Redline RL-101 Bedienungsanleitung

10350 STATE HWY 30 College Station, TX 77845

(979) 776-7200

RL-101 Installation and Operation Manual

SAFETY MESSAGE

•It is important to follow all instructions in this manual.

•This device is to be installed by a trained professional

who is familiar with Redline Safety products.

•Read and understand all instructions before installation

or use of this equipment.

•Keep cover tight when circuits are alive.

•Test Instrument regularly to ensure it is operating

properly.

IMPORTANT SAFETY WARNING

Failure to follow all safety and operational instructions

may result in instrument damage, serious injury or

death.

Power Consumption and Voltage rating

RL101 instrument is powered by 6 AA batteries

(9VDC) internally.

360uA continuous consumption when the device is

operational.

INSTRUMENT HOUSING

This product is housed in a Limatherm Instrument Housing

Type XD-Iwin

CL. I. GR. A,B,C,D; CL.II. GR. E,F,G CL.III; TYPE 4X

CL. ZONE 1 Ambient TEMP -40C to 85C

After installation provide a copy of manual to authorized personnel

OPERATIONS OVERVIEW

Modes

1. Normal Operation

2. NULL

3. Calibrate

4. Assign Head Address

5. Set Background Gas Level

6. Check Battery Voltage

7. Select Redline or WF784 Radio Message

8. Revision

9. Relay Test

10. Radio Signal Strength Input

11. Select Redline or WF784 Radio Message (same as step 7)

12. OFF

13. Startup

Basic Operation

There are three main modes for the RL101 Head Unit. In addition, there is an OFF

mode and a Startup mode. When the unit is powered, there is a 30 second

(Startup) countdown during which some system values are displayed before going into the

Normal Operating mode.

To get to the second mode this is addressing. Press TEST to get to the third Mode, press TEST again

while in the 2nd Mode. Pressing TEST while in the 3rd Mode will get back into the 2nd mode or

addressing. Pressing MENU multiple times will get back to Normal Operating mode.

If left in any mode (except OFF), the unit will return to Normal Mode after three minutes.

When the Head unit changes modes, it will send a message to the Monitor.

Menu Reed

Test Reed

Up Reed

Down Reed

Buttons for changing

modes

Radio antenna

XBee Pro 2.4G Radio

Connector for RL-SSH

H2S Sensor Housing

9VDC in

1. Normal Operation

The RL101 Head unit monitors the gas level. If the gas level is greater than or equal to the background

setting, the unit will send a message every 5 seconds; if less than the background setting, the unit will

send a message every 5 minutes. When the Rl101CB is in normal mode it will display a zero.

2. NULL

To place the Rl101 into NULL Mode press MENU button our use the magnet with the reed switch once

"NUL" will flash on the display. The RL101 Head unit monitors the gas level but does not send messages

when in NULL Mode. NULL Mode is used removing any errors in the amplifiers that may cause a gas

reading when there is no gas. Use the Up or Down buttons to adjust the readings to zero.

Press menu button or use the reed

once to enter “nul” mode

3. Calibration

To place the Rl101 into CAL Mode press the MENU button twice "CAL" will flash on the display.

The RL101 Head unit monitors the gas level but does not send messages to the monitor when in

CALIBRATION mode.When calibration gas is applied, the unit will display the reading. Use the Up and

Down buttons to adjust the reading to match the value of the calibration gas. Pressing MENU will place

the unit in Normal Operation and will begin sending messages to the monitor.

4. Assign Radio (Head) to Channel

To access to this feature press TEST once, "Adr" will flash on the display when in that mode.

Use the UP and Down buttons to adjust the Address of the Head unit. There must be a corresponding

address set in the Monitor.

Press Menu button or

use reed switch twice to

enter “CAL” mode

Use the Up and Down buttons to

adjust the reading to match the value

of the calibration gas

Use the UP and Down buttons or reed

switch to adjust the Address of the

Head unit.

To access to this feature

press TEST button or use

reed switch once

5. Set Background Gas Level

To access to this feature press TEST once then MENU once "brd" will flash on the display when in that

mode. (Default setting is 7) Use the Up and Down buttons to adjust the Background level.

When the gas level is equal to or greater than this number, the unit will transmit a message every 5

seconds; if less

than this setting, the unit transmit every 5 minutes..

6. Check Battery Voltage

This mode displays the condition of the batteries. To access to this feature press TEST once then MENU

twice "bat" will flash on the display when in this mode.

7. Select Redline message or 784 message

(This mode is new to revisions 2.0 or greater). If the RL101 sensor head is in the wrong setting of 784,

use the up or down buttons to change back to “Red”.

