MOUNTING PROCEDURE
The ZRC-90 can be mounted to a wall or wooden racks using the two key holes in
the wall bracket.
Notes:
1. The RF reception sensitivity and transmit power are varies depending on the
antenna direction.
2. Before mounting to a wall, be sure to fully read the precautions.
Technical Specifications
Checking Accessories
After opening the cover of the packing box, check that the following accessories
are included.
- ZRC-90 Scene Master - Plastic insert
- Wall mount bracket - Wall anchor x 2pcs
- Screw x 2pcs - User Manual
- Warranty sheet - Scene label sheet
Scene Reference List
(Please write down the scene action in case you need further reference in the
future.)
Create a Secondary Controller
(Copying Network Information to a Secondary Controller)
You can add a secondary controller to your network and copy all of ZRC-90
primary controller's network information to the secondary controller by following
the steps below.
Reset to factory default
ZRC-90 will be excluded from network and restored to factory default setting.
Battery low indication
The unit will detect battery status after key pressed, the LED will flashes 3 times
rapidly then stay off when battery low is detected. Meanwhile, it will report battery
low status to gateway automatically.
In case you need to mount the ZRC-90 into the wall bracket, please be sure to
fully read the following precautions and procedures.
MOUNTING LOCATION PRECAUTIONS
- Before mounting, check the material and structure of the mounting location. If
the location does not have the proper material or structure, the unit can fall and
cause injuries.
- Use commercial items that best match the wall structure and material for the
screws and other fixtures.
- Do not mount near a kitchen counter, humidifier, or other location in which it can
be exposed to smoke or steam. Doing so could cause a fire or electrical shock.
- Do not mount in locations with high humidity or large amounts of dust. Doing so
could cause a fire or electrical shock.
- Do not mount to locations subject to high temperatures, high humidity, or
exposure to water. Doing so could cause a fire or electrical shock.
- Do not mount to locations subject to large amounts of vibration, large jolts, or
large forces. These could cause an injury if the unit falls and breaks.
MOUNTING PROCEDURE PRECAUTIONS
- Do not modify parts or use the unit in ways other than its intended use. Doing
so could cause the unit to fall and result in an injury.
- Be sure to fully check that there are no electrical wires or pipes inside the wall
before mounting.
- If any of the screws are loose, the unit can fall and cause an injury. Do not
mount the unit with the screws still loose.
- Check that the two screws mounted to the wall are fully inserted into the key
holes of the unit. Otherwise, the unit can fall and cause an injury.
- Do not mount the unit so that it sticks out from the wall edge. It could get hit by
people's bodies or objects and cause an injury.
- Supplier will not be liable for any accidents or injuries that occur due to
improper mounting or handling.
- When mounting, be careful not to get your fingers pinched or injure your hands.
Physical Installation
Wireless Information
This device has an open-air line-of-sight transmission distance of 132 feet (40m)
which complies with the Z-Wave standards. Performance can vary depending on
the amount of objects in between Z-Wave devices such as walls and furniture.
Every Z-Wave device set up in your network will act as a signal repeater allowing
devices to talk to each other and find alternate routes in the case of a reception
dead spot.
Radio frequency limitations:
1. Each wall or object (i.e.: refrigerator, bookshelf, large TV, etc) can reduce the
maximum range of 65 feet (20m) by up to 20 to 30%.
2. Plasterboard and wooden walls block less of the radio signal then concrete,
brick or tile walls which will have more of an effect on signal strength.
3. Wall mounted Z-Wave devices will also suffer a loss of range if they are housed
in metal junction boxes which could also reduce the range by up to 20 to 30%.
Maintenance
1 Do not expose your unit to dust, strong sunlight, humidity, high temperatures or
mechanical shocks.
2 Do not use old and new batteries together as old batteries tend to leak.
3 Do not use corrosive or abrasive cleansers on your unit.
4 Keep the unit dust free by wiping it with a soft, dry cloth.
5 Do not disassemble the unit, it contains no user-serviceable parts.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Notice:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the equipment.
Warnings
- Do not modify the unit in any way.
- Risk of fire.
- Risk of electrical shock.
- Risk of burns.
- Do not dispose of electrical appliances and unsorted municipal waste, use
separate collection facilities. Contact your local government for information
regarding the collection systems available.
- There is no user serviceable parts in this unit.
- Use only power supplies listed in the user instructions.
Caution
- Risk of explosion if battery is replaced by an incorrect type.
- Dispose of used batteries according to the instructions.
Model no.
BW8510US (ZRC-90US) BW8510EU (ZRC-90EU)
BW8510AU (ZRC-90AU) BW8510RU (ZRC-90RU)
BW8510IN (ZRC-90IN) BW8510IL (ZRC-90IL)
BW8510JP (ZRC-90JP)
RF frequency
908.42MHz (ZRC-90US) 868.42MHz (ZRC-90EU)
921.42MHz (ZRC-90AU) 869.02MHz (ZRC-90RU)
865.22MHz (ZRC-90IN) 916.02MHz (ZRC-90IL)
922.50MHz (ZRC-90JP)
Blue
up to 132ft (40m) outdoor line of sight, in unobstructed environment
RF operating distance
LED indication
Dry battery AAA x 2pcs
Powered by
20 to 85%, non-condensing
110mm x 70mm x 13.5mm
Humidity
Operation:
Storage:
o
0 to 40 C
o
-20 to 60 C
Temperature
Dimension
60g (main unit and batteries excluded)
15g (wall mount bracket)
Weight:
Setup LED Indication Status
- LED will light up at first 5 seconds
- LED will turn off after 10 seconds
- LED flashes twice then stay off
after reset process completed
Step Setup Key
1Press and keep holding "R" button not less
than 10 seconds.
2Release "R" button then triple click on "R"
button within 2 seconds.
Mount to the
wall bracket
Dis-mount from
wall bracket
121
2
Add/Remove Devices
Adding Device to the Network
Notes:
1. If you can't add your Z-Wave device, this device might have been included in
another Z-Wave network. In this case, please remove this device following the
steps in the [Removing Device from the Network] section then add this device
again.
2. This step can be skipped if the device is already included in the network.
3. In a Z-Wave network, only the primary controller or inclusion controller can add
or include devices into its network. If ZRC-90 is configured as a secondary
controller, it will report "Error" if users attempt to use ZRC-90 to add a device
into its network.
4. If no ACK signal received for more than 30 seconds, the "Add Device" mode will
exit automatically.
Removing Device from the Network
Notes:
1. In a Z-Wave network, only the primary controller or inclusion controller can
remove or exclude devices from its network. If ZRC-90 is configured as a
secondary controller, it will report "Error" if users attempt to use ZRC-90 to
remove a device from its network.
2. If no ACK signal received for more than 30 seconds, the "Remove Device"
mode will exit automatically.
Create a Primary Controller
(Transferring Only Network Information to a New Primary Controller)
You can just transfer network information to another controller so that it will act as
a new primary controller and ZRC-90 will act as a secondary controller. This
primary shift is done by following the steps below.
Step Setup Key
1
Press "L+R" buttons simultaneously until LED
light up to add the device into ZRC-90 Z-Wave
network.
2Press the program button on the target device.
Step Setup Key
1
Click once on "R" button to remove the
device from ZRC-90 Z-Wave network.
2Press the program button on the target
device.
Setup LED Indication Status
LED will keep flashes slowly
LED flashes once then stay off if the
device is included into the network
or
LED flashes 6 times rapidly then stay
off if the operation is invalid
Setup LED Indication Status
LED will keep flashes slowly
LED flashes once then stay off if the
device is excluded from the network
or
LED flashes 6 times rapidly then stay
off if the operation is invalid
Step Setup Key
1Place the two controllers close to each other.
Setup LED Indication Status
-
Setup LED Indication Status
-
LED will keep flashes slowly
LED will flashes slowly until
complete the step of "Create
a Secondary Controller"
Step Setup Key
1Place the two controllers close to each other.
2Press "W + R" buttons simultaneously until LED light up.
3
Please make sure the target secondary controller is
setup to receive information mode. (e.g. target
secondary controller should entry the "Learn mode" if
this is an another ZRC-90. Please refer to the
target controller user manual for more
information)
=> Target secondary controller will act as a secondary
controller after this action.
=> Original ZRC-90 primary controller will still keep in a
primary controller after this action.
Scene Button Action in Single Click Action in Double Click Remark
1
2
3
4
5
6
7
8
F820-8510-0000Printed in China
2Press "W + L" buttons simultaneously until LED light up.
3
Please make sure the target primary controller is setup
to receive information mode. (e.g. target primary
controller should entry the "Learn mode" if this is an
another ZRC-90. Please refer to the target controller
user manual for more information)
=> Target primary controller will act as a primary
controller after this action.
=> Original ZRC-90 primary controller will act as a
secondary controller after this action.
LED will keep flashes slowly
LED will flashes slowly until
complete the step of "Create
a Primary Controller"
