Evaluation Module PCB

• Terms and Conditions

Contents

The product information and speciﬁcations may be subject to changes even without prior written notice.The product has been designed for various applications; its suitability lies in the responsibility of each customer. The

products are not authorized for use in safety-critical applications without RECOM’s explicit written consent. A safety-critical application is an application where a failure may reasonably be expected to endanger or cause

loss of life, inﬂict bodily harm or damage property. The applicant shall indemnify and hold harmless RECOM, its afﬁliated companies and its representatives against any damage claims in connection with the unauthorized

use of RECOM products in such safety-critical applications.

PACKAGING INFORMATION

Parameter Type Value

Packaging Dimension (LxWxH) carton 200.0 x 135.0 x 68.0mm

Packaging Quantity 1pcs

Inhaltsverzeichnis

Andere Recom Steuereinheit Handbücher