** if the RL101 sensor head is in 784 it will not communicate to the Redline Monitor**

8. Revision

This mode shows the revision of the software that is being used in the RL101 Head unit. To access press

TEST Twice.

9. Relay Test

To place the RL101 sensor Head in relay test mode press the TEST button twice and the MENU button

once “REL” will show on the display. Use the Up and Down buttons to adjust the PPM value to send in a

message to the Monitor.

The Monitor treats this PPM value in the same way it would treat an actual gas reading.

This will allow for the relays in the Monitor to be activated and shows that the Head unit

is communicating with the Monitor.

10. Radio Signal Strength Input

To get to this mode press the TEST button twice and the MENU button twice "rIn" will then flash

in the display. This mode allows the Head unit and Monitor to exchange messages (this mode is disabled

when in the 784 mode since the 784 does not resend any messages). When the Head unit sends a

message, the Monitor knows that the Head unit is in this mode and resends the message. The

Head unit stays awake in order to receive this resent message. The Head unit measures the

strength of the signal and displays it (the maximum Value is 255); the units should work

properly until the signal level drops to about 50.

( Caution: since the radio stays awake for this test, the battery is being discharged much faster in this

mode, so try to spend as little time in this test as possible.)

The Head unit transmits a message once per second and the Monitor responds immediately, so

the test must be performed for at least one

second. The Head unit can be moved away from obstructions, up or down or pointed to get

the best reading. When the MENU button is pressed to leave this mode, the last reading

taken will be stored in memory; the stored reading will be included in the messages to the

Monitor, so this reading can be examined at the Monitor. If no Monitor is in range, the

readings will be very low or zero.

11. OFF

To put the Head unit in the OFF mode, press the TEST button for about 4 seconds. The

display will show "OFF".

This mode disables all transmissions by the Head unit. The unit will transmit a message every 5

minutes with no gas present or every 5 seconds when the gas level is equal to or greater

than the background setting. To reduce the battery discharge, the unit can be set in OFF

mode, where it will never transmit. To wake the Head unit, press MENU, Up or TEST, and the unit will

begin the start up sequence.

12. Startup

When the RL101 is powered or awakened, it will display several values, like gas type,

address and battery voltage, then the unit will count up to 30 seconds and go into normal operation.

INSTALLATION

Important- before you install the Rl101 h2s head make sure you have read the basic operations

to ensure proper understanding of the product. Also check battery voltage to ensure Rl101 will function

properly.

When installing the Rl101 h2s Head make sure to calibrate the sensor head. Put the Head into “cal”

mode. When calibration gas is applied, the unit will display the reading. Use the Up and Down buttons

to adjust the reading to match the value of the calibration gas. ( # 3 in basic operations)

The Rl101 Head may be mounted 18 to 24 inches above the ground with the sensor housing pointed

down towards the ground. For best signal strength position the glass window in line of sight of the

Redline Monitor, also make sure there are no metal/nonmetal obstructions so signal will not be blocked.

MAINTENANCE

Redline Instruments recommends you check battery voltage every 90 days and Calibration of the head

every 30 days. Recommended battery replacement at 7.5VDC or lower, if battery is at 5.3VDC there will

not be sufficient power to transmit a signal. If your instrument is in need of repair you may send your

instrument to any of the redline location for repair. See website for location addresses. For

Troubleshooting assistance call the Redline office at (979)776-7200.

Inhaltsverzeichnis

Andere Redline Gaswarngerät Handbücher

Redline

Redline RL-101U Bedienungsanleitung

Beliebte Gaswarngerät Handbücher anderer Marken

Macurco

Macurco GD-6 Bedienungsanleitung

Evikon

Evikon E2632 Bedienungsanleitung

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Bedienungsanleitung

MSA

MSA altair 5 Bedienungsanleitung

DOD Technologies

DOD Technologies ChemLogic CL96 Bedienungsanleitung

DEGA

DEGA NS III LCD Series Bedienungsanleitung

RKI Instruments

RKI Instruments 35-3001A-08-01 Bedienungsanleitung

PEMTECH

PEMTECH PT2008 Series Bedienungsanleitung

Coster

Coster RGS 328 Bedienungsanleitung

Sygonix

Sygonix 2483186 Bedienungsanleitung

Perry

Perry 1GA 50917MET/P Bedienungsanleitung

isweek

isweek AS8900 Bedienungsanleitung

Oldham

Oldham OLC 10 Bedienungsanleitung

Wizmart

Wizmart NB983 Bedienungsanleitung

Beacon

Beacon MEGA Handbuch

RKI

RKI GX-6000 Bedienungsanleitung

Dräger

Dräger PIR 7000 Bedienungsanleitung

GDS

GDS GASMAX EC Bedienungsanleitung