Redline Communications RDL-3100-RMA Bedienungsanleitung

RDL-3100

RDL-3100 Family

Broadband Wireless Systems

RDL-3100-RMA

Radio Modules

Product Manual

1Product Overview...................................................................6

2Conditions of Use...................................................................7

3Module Installation and Service ............................................8

4Final Product Requirements................................................11

5Regulatory Notices...............................................................22

RDL-3100 RMA MODULE PRODUCT MANUAL

Redline Communications Inc. This document may not in whole or in part be copied,

reproduced, or reduced to any medium without prior consent in writing from Redline

Communications Incorporated.

Contact Information

Contact Information:

Redline Communications Inc.

302 Town Centre Blvd.

Markham, ON

Canada L3R 0E8

Web site: http://www.rdlcom.com

Email:

Inquiries: [email protected]

Support: support@rdlcom.com

Training: training@rdlcom.com

Document Control:

70-00184-05-00-RDL-3100-RMA_Module_Product_Manual-20170215a.doc

Disclaimer

The statements, configurations, technical data, and recommendations in this document

are believed to be accurate and reliable, but are presented without express or implied

warranty. Additionally, Redline makes no representations or warranties, either expressed

or implied, regarding the contents of this product. Redline Communications shall not be

liable for any misuse regarding this product. The information in this document is subject

to change without notice. No part of this document shall be deemed to be part of any

warranty or contract unless specifically referenced to be part of such warranty or

contract within this document.

RDL-3100 RMA MODULE PRODUCT MANUAL

TABLE OF CONTENTS

1Product Overview...................................................................6

2Conditions of Use...................................................................7

2.1 General Conditions............................................................................................7

2.2 Country of Use...................................................................................................7

2.3 Product Labeling................................................................................................8

2.3.1 Module Label ....................................................................................................8

2.3.2 External Label...................................................................................................8

3Module Installation and Service ............................................8

3.1 Installation into a Final Product........................................................................8

3.2 Module Servicing...............................................................................................9

3.3 Professional Installation..................................................................................10

3.4 Safety Precautions...........................................................................................10

3.5 Radio Frequency Safety..................................................................................10

4Final Product Requirements................................................11

4.1 Frequency Bands.............................................................................................11

4.1.1 Antenna Use and Transmit Power...................................................................11

4.1.2 Certified Antennas ..........................................................................................11

4.1.3 Power & EIRP (MIMO Operation)....................................................................12

4.9 GHz: FCC 47 CFR Part 90 Subpart Y and RSS-III...................................12

5.2 GHz: FCC 47 CFR Part 15 Subpart E, §15.407.......................................13

5.8 GHz: FCC Part 15 Subpart Е and RSS-247 Issue 1 ................................14

5Regulatory Notices...............................................................22

5.1.1 FCC Notices ...................................................................................................22

5.1.2 ISED Notices...................................................................................................23

RDL-3100 RMA MODULE PRODUCT MANUAL

LIST OF TABLES

Table 1: Approved Antennas.........................................................................................11

Table 2: FCC 4.9 GHz: output power: 10 MHz channel, 10 dBi and 24 dBi antennas....12

Table 3: FCC 4.9 GHz: output power: 10 MHz channel, 32 dBi antenna........................12

Table 4: FCC 4.9 GHz: output power: 20 MHz channel, 10 dBi and 24 dBi antennas....12

Table 5: FCC 4.9 GHz: output power: 20 MHz channel, 32 dBi antenna........................12

Table 6: FCC 5.2 GHz: output power: 10 MHz channel, PMP 10 dBi antenna...............13

Table 7: FCC 5.2 GHz: output power: 10 MHz channel, PMP 24 dBi antenna...............13

Table 8: FCC 5.2 GHz: output power: 10 MHz channel, PMP 32 dBi antenna...............13

Table 9: FCC 5.2 GHz: output power: 20 MHz channel, PMP 10 dBi antenna...............13

Table 10: FCC 5.2 GHz: output power: 20 MHz channel, PMP 24 dBi antenna.............13

Table 11: FCC 5.2 GHz: output power: 20 MHz channel, PMP 32 dBi antenna.............14

Table 12: FCC 5.2 GHz: output power: 40 MHz channel, PMP 10 dBi antenna.............14

Table 13: FCC 5.2 GHz: output power: 40 MHz channel, PMP 24 dBi antenna.............14

Table 14: FCC 5.2 GHz: output power: 40 MHz channel, PMP 32 dBi antenna.............14

Table 15: FCC 5.8 GHz: output power: 10 MHz channel, PMP 10 dBi antenna.............14

Table 16: FCC 5.8 GHz: output power: 10 MHz channel, PMP 24 dBi antenna.............15

Table 17: FCC 5.8 GHz: output power: 10 MHz channel, PMP 32 dBi antenna.............15

Table 18: FCC 5.8 GHz: output power: 20 MHz channel, PMP 10 dBi antenna.............15

Table 19: FCC 5.8 GHz: output power: 20 MHz channel, PMP 24 dBi antenna.............15

Table 20: FCC 5.8 GHz: output power: 20 MHz channel, PMP 32 dBi antenna.............15

Table 21: FCC 5.8 GHz: output power: 40 MHz channel, PMP 10 dBi antenna.............16

Table 22: FCC 5.8 GHz: output power: 40 MHz channel, PMP 24 dBi antenna.............16

Table 23: FCC 5.8 GHz: output power: 40 MHz channel, PMP 32 dBi antenna.............16

Table 24: ISED 5.8 GHz: output power: 10 MHz channel, PMP 10 dBi antenna............16

Table 25: ISED 5.8 GHz: output power: 10 MHz channel, PMP 24 dBi antenna............16

Table 26: ISED 5.8 GHz: output power: 10 MHz channel, PMP 32 dBi antenna............17

Table 27: ISED 5.8 GHz: output power: 20 MHz channel, PMP 10 dBi antenna............17

Table 28: ISED 5.8 GHz: output power: 20 MHz channel, PMP 24 dBi antenna............17

Table 29: ISED 5.8 GHz: output power: 20 MHz channel, PMP 32 dBi antenna............17

Table 30: ISED 5.8 GHz: output power: 40 MHz channel, PMP 10 dBi antenna............17

Table 31: ISED 5.8 GHz: output power: 40 MHz channel, PMP 24 dBi antenna............18

Table 32: ISED 5.8 GHz: output power: 40 MHz channel, PMP 32 dBi antenna............18

Table 33: FCC 5.8 GHz: output power: 10 MHz channel, PTP 10 dBi & 24 dBi antenna18

Table 34: FCC 5.8 GHz: output power: 10 MHz channel, PTP 32 dBi antenna..............18

Table 35: FCC 5.8 GHz: output power: 20 MHz channel, PTP 10 dBi & 24 dBi antenna18

Table 36: FCC 5.8 GHz: output power: 20 MHz channel, PTP 32 dBi antenna..............19

Table 37: FCC 5.8 GHz: output power: 40 MHz channel, PTP 10 dBi & 24 dBi antenna19

Table 38: FCC 5.8 GHz: output power: 40 MHz channel, PTP 32 dBi antenna..............19

Table 39: ISED 5.8 GHz: output power: 10 MHz channel, PTP 10 dBi antenna.............19

Table 40: ISED 5.8 GHz: output power: 10 MHz channel, PTP 24 dBi antenna.............19

Table 41: ISED 5.8 GHz: output power: 10 MHz channel, PTP 32 dBi antenna.............20

Table 42: ISED 5.8 GHz: output power: 20 MHz channel, PTP 10 dBi antenna.............20

Table 43: ISED 5.8 GHz: output power: 20 MHz channel, PTP 24 dBi antenna.............20

Table 44: ISED 5.8 GHz: output power: 20 MHz channel, PTP 32 dBi antenna.............20

Table 45: ISED 5.8 GHz: output power: 40 MHz channel, PTP 10 dBi antenna.............20

Table 46: ISED 5.8 GHz: output power: 40 MHz channel, PTP 24 dBi antenna.............21

RDL-3100 RMA MODULE PRODUCT MANUAL

Table 47: ISED 5.8 GHz: output power: 40 MHz channel, PTP 32 dBi antenna.............21

Table 48: FCC: RDL-3100-RMA Recommended Safe Distances ..................................22

Table 49: ISED: RDL-3100-RMA Recommended Safe Distances .................................23

Table 50: ISED: RDL-3100-RMA distances de sécurité recommandées........................24

RDL-3100 RMA MODULE PRODUCT MANUAL

1 Product Overview

The RDL-3100-RMA radio module is comprised of a proprietary Media Access Control

(MAC) protocol engine and Time Division Duplexing (TDD)/ Orthogonal Frequency

Division Duplexing (OFDM) digital radio.

The module is not designed for stand-alone operation. The module is sold as one

component of a packaged system which includes a suitable housing for the module

connectors for required external components including a power supply and antenna

system. This is afterwards referred to as the 'final product'. The final product may be

designed and manufactured by Redline or a licensed third party.

Frequency settings within the specified frequency ranges are software keyed to be

compliant with specific regulatory agency requirements in the region of deployment.

USA & Canada: 4900 to 5975 MHz

Important: Read this entire document prior to installing or operating these modules.

RDL-3100 RMA MODULE PRODUCT MANUAL

2 Conditions of Use

2.1 General Conditions

The RDL-3100-RMA module is not provided for sale to the general public. The module

contains a proprietary radio interface and can not be directly connected to any standard

telecommunications or computer devices. This manual is provided as supplement to

technical and operational documentation and training provided by Redline and its

agents.

Any operation or use of this module in any manner not expressly specified within this

manual or approved in writing by Redline (or its agents) is expressly forbidden and voids

the users right to operate the module. This includes, but is not limited to, any

modification of the module hardware or software, installation of the module in a non

approved enclosure, and use with non approved antennas.

2.2 Country of Use

Refer to the regulatory notices in this document before installing or operating the

module.

Operation of the final product requires a software 'key' that is available exclusively from

Redline or its authorized agents. The software key is unique to each module and must

be installed and activated before the radio will operate. The key contains sufficient

security features that the professional installer and operator can not decode, modify,

substitute, or otherwise circumvent the operational restrictions imposed by the 'key'.

The software 'key' limits the transmit power, operating frequency range, and channel

bandwidth per the regulator domain governing the location where the radio will be

deployed. The operator does not have the option to select the country or regulatory

region of operation.

The software 'key' limits the mode of operation as a master or client. The client mode is

'passive listener' and while in this mode the module can not initiate any transmission

without first receiving and decoding a valid authorization message from the master. A

module with a key for client operation can not be changed by the installer to enable

master mode operation. A module with a key for master operation can operate in master

or client (passive) mode.

Operation in the United States

The RDL-3100-RMA module is certified with limited modular approval for use as an

'intentional radiator' in the United States as device FCC ID: QC8-RDL3100RMA.

Operation in Canada

The RDL-3100-RMA module is certified with limited modular approval for use as an

'intentional radiator' in the Canada as IC: 4310A-RDL3100RMA.

RDL-3100 RMA MODULE PRODUCT MANUAL

2.3 Product Labeling

2.3.1 Module Label

The modular transmitter will display a label referring to the FCC ID registration number

and the IC registration number. An information label is applied directly to the modular

transmitter (example shown below).

Do not to remove any labels from the module.

2.3.2 External Label

Information labels are applied to the final product. The final product features a label on

the outside surface listing the registration number for the enclosed module. Do not to

remove any labels from the module or the final product.

3 Module Installation and Service

3.1 Installation into a Final Product

The module must be installed only by trained professional technicians authorized by

Redline or its agents. The module must be installed only into an approved enclosure

(see Conditions of Use) and only at an approved manufacturing facility or service depot.

Redline shall retain complete control over the final installation of the module and will

ensure compliance of the end product to all applicable FCC/ISED regulations. The

module must be installed only into an approved enclosure (see Conditions of Use) and

only at an approved manufacturing facility or service depot.

Redline licensing of the modular transmitter includes monitoring to ensure compliance in

the operation and use of the module as expressly specified within this manual. This

includes restrictions against modification of the module hardware, approval of the final

RDL-3100 RMA MODULE PRODUCT MANUAL

enclosure, operational restrictions for installers and end-users, and approval of antennas

provided for use with the product.

Operation of the final product requires the 'key' be controlled exclusively by the

manufacturer. The 'key' must be unique to each module and must be installed and

activated before the radio will operate. The key must contain sufficient security features

to the professional installer and operator can not decode, modify, substitute, or

otherwise circumvent the operational restrictions imposed by the 'key'.

The software 'key' must limit the transmit power, operating frequency range, and channel

bandwidth per the regulator domain governing the location where the radio will be

deployed. The operator does not have the option to select the country or regulatory

region of operation.

The software 'key' must limit the mode of operation as a master or client. The client

mode is 'passive listener' and while in this mode the module can not initiate any

transmission without first receiving and decoding a valid authorization message from the

master. A module with a key for client operation can not be changed by the installer to

enable master mode operation.

Redline will review all final products for compliance to regulatory restrictions.

The manufacturer must meet all labeling described in section 2.3.

3.2 Module Servicing

The module is not intended to be field serviceable, and contains no field serviceable or

field replaceable parts. The module must be serviced only at an approved manufacturing

facility or service depot.

Warning: The module is susceptible to damage from electrostatic charge.

Electrostatic Discharge (ESD) must be avoided to prevent damaging or destroying the

module. The module must always be store in an anti-static container/bag prior to

installation and following removal from the product for servicing. Observe ESD

precautions when handling the module.

RDL-3100 RMA MODULE PRODUCT MANUAL

3.3 Professional Installation

Devices containing the module require professional installation. It is the responsibility

of the installer to understand the product operation by attending training as required,

reading and understanding the product documentation, and ensuring that all building,

safety and regulatory codes are met and the installation is complete and secure.

3.4 Safety Precautions

Installation and service of the module must be performed by personnel having technical

training and experience necessary to be aware of hazards during installation and/or

service of RF equipment. The installation and/or service must be done using procedures

designed to minimize any danger to technical personnel or any other person.

3.5 Radio Frequency Safety

The installer of this radio equipment must ensure the antenna is located or pointed such

that it does not emit RF fields in excess of the general population limits as defined by:

FCC CFR 47, Part 2.1091

http://www.gpo.gov/fdsys/pkg/CFR-2009-title47-vol1/pdf/CFR-2009-title47-vol1-sec2-

1091.pdf

FCC OET Bulletin 65, Radio frequency radiation exposure evaluation for fixed

devices

http://transition.fcc.gov/Bureaus/Engineering_Technology/Documents/bulletins/oet65

/oet65c.pdf

Health Canada limits for the general population; consult Safety Code 6, obtainable

from Health Canada’s website:

http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-eng.php

Refer to the regulatory statements included in this document.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Redline Communications Steuereinheit Handbücher

Redline Communications

Redline Communications RDL-3000 Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung