Regency CB40EPV Series Bedienungsanleitung

City Series Power Vent

City Series CB40EPV Gas Fireplace

Model CB40EPV-NG CB40EPV-LP

Fuel Type Natural Gas Propane

Minimum Supply Pressure 5” W.C. (1.25 kPa) 11” W.C. (2.73 kPa)

Manifold Pressure - High 3.8” W.C. (0.94 kPa) 10.5” W.C. (2.62 kPa)

Manifold Pressure - Low 1.1” W.C. (0.27 kPa) 2.9” W.C. (0.72 kPa)

Oriﬁce Size -Altitude 0-4500 ft. #42 DMS #53 DMS

Minimum Input

Altitude 0-4500 ft. (0-1372m)

15,500 BTU/h

(4.54 kW)

15,500 BTU/h

(4.54 kW)

Maximum Input

Altitude 0-4500 ft. (0-1372m)

28,500 BTU/h

(8.33 kW)

28,500 BTU/h

(8.33 kW)

Vent Sizing 4” Inner / 6-5/8” Outer 4” Inner / 6-5/8” Outer

CSA P.4.1 60.02% 60.85%

Caution Requirements

The top, back and sides of the ﬁreplace are deﬁned by

standoffs. The metal ends of the standoff may NOT be

recessed into combustible construction.

WARNING

Fire hazard is an extreme risk

if these clearances (air space) to combustible materials are not

adhered to. It is of greatest importance that this replace and vent

system be installed only in accordance with these instructions.

CLEARANCES CB40EPV

Flue Clearances to

Combustibles

Horizontal - Top 3"

Horizontal - Side 2"

Horizontal - Bottom 2"

Vertical 2"

Passing through wall/ﬂoor/

ceiling - when firestop is

used.

1-1/2"

* A minimum of 120 square inches of open area, not lower than 3" from top of enclosure, required for all

installations — this can be achieved by having an open area in front, each side, and/or above as shown

in the four diagrams on the next page.

The HeatWave Duct Kit has

different clearance and framing

requirements, check the HeatWave

manual for details.

Alcove

Clearance: 3 sided Dimension Measured From:

A: From Floor Min. 0" Bottom of Fireplace Opening

A1 : Mantel Height (min.) ** Top of Fireplace Opening

B: Sidewall (on one side) 8-1/2" (216mm) Side of Fireplace Opening

C: Enclosure Width (min.) 48-7/16" (1230mm) Minimum inside dimensions

D: Mantel Depth (max.) **

E: Alcove Width 84" (2134mm) Side wall to side wall (min.)

F: Alcove Depth 36" (914mm) Front of Unit

G: To Enclosure Ceiling (min/max) 0-3" (76mm) From top of enclosure

H: Convection Air outlet 120 sq. inches (min) * Top/front or side of enclosure

I: Enclosure Depth (min.) 19" (483mm) Minimum inside dimensions

J: Opening Height 15-1/16" (383mm) Bottom/Top of Fireplace Opening

K: To Ceiling (min) All 3 sides 1-1/2" To Top of Ceiling

L: Chase Enclosure (min.) 63" (1600mm) From base of unit/ﬂoor

M: Clearance to Sprinkler Head (Min.) 36" (914mm) Perpendicular from chase grill

Hearth 0" No hearth required

** See mantel clearances chart in this section

Chase grill

Sprinkler

Side view

City Series Power Vent

CB40EPV Gas Fireplace

CLEARANCES CB40EPV

Floor to ceiling with top opening Low framing with vents in front/sides or top

Full framing with low vents in front or sides Full framing with vents in front or sides

City Series Power Vent

CB40EPV Gas Fireplace

City Series Power Vent

CB40EPV Gas Fireplace

FRAMING DIMENSIONS CB40EPV

NOTE: Framing may be constructed of combustible material (ie. 2x4) and does not require steel studs. Two (2) optional steel stud kits may also

be purchased. These kits may be used in place of the conventional wood framing as shown below. It comes as a compact kit (ﬂush to the

appliance on all sides)or an extended kit. The extended kit protrudes beyond each side of the appliance as shown on the front cover of

this manual. There is also an optional hearth kit which may be purchased as shown on the front cover of this manual. These kits are highly

recommended as it was designed speciﬁcally for the product to facilitate ease of installation. See instructions in this manual for details.

Framing

Dimensions Description CB40EPV

A Framing Height 37-3/8” (949mm)

B Framing Width 48-1/2" (1232mm)

C Framing Depth 19" (483mm)

D Minimum Height to Combustibles 63"(1600mm)

G Vent Centerline Height 56-1/4" (1429mm)

I Gas Connection Opening Height 2" (51mm)

J Gas Connection Height 4 " (106mm)

K Gas Connection Inset 13" (330mm)

L Gas Connection Opening Width 3-1/2" (89mm)

Note: A combined minimum of 120 square inches of open area is required for the convection air outlet to cool the enclosure. Ensure clearances

for Convection Air Outlets are met. See clearances CB40E in the unit manual as there are different methods as to how this can be achieved.

Note: Only basic framing dimensions are shown. The framing may also extend beyond the appliance on either side and also extend out front if a

hearth is desired. See clearance/ﬁnishing requirements for details.

Note: Unit is not load bearing. All ﬁnished materials must be supported by framing.

Note: This appliance must be installed on

a solid surface such as a plywood ﬂoor

which must be the full width and depth of

the appliance.

Maximum material

dimensions 2" x 4" for

Header studs (installed

on edge and ﬂat)

City Series Power Vent

CB40EPV Gas Fireplace

MANTEL CLEARANCES CB40EPV

Due to the extreme heat this ﬁreplace emits, the

mantel clearances are critical.

Combustible mantel clearances from top of front facing

are shown in the diagram on the right.

Note: Ensure the paint that is used on the mantel

and the facing is "high quality" or the paint

may discolour.

MANTEL LEG CLEARANCES

Combustible mantel leg clearances as per diagram:

12"

MANTEL LEG

8-1/2"

CB40E

212 6 4810

15-1/16”

Top of

Fireplace

Opening

12" (305mm)

1/2" Drywall, wood, wood panel, etc.

5-1/8"

Bottomof

Fireplace

Opening

City Series Power Vent

The gas power vent system is designed to allow the installation of a gas appliance when typical vent conﬁgurations (shown in this manual) are

not possible.

Important: Minimum overall vent run must be 4 feet.

Maximum total vent length = 72' maximum of six - 90° elbows permitted.

One 90° elbow = two 45° elbows.

Maximum total negative vent length = 7'.

Note: Maximum length of 72 feet is based on overall length of combined

chimney components.

VENTING ARRANGEMENTS FOR HORIZONTAL TERMINATIONS

RIGID PIPE: MUST USE RIGID PIPE ADAPTOR 770-994 AND 946-606 PIPE REDUCER TO 4" X 6 5/8"

Note: Rigid pipe is approved for up to 72 feet.

Note: Flex pipe is approved for up to 40 feet using 2 X 946-756-- 20 foot ﬂex kits.

Horizontal (Feet)

6 10 12 16 18

14 20 22 24

-3 Ft. max.

32 342826 30 36 38 42 44

40 46 48 50 54 5652 58 60

Vertical (Feet)

62 64 66 68 70 72

-2

-4

-6

-8

Restrictor – Factory Set @ 1"

72' overall length Max.

(shown with 5 - 90º elbows)

72' run (no rise)

Shown with 2 elbows (negative run 72')

72' overall length Max.

(shown with 5 - 90º elbows)

Horizontal (Feet)

6 10 12 16 18

14 20 22 24

-3 Ft. max.

32 342826 30 36 38 42 44

40 46 48 50 54 5652 58 60

Vertical (Feet)

62 64 66 68 70 72

-2

-4

-6

-8

Restrictor – Fully Open

72' overall length Max.

(shown with 5 - 90º elbows)

72' run (no rise)

Shown with 2 elbows (negative run 72')

72' overall length Max.

(shown with 5 - 90º elbows)

CB40EPV Gas Fireplace

City Series Power Vent

HORIZONTAL TERMINATIONS

Rigid Pipe 4" x 6-5/8"

The minimum components required for a basic horizontal termination

are:

1 Power Vent Kit

1 Rigid Pipe Adaptor

1 Length of pipe to suit wall thickness and total vent run

(see Table 1)

Wall thickness is measured from the back standoffs to the inside mounting

surface of termination cap. Create a level surface to mount the vent terminal.

The Terminal must not be recessed into siding. Measure the wall thickness.

Flat Wall Installation

Wall Thickness

(inches)

Vent Length Required

(inches)

4" - 5-1/2" 6"

7" - 8-1/2" 9"

10" - 11-1/2" 12"

9" - 14-1/2' 11" - 14-5/8" Adj. Pipe

15" - 23-1/2" 17" - 24" Adj. Pipe

Adj.Pipe Length

Rigid Pipe Adapter

90 Elbow

Pipe Length

Vent reducer

(Part #946-606)

Powervent Kit

(Part #946-535)

Table 1

CB40EPV Gas Fireplace

City Series Power Vent

919-920 10.11.18

CV40EPV / CB40EPV / CC40EPV

Gas Power Vent Installation CV40EPV / CB40EPV / CC40EPV - Rigid Vent

BX Cable

(sold separately)

Rigid Pipe Adaptor

(Required,sold sepa-

rately)

Frame Assembly

(included w/Power Vent kit)

Power Vent Terminal

(946-535)

Slip Section

(sold separately)

The Power Vent System is a Direct Vent Te rminal designed to allow installation of gas appliances where typical vent conﬁgurations cannot be achieved.

These installation instructions must be used in conjunction with the appliance and appropriate Power Vent components installation instructions.

120 Volt power supply is required to operate this system.

946-535 Power Vent Kit with Vent Terminal

1 510-994 Rigid Pipe adaptor sold separately

1Power Vent Fan included w/Power Vent kit

1Power Vent Frame included w/Power Vent kit

1 911-250/P 45' 5-wire BX cable or sold separately

1 911-251/P 90' 5-wire BX cable sold separately

amount required

for install

4" x 6-5/8" Rigid Pipe sold separately

1 946-535 Power Vent Kit sold separately

Models Equipped with Sureﬁre Ignition

The Power Vent system can only be used with units that have been tested with the Regency Power Vent system.

Downward vertical vent runs are permitted with the Sureﬁre Ignition system. See vent conﬁguration in unit manual.

4" x 6-5/8" Rigid pipe lengths

(sold separately)

Power Vent trim

(incl. with Power V ent

kit)

Power Vent frame

(adjustable depth)

(incl. with Power V ent

kit)

Power vent trim

Power vent frame

CB40EPV Shown

GAS POWER VENT INSTALLATION CB40EPV - RIGID VENT

CB40EPV Gas Fireplace

City Series Power Vent

919-920 10.11.18

CV40EPV / CB40EPV / CC40EPV

Gas Power Vent Installation CV40EPV / CB40EPV / CC40EPV - Flex Vent

BX Cable

(sold separately)

Frame Assembly

(included w/Power Vent kit)

Power Vent trim

(incl. with Power V ent

kit)

Power Vent frame

(adjustable depth)

(incl. with Power V ent

kit)

The Power Vent System is a Direct Vent Te rminal designed to allow installation of gas appliances where typical vent conﬁgurations cannot be achieved.

These installation instructions must be used in conjunction with the appliance and appropriate Power Vent components installation instructions.

120 Volt power supply is required to operate this system.

946-535 Power Vent Kit with Vent Terminal

2 Max. 946-756 20' Flex Kit sold separately

1Power Vent Fan included w/Power Vent kit

1Power Vent Frame included w/Power Vent kit

1 911-250/P 45' 5-wire BX cable or sold separately

1 911-251/P 90' 5-wire BX cable sold separately

1 946-535 Power Vent Kit sold separately

Models Equipped with Sureﬁre Ignition

The Power Vent system can only be used with units that have been tested with the Regency Power Vent system.

Downward vertical vent runs are permitted with the Sureﬁre Ignition system. See vent conﬁguration in unit manual.

Max. 2 x 20' Flex kits (946-756)

(sold separately)

Power Vent Terminal

(946-535)

Power vent trim

Power vent frame

CV40EPV Shown

GAS POWER VENT INSTALLATION CB40EPV - FLEX VENT

CB40EPV Gas Fireplace

Inhaltsverzeichnis

Andere Regency Kamin im Innenbereich Handbücher

Regency

Regency Panorama P33E-NG11 Bedienungsanleitung

Regency

Regency Panorama PG33NG4-R Kurzanleitung

Regency

Regency Horizon HZ30E-NG1 Kurzanleitung

Regency

Regency Panorama P121 Kurzanleitung

Regency

Regency Grandview G600C Kurzanleitung

Regency

Regency Gas Insert E21-NG3 Kurzanleitung

Regency

Regency P33CE-NG Kurzanleitung

Regency

Regency L540EB Kurzanleitung

Regency

Regency Liberty L900-1 Bedienungsanleitung

Regency

Regency City Series Kurzanleitung

Regency

Regency City CV50E DIRECT VENT Kurzanleitung

Regency

Regency Z2510L Kurzanleitung

Regency

Regency R90 Bedienungsanleitung

Regency

Regency G51-NG UltraGlow Kurzanleitung

Regency

Regency Cardinia F150B-1 Kurzanleitung

Regency

Regency U20-NG Bedienungsanleitung

Regency

Regency U31-NG3 Kurzanleitung

Regency

Regency GCI60 Bedienungsanleitung

Regency

Regency Horizon HZ42STE-NG Kurzanleitung

Regency

Regency City Series New York 72 Bedienungsanleitung

Regency

Regency GEM54-NG Bedienungsanleitung

Regency

Regency E18-NG Bedienungsanleitung

Regency

Regency E21-NG10 Kurzanleitung

Regency

Regency L390E-NG1 Kurzanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung