Reliable G4 Bedienungsanleitung

Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523

Bulletin 171 January 2020

Model G4 XLO-QR ECLH/ECOH

Quick-Response Extended Coverage

K11.2 (160 metric)

Concealed Pendent (SIN R7146)

Quick-Response for Light Hazard and

Ordinary Hazard occupancies

Spacing up to 20ft x 20ft (6.1m x 6.1m)

Features

1. Extended Coverage protection to 400 ft2

(37.2 m2) per sprinkler.

2. Nominal K-factor of 11.2 (160 metric).

3. Ordinary temperature rated - 165°F (74°C).

4. Flat cover plate with ½ inch (13 mm) assem-

bly adjustment.

5. Smooth aesthetic ceiling profile.

6. Cover plate available in a wide variety of

colors and finishes.

7. Cover plate does not require clips or springs.

Approvals

1. Listed by Underwriters Laboratories, Inc.

and certified by UL for Canada (cULus).

UL Listing Category

Sprinklers, Automatic and Open Extended Coverage Sprin-

klers-Light Hazard and Ordinary Hazard Occupancy UL

Guide Number – VNIV.

Product Description

The Reliable Model G4 XLO-QR ECLH/ECOH Concealed

sprinkler is an Extended Coverage Sprinkler for use in Light

Hazard and Ordinary Hazard occupancies with a coverage

area of up to 400 square feet (37.2 m2) per sprinkler.

The use of extended coverage sprinklers can provide lower

installation costs by requiring fewer sprinklers, less piping and

reduced labor. The larger K-factor 11.2 (160 metric) provides

for reduced pressures to achieve the required flow compared

with smaller K-factor sprinklers.

The G4 XLO-QR ECLH/ECOH can eliminate the need for

precise cutting of drop nipples. The Push-on/Thread-off cover

plate assembly provides up to 1/2” (13 mm) of adjustment to

allow the cover to fit accurately against the ceiling. The fire

protection system need not be shut down when adjusting or

removing the Push-on/Thread-off cover plate assembly.

G4 XLO-QR ECLH/ECOH Concealed

Design Criteria

G4XLO-QR ECLH/ECOH sprinklers are to be installed ac-

cording to the design criteria shown in this Bulletin, NFPA 13,

and all other local codes and ordinances. Flows and pres-

sures, as shown in the Flow Requirements chart on page 2

of this Bulletin, must be selected based on the spacing and

hazard classifications.

The following criteria also apply:

• Minimum sprinkler spacing is 9 ft (2.75 m).

• Sprinklers have a minimum flow requirement for each

spacing as shown in the Flow Requirements chart on

page 2.

• Sprinklers are only to be used in systems hydraulically

designed per NFPA 13.

• Deflector to commodity clearance shall be a minimum

of 18 inches (457 mm).

• Sprinklers shall be installed in unobstructed construc-

tion as defined in NFPA 13.

• Sprinklers can be installed under a sloping ceiling not

exceeding 2 inches (50.8 mm) of rise in 12 inches

(304.5 mm).

• Maximum working pressure is 175 psi (12.1 bar) at the

sprinkler.

G4 XLO-QR ECLH/ECOH Concealed Pendent

Technical Data

Sprinkler

Model Type

Nominal

K-factor

Temperature

Rating

Max.

Ceiling

Temp.

Maximum

Sprinkler

Spacing

ft (m)

Maximum

Coverage

Area

ft2(m2)

Thread

Size Approvals

gpm/psi1/2

(lpm/bar1/2)°F °C °F °C

G4 XLO-QR

ECLH/ECOH

Concealed

Pendent 11.2 (160) 165 74 100 38 20 (6.1) 400 (37.2)

¾”NPT

ISO 7-1 R3/4

cULus

Flow Requirements - Quick Response

Spacing

ft (m)

Coverage

Area

ft2(m2)

Light Hazard Ordinary Hazard Group 1 Ordinary Hazard Group 2

Flow

gpm (lpm)

Pressure

psi (bar)

Flow

gpm (Lpm)

Pressure

psi (bar)

Flow

gpm (lpm)

Pressure

psi (bar)

14 x 14 (4.3 x 4.3) 196 (18.2) 30 (113.5) 7.2 (0.5) 30 (113.6) 7.2 (0.5) 39 (147.6) 12.1 (0.8)

16 x 16 (4.9 x 4.9) 256 (23.8) 30 (113.5) 7.2 (0.5) 39 (147.6) 12.1 (0.8) 51 (193.0) 20.7 (1.4)

18 x 18 (5.5 x 5.5) 324 (30.1) 33 (125.0) 8.7 (0.6) 49 (185.5) 19.1 (1.3) 65 (246.0) 33.7 (2.3)

20 x 20 (6.1 x 6.1) 400 (37.2) 40 (151.0) 12.8 (0.9) 60 (227.1) 28.7 (2.0) 80 (302.8) 51.0 (3.5)

Installation

Do not install the MODEL G4

XLO-QR ECLH/ECOH in ceilings

which have positive pressure in

the space above. After installa-

tion, inspect all sprinklers to en-

sure that both the gap between

the cover plate and ceiling and

the 4 drive slots in the cup are

open and free from any air flow

impediment.

After a 25

8” (67 mm) diameter

hole is cut in the ceiling, the

Maintenance

Model G4XLO-QR ECLH/ECOH sprinklers should be in-

spected and maintained in accordance with NFPA 25. Do

not clean sprinklers with soap and water, ammonia or any

other cleaning fluids. Remove dust by using a soft brush

or gentle vacuuming. Replace any sprinkler or cover plate

assembly, which has been painted (other than factory ap-

plied) or damaged in any way. A stock of spare sprinklers

should be maintained to allow quick replacement of dam-

aged or operated sprinklers. Prior to installation, sprin-

klers should be maintained in their original cartons and

packaging until used to minimize the potential for damage

to sprinklers that would cause improper operation or non-

operation. Once operated automatic sprinklers and cover

plates cannot be reassembled and reused. New sprin-

klers of the same size, type and temperature rating must

be installed. A cabinet of replacement sprinklers should

be provided for this purpose.

Model G4 Wrench

sprinkler is to be installed with the Model G4 Wrench.

When installing a sprinkler, the wrench is first positioned

into the sprinkler/cup assembly until two wrench tangs

fully engage drive slots in the top of the cup. The sprin-

kler is then tightened into the pipe fitting. When inserting

or removing the wrench from the sprinkler/cup assembly

care should be taken to prevent damage to the sprin-

kler. DO NOT WRENCH ON ANY OTHER PART OF THE

SPRINKLER/CUP ASSEMBLY.

A protective cap is provided to protect the drop down

deflector from damage which could occur during con-

struction before the cover plate is installed. The cap is

factory installed inside the sprinkler cup. Remove the

cap to install the sprinkler, then replace the cap until the

cover plate is installed.

THE MODEL G4 XLO-QR ECLH/ECOH SPRINKLER

MUST BE INSTALLED ONLY WITH A 135°F RATED

MODEL G4/G5 COVER PLATE WHICH HAS BEEN

LISTED WITH THE SPRINKLER.

DRIVE SLOT

(TYP. of 4)

Model Model G4XLO-QR ECLH/ECOH Con-

cealed Pendent Sprinkler Specification

Sprinklers shall be a cULus listed as Quick-Response

Extended Coverage sprinklers for Light Hazard, Ordinary

Hazard Group 1, and Ordinary Hazard Group 2 occupan-

cies. Sprinklers to be of bronze frame construction with brass

cover plate and copper alloy retainer flange assembly. Water

seal assembly shall consist of a PTFE coated Belleville spring

washer and machined brass cup containing no plastic parts.

Method of attaching the cover plate to the sprinkler cup shall

be a Push-on and Thread-off design allowing a 1/2” (13 mm)

cover plate adjustment. Sprinklers shall have a nominal K-

factor of 11.2 (160 metric), and 3/4” NPT threads. Sprinkler

temperature rating shall be 165°F (74°C) with a cover plate

temperature rating of 135°F (57°C). Sprinklers shall be ca-

pable of a maximum coverage area of 20 ft. x 20 ft. (6.1 m x

6.1 m), with a minimum horizontal spacing of 9 ft. (2.75 m).

Rated working pressure shall be 175 psi (12.0 bar). A plastic

protective cap shall be provided and factory installed onto

the sprinkler cup to protect the sprinkler prior to installation of

the cover plate. Cover plate type: G4/G5. Cover plate finish:

[White] [Chrome] [Custom Finish–specify]. Quick-Response

Extended Coverage Concealed Pendent Sprinklers for Light

Hazard and Ordinary Hazard Occupancies shall be Reliable

Model G4XLO-QR ECLH/ECOH. SIN R7146 (Bulletin 171).

Ordering Information

Specify:

1. Sprinkler Model: G4XLO-QR ECLH/ECOH (SIN

R7146)

2. Cover Plate Finish: [See Cover Plate Finishes chart]

3. Cover Plate Type: Model G4/G5

4. Thread Size: 3/4” NPT unless otherwise specified,

ISO 7-1 R3/4 available by special order

The installation wrench is Model G4.

Sprinkler Identification Number (SIN): R7146

Cover Plate Finishes

Standard Finishes

White Paint

Chrome

Special Application

Finishes

Off White Paint

Black Paint

Custom Color Paint – Specify(1)

Raw Brass (Lacquered)

Bright Brass

Finished Bronze

Satin Chrome

Stainless Steel Clad(2)

(1) Custom color paint is semi-gloss, unless specified otherwise.

(2) Stainless steel clad cover plates are Type 316 Stainless Steel on the

finished side and C102 Copper Alloy on the back side. Cover plates

are not listed or approved as corrosion resistant.

Note: Paint or any other coatings applied over the factory fin-

ish will void all approvals and warranties.

Fig. 1 - Sprinkler and Cover Plate Dimensions

Reliable Automatic Sprinkler Co., Inc.

(800) 431-1588 Sales Offices

(800) 848-6051 Sales Fax

(914) 829-2042 Corporate Offices

www.reliablesprinkler.com Internet Address

Manufactured by

Recycled

Paper

Revision lines indicate updated or new data.

EG. Printed in U.S.A. 01/20

The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, Factory

Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable.

Products manufactured and distributed by Reliable have been protecting life and property for almost 100 years.

P/N 9999970465

Fig. 2 - Installation Dimensions

Andere Handbücher für G4

Dieses Handbuch passt für folgende Modelle

Andere Reliable Bewässerungssystem Handbücher

Reliable

Reliable F1-300 Bedienungsanleitung

Reliable

Reliable F1FR28 Series Bedienungsanleitung

Reliable

Reliable DD56-6 Handbuch

Reliable

Reliable F1S5 Series Bedienungsanleitung

Reliable

Reliable JL-14 Bedienungsanleitung

Reliable

Reliable F1FR 300 QREC Handbuch

Reliable

Reliable F1 LO Handbuch

Reliable

Reliable F156 Series Handbuch

Reliable

Reliable G5-80 Bedienungsanleitung

Reliable

Reliable G6-56 Bedienungsanleitung

Reliable

Reliable HL22 Handbuch

Reliable

Reliable G Series Handbuch

Reliable

Reliable The Non-Ferrous Concealer F4FR-NF Bedienungsanleitung

Reliable

Reliable RFC56 Bedienungsanleitung

Reliable

Reliable XL Handbuch

Reliable

Reliable MBEC-14 Handbuch

Reliable

Reliable XL Bedienungsanleitung

Reliable

Reliable GFR VELO–ECOH Handbuch

Reliable

Reliable DH56 HSW-PL Bedienungsanleitung

Reliable

Reliable RFC30 Bedienungsanleitung

Reliable

Reliable F3QR80 Series Bedienungsanleitung

Reliable

Reliable F1FR-SS Series Bedienungsanleitung

Reliable

Reliable F1-28 Series Bedienungsanleitung

Reliable

Reliable F156 Series Bedienungsanleitung

Beliebte Bewässerungssystem Handbücher anderer Marken

Hunter

Hunter Institutional Series Bedienungsanleitung

Cellfast

Cellfast 52-305 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL A Bedienungsanleitung

Oral Care Technologies

Oral Care Technologies Hydro Floss Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Gem F892 Bedienungsanleitung

Netafim

Netafim NETBEAT Bedienungsanleitung

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Bedienungsanleitung

Tyco

Tyco CC3 Bedienungsanleitung

OpenSprinkler

OpenSprinkler OSPi Bedienungsanleitung

EINHELL

EINHELL GE-WW 5537 E Bedienungsanleitung

Valley

Valley Bender160 Bedienungsanleitung

Toro

Toro 730 Series Kurzanleitung

Eden

Eden 97063-EDAMZ Bedienungsanleitung

Tyco

Tyco TY-L Series Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL ELO-231 Bedienungsanleitung

Johnson Controls

Johnson Controls tyco ESFR-17 Bedienungsanleitung

Victaulic

Victaulic VicFlex I-VICFLEX.AQC-U Bedienungsanleitung