Remington 482 Bedienungsanleitung
Important :
Read this manual and all labels carefully before operating your powder actuated tool.
Thismanualshouldalwaysaccompanythetoolandbetransferredwithituponchange
of ownership.
REMINGTON®
Operating
Instructions
Model 482
Powder Actuated
Fastening Tool
REMINGTON
2
106088
INDEX
Warning: Safety Precautions............................................................................. 2-11
Why a Fastener Holds.......................................................................................... 12
Selecting Fasteners and Power Loads ................................................................ 13
Operation ....................................................................................................... 14, 15
Maintenance......................................................................................................... 16
Troubleshooting ............................................................................................. 16, 17
Parts Central ........................................................................................................ 17
Parts List .............................................................................................................. 18
Accessories.......................................................................................................... 19
Tool Disassembly and Assembly ................................................................... 19, 20
Buffer and Piston Replacement ........................................................................... 21
Application Chart............................................................................................ 22, 23
Warranty.................................................................................................Back Cover
* Not provided with tool.
REMINGTON
Power Fastener*
Barrel
Assembly
Trigger
Maximum 2 1/2" - Model 482
Power Load*
Muzzle
Spall Shield
Recommended
Approved Goggles
REMINGTON
Model 482 Powder Actuated Fastening Tools
The Remington Model 482 Powder Actuated Fastening Tool is designed for use
with Remington 22 caliber Type A crimped loads and Remington Power Fasten-
ers. Remington Power Fasteners are manufactured from special steel and heat
treated to produce a very hard yet ductile fastener.
3
106088
Warning: Safety Precautions
The following pages contain detailed warnings, cautions, and rules of safe operation.
Read carefully and become familiar before operating to avoid serious injury. We
expressly disclaim any liability for any injury to persons or damage to property which
result from your failure to take the precautions contained in this manual.
WARNING: Thistoolisdesignedonlyforusebyqualifiedoperators.Qualification
is obtained through a thorough understanding of the Safety Warnings and operating
instructionsasdefinedinthisoperatingmanual.NOTE:Yourlocallaborregulationsmay
require that the operator of this tool on a job site be thoroughly trained and certified for
competencepriortooperatingthistool.Forcertificationprocedures,call1-800-626-2237
(U.S.A.) or 1-905-826-8010 (Canada)
BEFORE USING
DEFECTIVE
3. Operators and bystanders must ALWAYS wear goggles and hearing protection
which meet or exceed the accepted standards for adequate protection in your
country. In the U.S., refer to ANSI standards. In Canada, refer to CSA standards.
2. ALWAYSinspecttomakesurethetoolisworkingproperly.Ifthetooldoesnotwork
properly,removefromserviceandtagDEFECTIVE.DONOTusethetoolagainuntil
it has been properly repaired.
1. ALWAYS handle the tool as if it were loaded. Before starting work, check that the
tool is unloaded and the muzzle is clear. NEVER load a tool unless it is going to be
used.
?
?
4
106088
Safety Precautions
4. ALWAYScleartheworkareaonallsidesandpostappropriatewarningsignsonjob
sites.
5. ALWAYS make sure the work area is clean from loose material and debris.
HANDLING THE TOOL
1. NEVER place your hand over the muzzle. Accidental discharge can cause serious
injury.
2. NEVER place your finger on the trigger until the tool’s muzzle is against the work
surface.
PISTOLETS DE
SCELLEMENT
EN USAGE
ATTENTION
!
5
106088
Safety Precautions
3. ALWAYS store UNLOADED powder actuated tool and power loads in a locked
container. Keep power loads of different power levels in separate containers.
4.NEVER carry or pass a loaded powder actuated tool. NEVER point a powder
actuated tool at anyone.
6. ALWAYS take precaution to maintain your balance while operating a powder
actuated tool.
5. If the tool is dropped, inspect for damage and repair it before continuing to work.
NEVER use a damaged tool.
POWDER
LOADS
POWD
LOAD
6
106088
Safety Precautions
TOO BRITTLE
Surface
shatters
482-30
CENTER
PUNCH TEST
482-27
7. Anoperatortakingmedicationshouldtakeextraprecautionswhilehandlingthetool.
NEVER drink alcoholic beverages or take medications which impair your vision,
balance or judgement before using a powder actuated tool.
1. ALWAYSknowthethicknessandtypeofbasematerialintowhichyouarefastening.
NEVERGUESS.TestthebasematerialbyusingtheCenterPunchTest.TheCenter
Punch Test is performed by using a hammer to test drive the particular power
fastener to be used into the material. If the point penetrates easily, the material is
toosoft.Ifthepointbecomesblunt,thematerialistoohard.Ifthematerialfractures,
cracks or shatters, the material is too brittle. Test fastenings can be made if the
material shows a clear fastener impression and the fastener point is not blunted.
ALWAYSstartwiththelowestpowerload(Gray-Level1)andproceedwiththeorder
shown in the lower right-hand figure above. Always wear approved goggles.
KNOW YOUR FASTENING BASE MATERIAL
TOO HARD
Point
flattens
482-29
TOO SOFT
Sinks in
with
average
hammer
blow
482-28
Start
1
GRAY
3
GREEN 4
YELLOW
2
BROWN
482-31
?
?
?
?
?
?
?
7
106088
482-34
482-37
Safety Precautions
482-36
3. NEVER make fastenings in spalled or cracked areas.
5. DO NOT fasten through or within 1/2" of predrilled or pre-punched holes.
4. NEVER drive power fasteners into thin or easily penetrated materials unless it is
backed by concrete or steel. When in doubt, such as when base material is
concealed, conduct a Center Punch Test (See page 6). Check continually to avoid
fastening into unsuitable material, especially in older buildings.
482-35
CAST IRON GLASS
2.NEVERattempttodrivepowerfastenersintoveryhardorbrittlematerialsincluding,
but not limited to cast iron, glass, tile, stone, brick, or hardened steel. Materials of
this type tend to shatter and create hazard from flying particles.
TILE BRICK
482-33
8
106088
NO
90
482-44
3/16" MIN
1/2" 1"
482-41
6. DO NOT drive power fasteners into concrete less than three times as thick as the
intended fastener penetration, within 3" of the edge, within 3" of another power
fastener or within 3" of a failed power fastener.
7. DO NOT drive power fasteners into steel base material less then 3/16" thick, within
2" of a weld, within 1/2" of the edge or within 1" of another power fastener.
8. Whenfasteningintomasonrywalls,alwaysdriveintohorizontalmortarjoints,never
into vertical mortar joints. BE CAREFUL. A poorly laid joint may permit too much
penetration, and/or unsatisfactory holding power.
OPERATING THE TOOL
1. ALWAYS hold tool perpendicular to work surface.
3" 3"
3"
482-39
TOO THIN
WELD
482-40
3"
3X
1X
482-38
YES
Safety Precautions
9
106088
482-49
30
482-45
4. NEVER use a powder actuated tool in an explosive or flammable atmosphere or
when non-sparking tools are required.
2. Should the tool fail to fire, hold the muzzle firmly against the work surface for 30
seconds. Release the trigger and remove pressure on the tool while holding the
muzzleagainsttheworksurface.Againpressthetoolfirmlyagainsttheworksurface
and pull the trigger. If the tool still fails to fire, hold the tool firmly against the work
surface for another 30 seconds before unloading and carefully discarding the
misfired power load into water or oil.
1. NEVER leave unfired power loads on floors or work surfaces.
POWER
LOADS
POWER LOADS AND FASTENERS
482-47
482-48
3. ALWAYS use the spall shield when driving directly into concrete or steel. Always
wear approved goggles.
GASOLINE
GAS
OLINE
482-50
WATER
POWER
LOADS
Safety Precautions
10
106088
POWER
LOADS
POWER
LOADS
1
2
3
456789
10
11
12
1
22
L
E
K
C
I
N
B
R
A
S
S
482-53
C
A
L
I
B
E
R
POWDER
LOADS
ONLY
482-57
POWER
LOADS
ONLY
2. Remington power loads are available in four power levels with gray (1) being the
lowest power level and yellow (4) being the highest power level. Always start with
the lowest power level (gray-level 1) and increase until a proper fastening is made
(see page 13
Selecting Fasteners and Loads).
Start
1
GRAY
3
GREEN 4
YELLOW
2
BROWN
482-31
Safety Precautions
3. NEVER use power loads in firearms.
4. NEVER carry fasteners or other hard objects in the same pocket or container with
power loads.
5. Acolorblindpersonmusttakeextraprecautionstopreventthechanceofmixingthe
power loads of various levels.
482-58
YELLOW?
BROWN?
GREEN?
GRAY?
NOTE:
Failure to start with
the lowest power
level can result in
overdrive condition
and will result in
damage to tool
(See page 13).
Inhaltsverzeichnis
Andere Remington Elektrowerkzeuge Handbücher
Remington
Remington 496 Bedienungsanleitung
Remington
Remington 489 Bedienungsanleitung
Remington
Remington 500V Bedienungsanleitung
Remington
Remington Power Pro 500V Bedienungsanleitung
Remington
Remington HyperFlex XR1340G Bedienungsanleitung
Remington
Remington 494 Bedienungsanleitung
Remington
Remington RM300-PH Bedienungsanleitung
