Regency Greenfire GF1500L NG-2 Bedienungsanleitung

 GreenreGF1500L-2 |1

Greenre®GF1500L-2 Gas Fireplace

MODEL GF1500L NG-2 GF1500L LP-2 GF1500L ULPG-2

Fuel Type Natural Gas Propane ULPG

Gas Consumption 50MJ/h 49MJ/h 44MJ/h

Manifold

Pressure 0.87kPa 2.49kPa 2.49kPa

Injector Size 1x#29

3.40mm

1x#47

1.99mm

1x#49

1.85mm

1151mm

344mm

1263mm

633mm

249mm

117mm

37mm

159mm

459mm

13mm

737mm

824mm

945mm

560mm

523mm

2| GreenreGF1500L-2

CLEARANCES

Caution Requirements

Thetop,backandsidesofthereplacearedenedby

standos.ThemetalendsofthestandomayNOTbe

recessedintocombustibleconstruction.

WARNING

Fire hazard is an extreme risk

if these clearances (air space) to combustible materials are

not adhered to. It is of greatest importance that this replace

and ue system be installed only in accordance with these

instructions.

The clearances listed below are minimum distances unless otherwise stated:

A major cause of chimney related res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest

importance that this replace and ue system be installed only in accordance with these instructions.

Clearance: Dimension Measured From:

A: Mantel Height (min.) 254mm TopofFireplaceOpening/HotAirOutlet

B: Sidewall (on one side) 152mm SideofFireplaceOpening/HotAirOutlet

C: Ceiling

(room and/or alcove)

1162mm TopofFireplaceOpening/HotAirOutlet

D: Mantel Depth (max.) 305mm 730mmAboveFireplaceOpening/Hot

AirOutlet

E: Alcove Width 1524mm SidewalltoSidewall(Minimum)

F: Alcove Depth 914mm FronttoBackWall(Maximum)

G: From Floor 617mm TopofFireplaceOpening/HotAirOutlet

Note: 0 Nohearthrequired

Installed close

to ceiling.

Flue Clearances to Combustibles

Horizontal-Top 76mm

Horizontal-Side 51mm

Horizontal-Bottom 51mm

Vertical 51mm

Alcove

Installed Close

to Floor

IMPORTANT: If installing a television above

this appliance, the television must be either

fully recessed into the wall above the

replace and or have a mantle below the

television. If the television is left unprotected,

the extreme heat being emitted from this

appliance will result in damage to the

television. See clearance requirements for

both mantle (page 9) and or enclosing the

top of the appliance (page 11 (D) dimension).

GF1500L-2 Gas Fireplace

 GreenreGF1500L-2 |3

FRAMING DIMENSIONS

Framing

Dimensions Description GF1500

A FramingHeight 945mmcombustiblenish

A¹FramingHeight-SteelStud 846mmnoncombustiblesteelstud

B FramingWidth 1394mm

CFramingDepth 568mm

D MinimumHeighttoCombustibles 1225mm

ECornerWallDepth 1460mm

F CornerFacingWallWidth 2065mm

GVentCenterlineHeight 1016mm

H* Non-combustiblefacingheight *seenon-combustiblefacingheightinthismanual

IGasConnectionOpeningHeight 38mm

J GasConnectionHeight 67mm

KGasConnectionInset 44mm

L GasConnectionOpeningWidth 89mm

NOTE:Aminimumthicknessof12mmnon-combustiblefacingboardcompliantwithAS1530-1andAS1530-3isrequired

whenusingthenoncombustibleushnishingoption.Aminimumthicknessof10mm-19mmcombustiblefacingboardis

requiredwhenchoosingthecombustibleushnishingoption.

Note:mustmaintain13mmairgapallaroundtheperimeteroftheappliancewhenchoosingthisoption.

Non-Combustible

Facing

Header

Flex or Rigid Pipe

Drywall or

other facing

Timber

Studs

Finished Floor

Timber

Studs

Finished Floor

Non-combustible Flush Finishing Framing

Steel Stud

on edge

NOTE: Do not place timber

studsbelowthetimberfram-

ing studs already in place.

Additional steel studs must

be added as shown when

choosingthenoncombustible

ushnishingoption.

Note:Steelstudmustbeinstalledafter

unithasbeenpositionedinplaceand

priortoinstallationofnon-combustible

nishing

Note: Ifraisingtheunit,thenthe

minimumframingheightmeasure-

ment(A)mustbeadheredto.

For example: Unit raised 300mm

thenA+300mm=1240mm.

CombustibleushnishingFraming

IMPORTANT NOTE:

This unit can be nished

with combustible facing

material of thickness range

10-19mm OR non-combus-

tible facing material of a

minimum thickness 12mm.

GF1500L-2 Gas Fireplace

4| GreenreGF1500L-2

GF1500L-2 Gas Fireplace

Combustible Requirements

FRAMING & FINISHING (COMBUSTIBLE)

Note:

Dependingonthematerialusedfornishing,thenailingstripsmust

besetaccordinglysothatthenishedmaterialisalwaysbeush

withtheedgeoftheange.

If nishing with material with a combined thickness greater

than 19mm, non-combustible material must be used.

Note:

*Finishing Trim or one of the fascias must be used with

combustible nishing.

10mm to 19mm combustible nishing can be used if the 13mm

airgaparoundthefrontfacingoftheunitismaintained.Finishing

materialcannotbethickerthan19mmandmustbeushwiththe

frontedgeoftheange.

Note:

• The siding nailing strips are factory set at 10mm. The top

nailingstripisxedduringtransittotherearoftheappliance.

• Donotplaceanyreinforcementinfrontofheaderandbehind

nishingmaterial.

• Thenailingstripmustbeused.Itisxedduringtransittothe

rearoftheunit.

NOTE:

Theappliancemustbeinstalledonaat,

solid,continuoussurfaceForexamplea

wood,metalorconcreteoor.Inaraised

(onthe wall) application the appliance

must be installed on a metal or wood

panelextendingthefullwidthanddepth

oftheappliance.

NOTE:

Donotremovethestandoswhichare

locatedaroundtheperimeterothisunit

Theseareinplaceandactasaguidefor

thecombustiblematerialtobeplaced.

148mm

482 mm

1288 mm

630 mm

Finished

Material

10mm-19mmthick-

nessusingcombusti-

blenishing

Note:mustmaintain

13mmairgapall

around

(seediagramsbelow

andonnextpage)

1stslot

Unit

13mm

gap

NOTE: Maintain a 13mm gap

all round.

A minimum of 10mm to

maximum 19mm material

thickness is required.

 GreenreGF1500L-2 |5

GF1500L-2 Gas Fireplace

CLEARANCES FOR COMBUSTIBLE FINISHING WITH MANTEL

Due to the extreme heat this replace emits, the mantel clearances are critical.

Combustiblenishingandmantelclearancesareshowninthediagram

ontheright.FinishingTrimmustbeusedwithcombustiblenishing.

Note: Maximum combustible nishing material thickness is

19mm measured from the front of the replace opening.

If total nishing material is greater than 19mm, non-

combustible must be used.

Note:Ensurethepaintthatisusedonthemantelandthe

facingis"highquality"orthepaintmaydiscolour.

Note:Combustiblemantelstartsat796mm(618mm+178mm)

fromunitbase.

COMBUSTIBLE MANTEL LEG CLEARANCES

Mantelleg&combustiblenishingclearancesasperdiagram:

Combustible Material

(152mm)

(305mm)

(0)

(630 mm)

To unit base

(322 mm)

Top of

Fireplace

Opening

(576 mm)

(305mm)

(470 mm)

(241mm)

Combustible Stud

(On Edge)

Nailing Flange

Combustible facing

(min. 10mm- max. 19mm)

(297 mm)

(200mm)

(100mm)

(372 mm)

Allowable mantel

leg projection

181mm

254mm

330mm

38mm

MANTEL LEG

102mm

178mm

Allowable mantel

leg projection

181mm

254mm

330mm

38mm

MANTEL LEG

102mm

178mm

Allowable mantel

leg projection

181mm

254mm

330mm

38mm

MANTEL LEG

102mm

178mm

13mm Gap 13mm Gap

Combustible Combustible

Important:

6| GreenreGF1500L-2

CLEARANCES FOR NON-COMBUSTIBLE FLUSH FINISHING WITH MANTEL

Due to the extreme heat this replace emits, the

mantel clearances are critical.

Combustiblemantelclearancesfromtopoffrontfacingare

showninthediagramontheright.

Note:Foraushednishusingnon-combustiblenishing,

seven13mm stand-otabs aroundthereplace opening

mustbebrokeno.Thetopnailingangecannotbeused

andanon-combustiblesteelstudmustbeinstalledtosupport

thenon-combustiblefacing.

Note: Ensure the paint that is used on the

mantel and the facing is "high quality"

or the paint may discolour.

Note:Combustiblemantelstartsat796mm(605mm

+191mm)fromunitbase.

NON COMBUSTIBLE MANTEL LEG CLEARANCES

Mantelleg&Non-combustiblenishingclearancesasperdiagram:(FlushedFinish)

Allowablemantel

leg projection

181mm

254mm

330mm

38mm

MANTELLEG

102mm

178mm

Allowablemantel

leg projection

181mm

254mm

330mm

38mm

MANTELLEG

102mm

178mm

Allowablemantel

leg projection

181mm

254mm

330mm

38mm

MANTELLEG

102mm

178mm

83mm

Non-combustible

83mm

Non-combustible

Combustible Material

(152 mm)

(305mm)

(0 mm)

To Uni

Base

(617 mm)

(335 mm)

Top of

Fireplace

Opening

(589mm)

(305 mm)

(457 mm)

(254mm)

Non-Combustible facing (min.12 mm)

Non-Combustible steel stud

846 mm to underside

of steel stud

(100mm)

(310 mm)

(200mm)

(385 mm)

GF1500L-2 Gas Fireplace

 GreenreGF1500L-2 |7

GF1500L-2 Gas Fireplace

NON COMBUSTIBLE REQUIREMENTS

FLUSHED FINISHING & FRAMING WITH NON-COMBUSTIBLE MATERIAL

Note: Forush nishing,thetop nailing stripmustbe removedand a

non-combustiblesteelstudsupportadded.

Thesevenreplaceopeningstandoswhicharelocatedonthisunitcan

beremovedwhennoncombustiblematerialisinstalledushwiththeunit.

(seeP.13).

Non-combustiblenishingmaterialonthetopandsidesmustalsobeused.

NOTE:

Theappliancemustbeinstalledon

aat,solid,continuoussurfaceFor

exampleawood,metalorconcrete

oor. In a raised (on the wall)

applicationtheappliancemustbe

installedonametalorwoodpanel

extendingthefullwidthanddepth

oftheappliance.

871 mm

605 mm

1432 mm

Non-combustible

Combustible

Steel Stud

on edge

Timber Stud

159 mm 446 mm

Non-Combustible

Material

Combustible

Material

Finished

Material

*diagramsshownbelow

arewithtopnailingstrip

removed.

12mm

25mm

38mm

Unit

Unit MINIMUM THICKNESS OF THE FINISH MATERIAL: 12MM

A minimum thickness of 12mm

non-combustible facing is required.

8| GreenreGF1500L-2

OPTIONAL FRAMING KIT

920-194 01/28/20

OPTIONAL FRAMING KIT

1. Construct the timber framing, ensure inside dimensions are 1095 mm H

x 1394 mm W as shown below.

NN

NN

2. Bend both side nailing strips from the side of the appliance until

positioned as shown below. Determine the overall combined thickness

of the non-combustible board + ﬁnished material being used. The

nailing strips can be adjusted up to 38mm. Remove top nailing strip and

recycle.

3. Adjust the nailing strips by loosening 2 screws on each nailing strip -

adjust and retighten screws.

NOTE: depending on the ﬁnishing material used.

4. Attach both vertical studs (607-065) to the vertical timber studs and

secure using 6 screws, as shown.

NOTE: Ensure the ﬂat side of the steel stud is facing the timber framing.

(607-065)

Flat side out

5. Secure horizontal steel header stud (606-067) with 2 screws per side as

per diagram.

6. Slide the unit into position. Hook up gas, ﬂueing, electrical and

conversion kit (if purchased) prior to installing the remaining steel studs.

7. Secure the upper horizontal steel stud (606-067) as shown with 2

screws per side.

8. Secure the top large horizontal stud (607-027) with 2 screws per side

as shown. Bring ﬁnishing material to the edge of the top framing lip on

large stud (607-027).

9. Install the large lower stud (607-066) with 2 screws on each side.

Header stud

(606-067)

606-067

607-065

607-027

607-066

607-065

Nailing Strips

Remove Top

Nailing Strip

Large stud

(607-027)

Large stud

(607-066)

Horizontal stud

(606-067)

tooltip

Framing Lip

Finishing with

non combustible

material

Use Top Holes

Finishing with

combustible material

Use lower holes

GF1500L-1

GF1500L-2 Gas Fireplace

 GreenreGF1500L-2 |9

GF1500L-2 Gas Fireplace

FRAMING & FINISHING (CLEAN FINISH INSTALLATIONS ONLY)

Note: When constructing the framed opening, please ensure there is access to install the gas lines when the unit is

installed.

2. Forexteriorwalls,insulatetheenclosuretothesamedegreeastherestofthehouse,applyvapourbarrieranddrywall,asperlocalinstallation

codes.(Do not insulate the replace itself and/or the ueing. Clearances must be maintained as per this manual.)

WARNING: Failure to insulate and add vapor barriers to the inside of the exterior wall will result in operational and performance

problems including, but not limited to: excessive condensation on glass doors, poor ame package, carbon, blue ames etc. These

are not product related issues.

3. Theunitdoesnothavetobecompletelyenclosedinachase.Youmustmaintainclearancesfromtheuetocombustiblematerials:See"Clearances"

section.Combustiblematerialscanbelaidagainstthesideandbackstandosandtheappliancebase.

4. Non-combustiblematerial(ie.tile,slate,etc)maybebroughtuptoandoverlaptheunit(topandbottom)ensuringthatthemaximumthickness

doesnotgobeyondthe38mmasshowninthediagrambelow.Thefaceplatewillnotbeabletobemountedifnishedmaterialisbeyond38mm.

1. Frameintheenclosurefortheunitwithframingmaterial.

IMPORTANT: The framed opening must be of non-combustible material.

Ensure  front of facing material is

ushwiththeedgeoftheangeon

thereplace.

10 | GreenreGF1500L-2

FLUEING INTRODUCTION

TheGF1500Lusesthe"balancedue"technologyCo-Axialsystem.Theinnerlinerventsproductsofcombustiontotheoutsidewhiletheouterliner

drawsoutsidecombustionairintothecombustionchambertherebyeliminatingtheneedtouseheatedroomairforcombustionandlosingwarmroom

airupthechimney.

Note: These ue pipes must not be connected to any other appliance.

Thegasapplianceanduesystemmustbeventeddirectlytotheoutsideofthebuilding,andneverbeattachedtoachimneyservingaseparatesolidfuel

orgasburningappliance.Eachdirectventgasappliancemustuseit'sownseparateuesystem.Commonuesystemsareprohibited.

FLUEING ARRANGEMENT FOR HORIZONTAL TERMINATIONS

Thediagramshowsallallowablecombinationsofverticalrunswithhorizontalterminations,usingone90o(two45o elbowsequalone90oelbow).

Note: Must use optional rigid pipe adapter (Part# 770-994) when using Simpson Dura Vent Only.

• Maintain clearances to combustibles as listed in "Clearances" section

• Horizontal ue must be supported every 0.9m

• A ue guard should be used whenever the termination is lower than the specied minimum or as per local codes.

• Flex system can only be used up to 3m - otherwise rigid system must be used.

FLUE RESTRICTOR SETTING:

Flue restrictor factory set at Set 0.

Refertothe"FlueRestrictorPosition"sectionfordetailsonhowtochangetheuerestrictorfromthefactorysettingofSet0toSet1ifrequired.

1061 mm

Minimum

Height

Requirement

Restrictor Set #0

Full Open

Restrictor Set #1

44 mm-Open

6.0

6.5

Meters

4.0

4.2

Restrictor Set #2

41 mm-open

GF1500L-2 Gas Fireplace

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Regency Kamin im Innenbereich Handbücher

Regency

Regency H2100 Kurzanleitung

Regency

Regency HZ33CE-NG Kurzanleitung

Regency

Regency City CV50E DIRECT VENT Kurzanleitung

Regency

Regency GF900L-NG Kurzanleitung

Regency

Regency Panorama PG121 Kurzanleitung

Regency

Regency I2403M Kurzanleitung

Regency

Regency City Series Kurzanleitung

Regency

Regency GF900C-NG1 Bedienungsanleitung

Regency

Regency Liberty Gas Fireplace L676-NG1 Kurzanleitung

Regency

Regency Liberty LRI4E series Kurzanleitung

Regency

Regency P36-LPG4 Kurzanleitung

Regency

Regency HZ54E-NG10 Kurzanleitung

Regency

Regency Cascades I1500 Kurzanleitung

Regency

Regency Energy E18E-NG11 Kurzanleitung

Regency

Regency City Series New York 40 Bedienungsanleitung

Regency

Regency L850B Kurzanleitung

Regency

Regency I3100 Montageanleitung

Regency

Regency Panorama P121 Kurzanleitung

Regency

Regency LRI6E-NG Kurzanleitung

Regency

Regency P42-LP3 Kurzanleitung

Regency

Regency Panorama P33-10 Kurzanleitung

Regency

Regency U32-LP5 Bedienungsanleitung

Regency

Regency Liberty LRI4E series Kurzanleitung

Regency

Regency ACC40LENG Kurzanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch