Regency Gi29L Series Bedienungsanleitung

Gi29L Gas Insert | 1

Minimum Fireplace Dimensions

The minimum replace clearances and dimensions for the Regency gas insert are shown in the following diagrams.

Regency®Gi29L Gas Insert

MODEL Gi29L-NG Gi29L-LP

Fuel Type Natural Gas Propane

Minimum Supply Pressure 5” W.C. (1.25 kPa) 11” W.C. (2.74 kPa)

Manifold Pressure - High 3.8” W.C. (0.94 kPa) 10.5” W.C. (2.62 kPa)

Manifold Pressure - Low 1.1” W.C. (0.27 kPa) 2.9” W.C. (0.72 kPa)

Orice Size -Altitude 0-4500 ft #38 DMS (0-2000 ft.)

#39 DMS (2000 - 4500 ft.) #52 DMS

Min. Input (0-2000 ft.)

Min. Input (2000-4000 ft.)

17,000 Btu/h (4.98 kW)

16,500 Btu/h (4.83 kW) 17,000 Btu/h (4.98 kW)

Maximum Input (0-2000 ft.)

Maximum Input (2000-4500 ft.)

31,500 Btu/h (9.22 kW)

30,500 Btu/h (8.93 kW) 31,500 Btu/h (9.22 kW)

Vent Sizing 3” (76 mm) x 3” (76 mm)

Co-linear (Standard)

3” (76 mm) x 3” (76 mm)

Co-linear (Standard)

CPA P.4.1 63.88% 62.33%

Letter Description Dimensions

(inches)

Dimensions

(mm)

AWidth 29-3/4" 756 mm

B Outerbox Width 28-5/16" 719 mm

C Outerbox Height 20-1/4" 514 mm

D Outerbox Depth 17-7/8" 454 mm

EOuterbox Rear Width 20" 508 mm

FFront to Top Taper 8-3/8" 213 mm

G Front to Side Taper 3-13/16" 97 mm

H Rear to Side Taper 14-1/16" 357 mm

IGas Inlet Height 1-1/4" 32mm

JGas Inlet Rear Depth 5-1/2" 140 mm

KGas Inlet Front Depth 12-7/16" 316 mm

LElectrical Access Height 1-1/8" 29 mm

M Electrical Access Rear Depth 7-1/2" 191 mm

NElectrical Access Front Depth 10-3/8" 264 mm

OGlass Viewing Area Width 24-1/8" 613 mm

PGlass Viewing Area Height 15" 381 mm

QFront to Intake 15-1/16" 383 mm

R Front to Exhaust 14" 356 mm

S Intake Diameter 3" 76 mm

TExhaust Diameter 3" 76 mm

2 | Gi29L Gas Insert

Faceplate Dimensions

Three-Sided Faceplate

Four-Sided Faceplate

Faceplate

Dimensions

Width

(A)

Height

(B)

Depth

(C)

Bottom Height

(D)

Regular Faceplate 40-3/16" (1021 mm) 26" (660 mm) 1-1/4" (32 mm) -

Regular Faceplate w/ Premium

Surround

40-13/16" (1021 mm) 26-3/8" (670 mm) 1-11/16" (43

mm)

Flush Faceplate 40-3/16" (1021 mm) 26" (660 mm) 1/8" (3 mm) -

Flush Faceplate w/ Traditional

Surround

45-3/4" (1162 mm) 28-3/4" (730 mm) 2-1/4" (57 mm) -

4-Sided Flush Faceplate 40-3/16" (1021 mm) 29-1/4" (743 mm) 1/8" (3 mm) 4-3/16" (106 mm)

Finishing Trim 31-7/8" (810 mm) 21-7/8" (556 mm) 1/16" (2 mm) -

4-Sided Finishing Trim 31-7/8" (810 mm) 23-1/8" (587 mm) 1/16" (2 mm) 1-1/8" (29 mm)

Oversized Backing Plate 47-1/2" (1207 mm) 31-1/2" (800 mm) 1/8" (3 mm) -

3-Sided Custom Backing Plate 33-7/8" - 56-7/8"

(860 mm - 1445 mm)

22-7/8" - 44-7/8"

(581 mm - 1118 mm)

1/8" (3 mm) -

4-Sided Custom Backing Plate 33-7/8" - 69"

(860 mm - 1753 mm)

25-1/8" - 45"

(638 mm - 1143 mm)

1/8" (3 mm) 2-1/8" minimum (54 mm min.)

Gi29L Gas Insert | 3

Diagram 1

Minimum Clearances to Combustibles

The clearances listed below are minimum distances unless otherwise stated.

A major cause of res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this decorative

gas appliance is installed only in accordance with these instructions.

J***

Clearance: Dimension Measured From:

A: Sidewall 8" / 203 mm ***From inside edge of faceplate / doors

B: Ceiling 63-3/4" / 1873 mm From base of unit

D: Min. Hearth Depth 12" / 305 mm Not required if unit raised 3" (76 mm) o the oor.

E: Min. Hearth Length 36"/ 914 mm Not required if unit raised 3" (76 mm) o the oor.

J*** 27-1/4" / 692 mm inside edge of the faceplate/doors - reference only.

K: Min. Alcove Width 54" / 1372 mm

L: Max. Alcove Depth 36" / 914 mm From the front of the unit.

M: Mantel Deector 2-1/2"/ 89 mm*

NOTES

• A 36” (914 mm) wide x 12” (305 mm) deep, non-combustible hearth

is required in front of the appliance unless the unit is raised 3” (76 mm) o the oor.

• *An optional 2-1/2" (64 mm) mantel deector reduces the mantel height to 13" (330 mm) from top of the unit @ 1" (25 mm) depth.

• (J): *** Measurement from the faceplate edge or doors - for reference only: 27-1/4’’ (692 mm)

4 | Gi29L Gas Insert

10"

12"

14"

16"

18"

20"

22"

24"

12"

10"

26"

28"

30"

Top of

fireplace

opening

A12" (305 mm)

B 22-1/2" (572 mm)

C 19-1/2" (495 mm)

D 6" (152 mm)

Mantel Clearances Without Mantel Deector

Diagram 2

E1-1/2 " (38 mm)

F16-1/2" (419 mm)

G Non Combustible Materials

H 19-3/4" (451 mm) to base of unit

WARNING

• Although this appliance passes safety certication, the hearth

in front of the replace becomes very hot when the replace

heats. Do not use the hearth as a seat or shelf.

Gi29L Gas Insert | 5

Diagram 3

Mantel Clearances with 2-1/2" (64 mm) Mantel Deector

NOTES

• A 2-1/2" (64 mm) mantel deector reduces mantel height to 13" (330 mm)

from the bottom of the unit at 1" (25 mm) depth.

• A noncombustible mantel may be installed at a lower height if the framing is

made of metal studs covered with a non-combustible board. The noncombustible

mantel, when installed at a lower overall height, may not be lower than 6"

(152 mm) from the top of the replace opening.

• All material used must be non-combustible.

A12" (305 mm)

B 22" (559 mm)

C 17-1/2" (445 mm)

D 6" (152 mm)

E1" (25 mm)

F13" (330 mm)

G Non Combustible

H 19-3/4" (451 mm) to base of unit

10"

12"

14"

16"

18"

20"

22"

24"

10"

12"

26"

28"

30"

Top of

fireplace

opening

Deflector

6 | Gi29L Gas Insert

Minimum Fireplace Opening Sizes with Varying Faceplate/Backing Plate Options

Faceplate

Dimensions

Minimum Install

Width

(A)

Minimum Install

Height

(B)

Minimum Install

Depth

(C)

Minimum Rear

Width

(D)

Taper

Depth

(E)

Regular Faceplate 28-7/16" (722 mm) 20-1/4" (514 mm) 16-11/16" (424 mm) 20" (508 mm) 2-13-16" (71 mm)

Regular Faceplate w/ Backing Plate 30-7/8" (784 mm) 21-7/16" (545 mm) 16-3/4" (425 mm) 20" (508 mm) 2-11/16" (68 mm)

Regular Faceplate w/ Premium Surround 28-7/16" (722 mm) 20-1/4" (514 mm) 16-5/8" (422 mm) 20" (508 mm) 2-9/16" (65 mm)

Regular Faceplate w/ Premium Surround

and Backing Plate

30-7/8" (784 mm) 21-7/16" (545 mm) 16-1/2" (419 mm) 20"(508 mm) 2-7/16" (62 mm)

Flush Faceplate 30" (762 mm) 21-1/16" (535 mm) 17-15/16" (456 mm) 20" (508 mm) 3-7/8" (98 mm)

Flush Faceplate w/ Backing Plate 30-7/8" (784 mm) 21-7/16" (545 mm) 17-13/16" (452 mm) 20" (508 mm) 3-3/4" (95 mm)

Flush Faceplate w/ Traditional Surround 28-7/16" (722 mm) 20-1/4" (514 mm) 15-15/16" (405 mm) 20" (508 mm) 1-7/8" (48 mm)

Flush Faceplate w/ Traditional Surround

and Backing Plate

30-7/8" (784 mm) 21-7/16" (545 mm) 15-13/16" (402 mm) 20" (508 mm) 1-3/4" (45 mm)

4-Sided Flush Faceplate 30" (762 mm) 21-5/16" (541 mm) 17-15/16" (456 mm) 20" (508 mm) 3-7/8" (98 mm)

Finishing Trim 30" (762 mm) 21-1/16" (535 mm) 18" (457mm) 20" (508 mm) 3-15/16" (100 mm)

Finishing Trim w/ Backing Plate 30-7/8" (784 mm) 21-7/16" (545 mm) 17-7/8" (454 mm) 20" (508 mm) 3-7/8" (98 mm)

4-Sided Finishing Trim 30" (762 mm) 21-5/16" (541 mm) 18" (457 mm) 20" (508 mm) 3-15/16" (100 mm)

Gi29L Gas Insert | 7

Using Steel Studs and Concrete Board Over Masonry Brick Fireplace

The masonry front brick facing can be removed and replaced with non-combustible materials such as steel studs and concrete board/durarock/micor

board as per diagram 1, only if safe to do so. Steel stud may also be placed in front of the masonry brick if left in place. This is the preferred method

depending on the condition of the masonry brick replace.

The opening between the front of the masonry rebox and non-combustible materials such as steel studs must be sealed so heat cannot run between

the face of the wood replace and the refacing materials. Only nishing materials such as tile, stone, brick, or similar materials that are non-combustible

may be used. Use materials that are uniform so that when the unit is positioned, there are no visible gaps on the sides or top of the surround.

NONCOMBUSTIBLE FACING OVER

COMBUSTIBLE FRAMING

DIMENSIONS

HORIZONTAL CLEARANCE - A

VERTICAL CLEARANCE - B

23"

OPENING WIDTH - C

30 1/4" MIN

OPENING HEIGHT - D

21 1/2" MIN

NONCOMBUSTIBLE FACING OVER

NONCOMBUSTIBLE FRAMING

DIMENSIONS

A - Horizontal clearance 8" (203 mm)

B - Vertical clearance 23" (584 mm)

C - Opening Width 30-1/4" min. (768 mm)

D - Opening Height 21-1/2" min. (546 mm)

E - Minimum Total Width 46-1/4'' (1175 mm)

F - Minimum Total Height 41-3/4'' (1060 mm)

Combustible Facing Over

Combustible Framing

Non-Combustible Facing Over

Non-Combustible Framing

Diagram 1

Existing Masonry Fireplace

Combustible material permitted

Non-combustible

material only

8 | Gi29L Gas Insert

Gas Connection

Vertical Venting

THE APPLIANCE MUST NOT BE CONNECTED TO A

CHIMNEY FLUE SERVING A SEPARATE SOLID FUEL

BURNING APPLIANCE.

This appliance is designed to attach to two 3" (76 mm) co-linear aluminium

ex running the full length of the chimney. The ue length must be a

minimum of 8' (2.44 m) and a maximum of 35' (10.7 m) long. See the

chart below for minimum distances from the roof. Periodically check that

the vent is unrestricted.

Masonry chimneys may take various contours which the exible liner will

accommodate. However, keep the exible liner as straight as possible (avoid

unnecessary bending).

Attach both the exhaust and intake ue liners to both the termination cap

& ue collar at the appliance with a minimum of three self-tapping screws.

Use Mil-Pac sealant to seal the pipes.

The air intake pipe must be attached to the inlet air collar of the termination

cap.

1. If the appliance is installed into an existing chimney system, thoroughly

clean the masonry or factory-built replace.

2. The appliance has an opening on the left side of the control compartment.

A 3/8" NPT gas supply pipe must be brought near the opening.

3. Locate the centerpoint where the vent will pass through the chimney,

above the appliance. Move the appliance to the installation location.

Ensure that the insert is level.

4. Do not cut any sheetmetal parts of the replace into which the gas

insert will be installed.

5. If the factory-built replace has no gas access hole(s), drill one of 1-1/2"

(37-1/2 mm) or less though the lower sides or bottom of the rebox.

The access hole must be plugged with non-combustible insulation after

the gas supply line is installed.

Gas & Electrical Connections

NOTES

• When attaching the two 3 inch (51-76 mm) liners to the

termination cap and prior to sliding them down the chimney,

it is good practice to mark the liners "exhaust" & "air intake".

This prevents mixing up the liners at the ue collar connection

of the appliance. If facing the appliance from the front, the air

intake is located on the left and the exhaust ue on the right.

Part # Description

948-305 3" Flex - 35 ft.

946-529 Co-linear DV Vertical Termination Cap

Air

Intake Exhaust

Flue

• This appliance was tested and certied as a com-

plete system with the noted termination caps and

ex liner. Only the listed termination caps/ex liner

noted below can be used. Use of termination caps

or ex liners not listed in this manual will void the

warranty and certication of this appliance. It is

also important not to enclose the termination cap

inside of a masonry chimney rain cap, or similar.

The termination must be exposed on all four sides

and above to exhaust and draw air into the rebox.

IMPORTANT

• Only persons licensed to work with gas piping may

make the gas connections to this appliance.

WARNING

Gi29L Gas Insert | 9

Alternate Approved Vertical Termination Caps/Adaptor

Alternate Approved Caps

46DVA-VC Vertical Termination Cap

46DVA-VCH High Wind Cap

AND

46DVA-GK 3" Co-linear Adaptor with ashing

In areas with consistently high winds, we recommend using the Simpson Dura-Vent System (46DVA-GK adapter and 46DVA-VCH high-wind cap).

The air intake pipe must be attached to the inlet air collar of the termination cap.

10 | Gi29L Gas Insert

Vertical Venting / Restrictor Settings for NG and LP

LPNG

Vertical Height (Feet)

Setting #1

Setting #2

Setting #4

Setting #3

2" open

2-1/2" open

1" open Setting #2

2-1/2" open

4-1/2" open

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Regency Kamin im Innenbereich Handbücher

Regency

Regency HZ33CE-NG10 Kurzanleitung

Regency

Regency Panorama PG33NG4-R Kurzanleitung

Regency

Regency HZ54E-NG10 Kurzanleitung

Regency

Regency City CST60E Kurzanleitung

Regency

Regency LIBERTY L676-NG Kurzanleitung

Regency

Regency P121-NG2 Bedienungsanleitung

Regency

Regency Classic i2450 Bedienungsanleitung

Regency

Regency Classic I1200S Kurzanleitung

Regency

Regency City CB72EPV-LP Kurzanleitung

Regency

Regency PG121-NG Kurzanleitung

Regency

Regency I1205S Kurzanleitung

Regency

Regency Panorama PG121NG1-R Kurzanleitung

Regency

Regency City Series Kurzanleitung

Regency

Regency FireGenie PG121-NG1 Kurzanleitung

Regency

Regency IG34-LPG Kurzanleitung

Regency

Regency GR44-3 and Betriebsanleitung

Regency

Regency Excalibur P90 Zero Clearance Kurzanleitung

Regency

Regency H2105 Service-Handbuch

Regency

Regency Ei29 Bedienungsanleitung

Regency

Regency L390PB Kurzanleitung

Regency

Regency P121-NG Kurzanleitung

Regency

Regency U32-LP5 Bedienungsanleitung

Regency

Regency GF900L-NG Kurzanleitung

Regency

Regency Bellavista B36XTE Kurzanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch