Regency Energy U31 Kurzanleitung

908-005 01/08/09

Owners &

Installation

Manual

Tested by:

Warnock Hersey

& AGA

FORYOURSAFETY

What to do if you smell gas:

!Do not try to light any

appliance

!Donottouchanyelectri-

cal switch: do not use

anyphoneinyourbuild-

ing.

!Immediately call your

gas supplier from a

neighbour's phone.

Follow the gas suppli-

er'sinstructions.

!Ifyou cannotreachyour

gassupplier,callthefire

department.

WARNING:

Improper installation, adjustment,

alteration, service or maintenance

can cause injury or property dam-

age. Refer to this manual. For

assistanceoradditionalinformation

consultanauthorizedinstaller,serv-

ice agency or the gas supplier.

FORYOURSAFETY

Donotstoreorusegasolineorother

flammable vapours and liquids in

thevicinityofthisoranyotherappli-

ance.

Installationandservicemustbeper-

formed by an authorized installer,

service agency or the gas supplier.

U31/I31 GAS INSERT

ZERO CLEARANCE KIT

KIT # 410-905

PLEASE KEEP THESE INSTRUCTIONS

FOR FUTURE REFERENCE

2U31/I31 Gas Insert Zero Clearance Kit

TABLE OF CONTENTS

GAS INSERT ZERO CLEARANCE KIT

CONTENTS PAGE

Listings & Code Approvals ................................................... 3

Specifications ........................................................................ 3

General Information .............................................................. 3

Parts ...................................................................................... 3

Clearances to combustibles .................................................. 4

Locating Your Fireplace ...................................................... 5

Ashlip..................................................................................... 5

Ashlip Installation .................................................................. 6

Framing ................................................................................. 6

Kit Assembly ......................................................................... 7

Venting (Flueing) ................................................................... 8

Optional Outside Combustion Air Supply Installation ........... 9

Gas supply line ..................................................................... 9

Electrical Supply .................................................................... 9

Faceplate & Trim Installation .............................................. 10

Finished Facing Notes ........................................................ 11

U31/I31 Gas Insert Zero Clearance Kit

Specifications

INSTALLATION

LISTINGS AND CODE APPROVALS

This gas component has been tested in accordance with National Safety Standards, and has been certified by Warnock Hersey

for installation and operation in the United States and Canada as described in these Installation and Operating Instructions.

This gas component has also been tested in accordance with AG103 and certified in Australia by the Australian Gas Association

for installation in Australia, and New Zealand. Install according to AG 103 and as described in these installation and operating

instructions.

PARTS

IncludedwithKit:

1 (410-905) Main Body Assembly

Sold Separately: (Rq)=Required (Op)=Optional

(Rq) 1 (410-906) Zero Clearance Faceplate44" W x 32"H

(1117mm W x 813mm H) includes 4"(102mm) Hearth

Trim and faceplate trim

(Op) 1(410-920) Ash Lip

GENERAL INFORMATION

This kit consists of factory built parts that require minimal

assembly to form the Zero Clearance enclosure for the U31/

I31 Gas Insert. The enclosure can then be fixed into a framed

combustible construction, and a standard

"B-vent" (Australia/New Zealand: an approved twin skin flue)

installed on the assembly for the required venting (flueing).

The insert can be installed later.

The faceplate will normally overlap on top of the finished

wall.Using Kit# 410-905 you can convert the U31/I31 Gas

Insert models into highly efficient heat producing Zero Clear-

ance Fireplaces.

Check with your local

building code agency

before you begin your

installation to ensure

compliance with local

codes, including the

need for "permits" and

follow-up inspections. If

any problems are en-

countered regarding

codeapprovals,or if you

wish clarification on any

of the instructions con-

tainedhere,contactyour

local dealer.

4U31/I31 Gas Insert Zero Clearance Kit

INSTALLATION

Top View

**Max. width of 1"(25mm) at 1"(25mm) from surround, calcu-

late depth at 45oas shown in the diagram.

DKK

Max.

Side View

CLEARANCES TO COMBUSTIBLES

The clearances for the Zero Clearance Kit are 0" to combustibles (back, side and floor) but when planning your installation

review the clearances required for the Insert (see below) after it is installed in the Zero Clearance Kit. The Zero Clearance Kit

mustbe installedona flat,solid,continuous surface(e.g. wood, metal,concrete). Thismaybe thefloor,or raisedup on aplatform

to enhance its visual impact.

NOTE: The specified '0' inch floor clearance means that the top surface of the flooring material, i.e. carpeting, tile, etc.,

must not extend above the bottom edge of the 4" Hearth Trim.

Clearances to Combustibles for Insert

*Combustible Mantel Clearances

Depth (Mx) Clearance (My)

(inches) (mm) (inches) (mm)

0" to 3.5" 0mm to 89mm 20" 508mm

to 5.5" to 140mm 21" 533mm

to 12" to 305mm 22" 559mm

From Unit

Sides A 10" / 250 mm

DropCeiling B 47.5" / 1207 mm

12" Mantel* C(My) 22" / 555 mm

From Surround

Sides D 2" / 50 mm

DropCeiling E 37.75" / 945 mm

Max. Mantel Depth* G(Mx) 12" / 305 mm

Max. Alcove Depth H 36" / 882mm

Min. Alcove Width J 48" / 1200 mm

Facing (Mantel Leg)

Side** K 1" / 25 mm

Top L 1" / 25 mm

* Mantel clearances vary with the width of the mantel see

the chart "Combustible Mantel Clearances" on this page.

Note: A non-combustible mantel may be installed at a

lower height if the framing is made of metal studs

covered with a non-combustible board.

U31/I31 Gas Insert Zero Clearance Kit

Figure 3

Figure 1 Figure 2

INSTALLATION

LOCATING YOUR U31/I31 FIREPLACE

Due to high temperatures the Insert should be located out of traffic and away

from furniture and draperies. Provide a minimum of 48" (1220mm) front

clearance to the unit.

This appliance is Listed for bedroom installations when used with a Listed

Millivolt Thermostat. Some areas may have further requirements, check local

codes before installation.

This unit is not approved for installation into a mobile home.

ASH LIP FOR FLUSH INSTALLATION

a) An ashlip is mandatory on a U31/I31 Flush (flat window) Insert when installed less than 6" (152mm), (including the

4"(102mm) Hearth Trim) to a combustible floor (see Figure 1). For detailed installation see Faceplate and Trim Installation.

Note: If the ashlip is required with the Flush Front installed, the bottom Gold Trim will NOT fit and cannotbe installed.

b) No ashlip is required when U31/I31 Insert is raised by 2"(51mm). See figure 2.

c) No ashlip is required on a U31/I31 Insert with a Bay Window and/or Bay Louvers. See figure 3.

a) Cross Corner d) Island

b) Room Divider e) Flush with Wall

c) Flat on wall f) Flat on Wall

Corner

6U31/I31 Gas Insert Zero Clearance Kit

INSTALLATION

FRAMING

1) The trim kit allows for 1/2" (13 mm) of finish facing material. The kit may be installed directly on and/or against standard

combustible building materials.

2) Frame in the enclosure for the Kit with framing material. The framed opening for the assembled kit is 31.75" (806mm)

high x 37.75" (959mm) wide x 19.5" (495mm) (20" (508mm) including drywall) deep. See diagram below.

3) For exterior walls, vapour barrier and insulate the enclosure to the same degree as the rest of the house, or according

to local installation codes.

4) The appliance may be enclosed above the standoffs on the cabinet but the clearances stated on the "B-vent" chimney

must be maintained.

ASHLIP INSTALLATION

1) Line up the two holes in the ashlip with the bottom 2 holes in the front of the stove.

2) Screw into position with the two screws provided with the ashlip.

NOTE:The bottomgoldtrimdoesnotgoonto

the unit when the ashlip is installed.

U31/I31 Gas Insert Zero Clearance Kit

KIT ASSEMBLY

INSTALLATION

Diagram 2

Diagram 3

Diagram 1

1) Using the screws provided, attach left and right sides to

the rear panel. Side flanges go on the outside. See

diagram 1.

2) Install floor. All floor flanges go on the inside. See

diagram 1.

3) Install top assembly. Make sure top rear flange is on the

outside of the back panel. Top side flanges go on the

inside.

4) Install top front standoff assembly, with the drywall stand-

off angle facing forward. See diagram 1.

5) Move Zero Clearance Assembly into final position and

attach to framing. See diagram 3.

6) Attach 4"(100mm) -"B" vent adapter. See Venting.

Note: Topinsulationprotrudesabout

1"(25mm) in order to assure a

tight seal when faceplate is

installed. Leakage in this area

willresultinpossibleoverheat-

ingofthefinishingmaterialim-

mediatelyabovetheframe.See

diagram 1.

8U31/I31 Gas Insert Zero Clearance Kit

INSTALLATION

Variable Chimney Routes

VENTING (FLUEING)

Note: The draft hood must be installed parallel to the

fireplace opening, as shown below. See Instruc-

tions in U31/I31 Installation Manual.

Install stove insert as per U31/I31 Installation Manual.

1) This fireplace must be vented (flued) with a 4" (100mm)

diameter Class “B” vent (Australia/New Zealand: twin

skin flue). The installation of the venting (flueing) system

must conform and be in accordance with the natural gas

installationcodeCAN/CGA-B149(Canada),ANSIZ223.1

(U.S.A.), AG 601 (Australia), and NZS 5261 (New Zea-

land). Minimum chimney height from base of fireplace

must be at least 12 feet (3.6m).

2) MasonryChimneyInstallation:

This application can be connected to a masonry chimney

flue. Makesurethe masonrychimneyis cleanandin good

working order. When an existing masonry chimney is

unlined and local experience indicates that gas conden-

sation may be a problem or if local codes dictate, an

approved liner should be installed. Use “B” Vent (flue) to

bridge the gap between the fireplace and the masonry

chimney. To ensure proper flue sizing and operation it is

recommended that the masonry chimney be lined with an

approved aluminium chimney liner of the same diameter

as the “B” Vent (flue). Make sure connection between “B”

Vent (flue) and masonry is completely sealed. Flue pipe

exposed to cold air should be insulated in a chase. If

condensation occurs, a trap should be installed at bottom

of flue.

Use a maximum of two off-

sets; four 45oelbows, or two

90oelbowsforexample. Slope

horizontal pipe at least 1/4"

(6.4 mm) rise per foot of run.

Horizontal runs should not

exceed the vertical rise. Keep

horizontal runs to a minimum.

See chart below.

NOTE: ColdClimateInstallation

When this appliance is to be in-

stalled against a non-insulated

wall or in a chase, fibreglass insu-

lation should be installed around

the body of the fireplace.

U31/I31 Gas Insert Zero Clearance Kit

INSTALLATION

ELECTRICAL

OUTLET BOX

OPTIONAL OUTSIDE COMBUSTION AIR SUPPLY

-NORTH AMERICAN INSTALLATIONS

A 4" (100 mm) dia. aluminum flex pipe or equivalent may be installed from the outside (with a proper exterior cover) to the Zero

Clearance cabinet. There are outside holes provided on three sides of the kit. Use only the one that is most suitable for your

installation. This will provide adequate outside combustion air supply to the heater.

GAS SUPPLY LINE

An authorized service person should install the gas line in accordance with all local building codes. If codes permit, flex gas

line or coiled copper tubing may be used as gas supply line. The suggested way to install the gas supply line is as follows:

run 1/2" (9.5 mm) NPT gas line to the left side of the framed opening. (See U31/I31 installation instructions for additional

information).

Specifications

Min. Inlet Input

Gas Pressure Rating

Natural Gas 5" w.c. 30,000 Btu/h

1.13 kPa 31 mj/h

Propane 12" w.c. 27,500 Btu/h

2.75 kPa 28.5 mj/h

ELECTRICAL SUPPLY

Provide 120 VAC, 60 Hz (in Australia and New Zealand: 240 VAC, 50 Hzin) receptacle within 24"(610mm) of the left side of the

appliance (not inside the Zero Clearance Cabinet). Plug the cord on the appliance into the receptacle.

10 U31/I31 Gas Insert Zero Clearance Kit

ON/OFF

Switch

Fan Speed

Switch

(Rear View)

Wires to

Fan Switch

Connectors

Self-adhesive

Wire Clip

For Gas

Connection

Wires to

On/Off

Switch

POWER CORD (3ft)

Diagram 3

INSTALLATION

Diagram 1: Faceplate Assembly

Trim

Clips

Diagram 2: Trim Assembly

FACEPLATE & TRIM INSTALLATION

3) Using the trim clips provided, join the left side trim (with

the ON/OFF switch) to the top trim. See diagram 2.

Connect the right side trim to the top trim.

4) Place the trim on the assembled faceplate panels, align-

ing the wire connections from the switches with the notch

on the left side panel.

5) Connect the fan switch wires by taking the black and red

wires with the male ends (in the grey harness) and

connect them with the wire connectors from the fan speed

control.

6) Connect the ON/OFF switch wires by taking the black and

red wires with the female ends and connect them to the

ON/OFF switch.

7) Install these wires in the clips on the left faceplate to

ensure they dont touch the insert. See diagram 3.

1) Lay the faceplate panels flat, facedown on something soft

so they don't scratch.

2) a) Take the top faceplate and align the holes in it with

the holes in the side panels. Using the screws

provided,attachfrom thetopofthepanel (holesinthe

top panel are slightly larger than the holes in the side

panel to facilitate easier installation). See diagram 1.

b) 4"(102mm)HearthTrim.AttachtheHearthTrimtothe

bottom of the faceplate side panels with the screws

provided. See diagram 1.

Hint: Don't tighten the screws down completely at this

point, do a trial fit to the unit. Make any necessary adjust-

ments and when it fits properly then tighten down the

screws.

8) The power cord should be run behind the faceplate panel

from the U31/I31 to electrical outlet box.

Andere Handbücher für Energy U31

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Regency Kamin im Innenbereich Handbücher

Regency

Regency classic i2400m Kurzanleitung

Regency

Regency U31-NG and Bedienungsanleitung

Regency

Regency L676S-LP1 Sunrise Bedienungsanleitung

Regency

Regency classic i2400m Service-Handbuch

Regency

Regency liberty LRI3E Kurzanleitung

Regency

Regency L540PB Service-Handbuch

Regency

Regency Energy E18E Kurzanleitung

Regency

Regency F5102 - AUSTRALIA Kurzanleitung

Regency

Regency IG34 Kurzanleitung

Regency

Regency I100B-1 BERWICK Kurzanleitung

Regency

Regency Excalibur P90E Zero Kurzanleitung

Regency

Regency Horizon HZ30E-NG10 Kurzanleitung

Regency

Regency Cardinia F150B-1 Kurzanleitung

Regency

Regency P36-NG4 Kurzanleitung

Regency

Regency FPI FP90 Kurzanleitung

Regency

Regency I1200 Kurzanleitung

Regency

Regency City Series Kurzanleitung

Regency

Regency Horizon HZ30E-NG1 Kurzanleitung

Regency

Regency City CP60E Kurzanleitung

Regency

Regency Panorama P33CE Kurzanleitung

Regency

Regency Panorama P121 Kurzanleitung

Regency

Regency P121-NG2 Kurzanleitung

Regency

Regency Alterra F175B-1 Kurzanleitung

Regency

Regency FireGenie PG121-NG1 Kurzanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung