Recordex StudioJet 50 Bedienungsanleitung
50 or 100 Disc AutoPrinter
QUICKSTART GUIDE
StudioJet AutoPrinter
Manual for Models:
StudioJet 50™
StudioJet 100™
Recordex® StudioJet 50™/StudioJet 100™ AutoPrinter - QuickStart Guide
Page 3
The specific return policy for your printer will depend on the re-
turn policy of the Recordex retailer/dealer where you purchased your autoprinter.
Recordex will not accept any returned printers if the ink car-
tridges have been installed. Once the printer has been opened and ink cartridges have
been installed the user agrees to keep the printer and the 30-day return policy is void. If
there is a manufacturer defect with your printer we will make sure that your printer is
repaired or replaced, at our discretion, during the first 12-months of ownership.
Do not install the ink cartridges unless you plan to keep the printer!
The box and foam used to package your printer
for shipping is specially designed to prevent shipping damage. If your printer requires
service during the warranty period and you don’t have original packaging we will send
you a replacement set but the cost for a replacement set is $45.00. So we recommend
hanging on to the original box & foam.
To save space you can remove the packing tape from the top and bot-
tom of your printer box and fold the box flat. This might free up a little room in your at-
tic!
When calling for service we will need
to know the serial number of your StudioJet Printer, the date of purchase, and the name
of the company that sold you your StudioJet Printer.
Your serial number is located on the outside of your printer
box. You’ll also find the Model number listed on the same label. We recommend writing
the Serial number down in the inside cover of your User’s Manual.
If after reading the user’s manual you’re still having trouble with your
StudioJet Disc AutoPrinter then give us a call or drop us a line. Service Phone: 478-
IMPORTANT! READ FIRST!
Recordex® StudioJet 50™/StudioJet 100™ AutoPrinter - QuickStart Guide
Verify the contents of your package against the image below.
Using a pair of scissors cut the plastic packing strip holding the disc tray in
place.
Remove plastic film from printer chassis. (NOTE: Once plastic film is removed
the printer can not be returned for a refund.)
Save the box and packaging material for return shipment should your printer
require service.
STEP 1: Unbox and Verify Contents
Figure 1.1 Printer Contents
NOTE: StudioJet 50 Depicted. StudioJet 100™
will include a 100 capacity output bin and longer
input spindles.
Page 5
STEP 2: Assemble AutoPrinter
Slide the output bin into the right front
of the printer base.
(see Figure 2.1)
Screw the four input spindles down onto
the top of the loading mechanism.
(see Figure 2.2)
Load blank inkjet printable media into
the input bin on the top of the printer.
(see Figure 2.3)
Figure 2.1 Insert Output Bin
Figure 2.2 Assemble Input Spindles
Figure 2.3 Load Blank Media
Recordex® StudioJet 50™/StudioJet 100™ AutoPrinter - QuickStart Guide
STEP 3: Connect Power to Printer
1. Connect the power cord to the power adapter.
2. Connect the power adapter to the printer.
3. Connect the power cord to the wall outlet.
NOTE: Use only a grounded outlet. It is highly recommended that you pro-
tect your printer from electrical damage by connecting it to a surge protec-
tor or an uninterruptible power supply (UPS).
STEP 4: Install Ink Cartridges
1. Open printer cover and wait for cartridges to stop moving.
2. Remove protective film from cartridge. (see Figure 4.1.)
3. Lift Cartridge cover and insert cartridge into printer. (See Figure 4.1)
NOTE: The cartridges provided with your printer are starter cartridges and
will provide approximately ½ the yield of a standard cartridge. For the low-
est cost per print
Figure 3.1 Connect Power
Figure 4.1 Remove Protective Film & Insert Cartridge
Page 7
STEP 5: Install XP Printer Driver
Insert the StudioJe™t Installation Disc into
your CD/DVD drive. After a few seconds an
installation menu will be displayed. For now
you can ignore the install menu.
Connect the StudioJet™ to your computer
with the supplied USB cable. After a few sec-
onds the computer will report that it has
found new hardware. If this does not happen
check to make sure there is power to the
printer and that the printer is plugged into
your computer. Try reconnecting the USB ca-
ble.
After the computer reports that it has found
new hardware simply follow the Add New
Hardware Wizard to install the printer driver.
Refer to the screen shots to the right as you
proceed through the Add New Hardware wiz-
ard.
Recordex® StudioJet 50™/StudioJet 100™ AutoPrinter - QuickStart Guide
Insert the StudioJet™ Installation Disc into
your CD/DVD drive. After a few seconds an
installation menu will be displayed. For now
you can ignore the install menu.
Connect the StudioJet™ to your computer
with the supplied USB cable. After a few sec-
onds the computer will report that it has
found new hardware. If this does not happen
check to make sure there is power to the
printer and that the printer is plugged into
your computer. Try reconnecting the Power
and USB cables.
After the computer reports that it has found
new hardware simply follow the Add New
Hardware Wizard to install the printer driver.
Refer to the screen shots to the left as you
proceed through the Add New Hardware wiz-
ard.
STEP 5b: Install Vista Printer Driver
Page 9
STEP 6: Install QuickTime 7.0
In order to use the included Discus LE 4 disc
label editor software you need to install Quick-
Time 7.0 or later on your computer.
To install QuickTime click on the install button
on the Install Menu and follow the installation
prompts. (see figure 6.1)
NOTE: If the install menu is not showing on
your screen make sure the install/setup disc
is in your CD/DVD drive. If the menu does not
appear after 20-30 seconds then try running
it manually by:
• Click Start
• Click Run
• Type E:\Setup.exe (where E is the drive
letter for you CD/DVD drive) and press
Enter.
• The Install Menu will appear.
STEP 7: Install Discus LE 4
To install the bundled version of Discus Label
Editor simply click on the Install button on the
Installation menu. (see figure 7.1)
Follow the on-screen prompts to complete the
installation.
Figure 6.1 Install QuickTime
Figure 7.1 Install Discus LE 4
Recordex® StudioJet 50™/StudioJet 100™ AutoPrinter - QuickStart Guide
STEP 8: Using Discus For the First Time
The first time you use Discus you will need to unlock the software by entering
the software serial number/registration key. This number can be found on
the front of your installation disc. If you can’t find your install disc check your
DVD/CD drive since you likely just finished installing Discus!
The software is quite easy to use and after a few minutes of experimenting
you’ll be creating incredible labels. We recommend reading through the Dis-
cus User Manual (available on the help menu when using Discus) to familiar-
ize yourself with the application. Note: the manual includes how to create
jewel case inserts. This function is not available with the version of Discus
bundled with your printer, however, the layout methods are the same for la-
bels and inserts so it is still worth reading!
• Try using your own pictures. You’ll be amazed at the photo-quality printing
you can achieve with your StudioJet™ Disc AutoPrinter.
• Experiment with Discus. You’ll learn the fastest if you just sit down and
play with the software.
• Be sure to select the type of media that you are using on the Print tab (I.e.
Hub-Printable, or Standard).
•If your StudioJet™ isn’t set as your default printer, you’ll need to
remember to select it as your printer when you print from Discus,
otherwise you’re disc print job will be sent to one of the other printers
installed on your computer.
Phone: 415-669-7010 (10am to 7pm PST)
Fax: 415-669-7009
Email: [email protected]
Web: http://www.magicmouse.com/h_support.html
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
