Renesas 9FGV100 Series Bedienungsanleitung

The register descriptions section describes the behavior and function of the customer-programmable non-volatile-memory registers in the

9FGV100x family of clock generators. Table 1 showcases the products under the 9FGV100x family.

For details of product operation, refer to the product datasheet.

9FGV100x Clock Generator Register Set

The device contains volatile (RAM) 8-bit registers and non-volatile 8-bit registers (Figure 1). The non-volatile registers are One-Time

Programmable (OTP) and will be pre-programmed at the factory with a custom dash-code configuration.

The device operates according to settings in the RAM registers. At power-up a pre-programmed configuration is transferred from OTP to

RAM registers. The device behavior can then be modified by reprogramming the RAM registers through I2C.

The device can start up in “I2C mode” or in “Hardware Select Mode”, depending upon the status of the REF0_SEL_I2C# pin at power up.

Also see the datasheet. I2C access is only possible when the device has started up in I2C mode. Startup in I2C mode is default when no

pull-up is added to the REF0_SEL_I2C# pin. Pre-programming settings determine which of the 4 OTP banks is loaded into RAM registers

at power up in I2C mode. Using I2C commands the configuration can be changed and there are also commands to reload a configuration

from a different OTP bank.

Figure 1. Register Maps

User Configuration Table Selection

At power up, the voltage at REF0_SEL_I2C# pin 23 is latched by the device and used to select the state of the SEL0/SCL and SEL1/SDA

pins (Table 2).

When a weak pull up (10k) is placed on REF0_SEL_I2C#, the SEL0/SCL and SEL1/SDA pins will be configured as hardware select

inputs, SEL0 and SEL1. Connecting SEL0 and SEL1 to VDDD and/or GND selects one of 4 configuration register sets, CFG0 through

CFG3, which is then loaded into the non-volatile configuration registers to configure the clock synthesizer. The CFG0 through CFG3

configurations are preprogrammed at the factory according to customer specifications and assigned a specific (dash) part number.

Table 1. 9FGV100x Family Products

Product Description Package

9FGV1001 2 Ref outputs, 4 Diff outputs with 1 Integer output divider 24pins

9FGV1002 2 Ref outputs, 4 Diff outputs with 1 Fractional output divider 24pins

9FGV1004 2 Ref outputs, 2 Diff outputs with individual Integer output dividers

and 2 Diff outputs with 1 Fractional output divider 24pins

User Guide

9FGV100x Register Descriptions and

Programming Guide

9FGV100x Register Descriptions and Programming Guide User Guide

When a weak pull down is placed on REF0_SEL_I2C# (or when it is left floating to use internal pulldown), the pins SEL0 and SEL1 will be

configured as a I2C interface's SDA and SCL slave bus. Configuration register set CFG0 is commonly loaded into the non-volatile

configuration registers to configure the clock synthesizer but the device can be configured to load any of the other configurations. The

host system can use the I2C bus to update the volatile RAM registers to change the configuration, and to read status registers.

I2C Interface and Register Access

When poweredup in I2C mode, the device allows access to internal RAM registers. The default device address is 0xD0 for 8 bits or 0x68

for 7 bits. The device can be preprogrammed for addresses in the range 0xD0-D2-D4-D6 for 8 bits or 0x68-69-6A-6B for 7 bits. The

device acts as a slave device on the I2C bus using one of the four I2C addresses to allow multiple devices to be used in the system. The

interface accepts byte-oriented block write and block read operations. Two address bytes specify the register address of the byte position

of the first register to write or read. Data bytes (registers) are accessed in sequential order from the lowest to the highest byte (most

significant bit first). Read and write block transfers can be stopped after any complete byte transfer. During a write operation, data will not

be moved into the registers until the STOP signal is received, at which point, all data received in the block write will be written

simultaneously in the registers.

For full electrical I2C compliance, it is recommended to use external pull-up resistors for SDATA and SCLK. The internal pull-up resistors

have a size of 100ktypical.

Figure 2. I2C Interface and Register Access

Table 2. Power-Up Setting of Hardware Select Pin vs I2C Mode, and Default OTP Configuration Register

REF0_SEL_I2C# Strap

at Power Up SEL1/SDA pin SEL0/SCL pin Function

10kpullup

0 0 OTPbankCFG0 used to initializeRAMconfigurationregisters

0 1 OTPbank CFG1 used to initializeRAMconfigurationregisters

1 0 OTPbank CFG2 used to initializeRAMconfigurationregisters

1 1 OTPbank CFG3 used to initializeRAMconfigurationregisters

10kpulldown or

floating SDA SCL I2C bus enabled to accessregisters

OTPbank CFG0 used to initializeRAMconfigurationregisters

9FGV100x Register Descriptions and Programming Guide User Guide

Table 3. RAM Overview

Address Function Explanation

0x00 Device / I2C settings

0x01 REF Outputs settings

0x02 OUT3 output settings0x03

0x04

0x05 OUT2 output settings0x06

0x07

0x08 OUT1 output settings0x09

0x0A

0x0B OUT0 output settings0x0C

0x0D

0x0E Crystal Oscillator settings

0x0F

0x10 FOD Spread Spectrum settings

0x11

0x12 FOD Integer Value

0x13 FOD Fractional Value

0x14

0x15 FOD Spread Spectrum settings

0x16

0x17 FOD Miscellaneous0x18

0x19

0x1A PLL Miscellaneous

0x1B

0x1C PLL Loop Filter settings0x1D

0x1E

0x1F PLL Feedback Divider Value

0x20 Integer Output Divider Values0x21

0x22

0x23 Reserved

0x24 Spread Spectrum Jitter Attenuator settings

0x25 Miscellaneous Device settings

9FGV100x Register Descriptions and Programming Guide User Guide

RAM Register Map

Note1: To be able to read this info you already need to know the device address.

Note 2: These two bits show the configuration number 0~3 that will be loaded from OTP into registers at power up. When changing these

bits through I2C you instruct the chip to load another configuration from OTP. This is useful for switching between OTP configurations

when in I2C mode. This method is also used to step through each configuration for reading back OTP contents.

Table 4. RAM Register Map

Decimal Hex

00 0x00 7 Device preprogrammed? 0 = No , 1 = Yes

[6..5] I2C Device address. 00=0xD0 / 0x68, 01=0xD2 / 0x69, 10=0xD4 / 0x6A, 11=0xD6 / 0x6B (1)

[4..2] Reserved

[1..0] Load Configuration number at power up. (2)

01 0x01 [7..6] Enable REF outputs: 0x = Both REF0 and REF1 disabled (unused)

10 = REF0 enabled, REF1 disabled (unused)

11 = Both REF0 and REF1 enabled

5 Reserved

4 Behavior when REF is unused: 0 = Logic “0”, 1 = High Impedance (Tri-State)

[3..2] REF outputs Power Supply Voltage: 00=01=1.8V, 10=2.5V, 11=3.3V

[1..0] Reserved

02 0x02 7 Enable OUT3: 0 = Disabled (unused) , 1 = Enabled

[6..4] OUT3 Configuration: 000 = LPHCSL , Low Power HCSL

001 = CMOS1 , Single ended CMOS on true output pin.

011 = LVDS

100 = CMOS2 , Single ended CMOS on complementary output pin.

101 = CMOSD , Differential CMOS

111 = CMOSP , Two single ended CMOS outputs, in phase

010 and 110 are not used.

[3..2] OUT3 Power Supply Voltage: 00=01=1.8V, 10=2.5V, 11=3.3V

[1..0] Reserved

03 0x03 7 Reserved

6 Behavior when OUT3 is unused: 0 = Logic “0”, 1 = High Impedance (Tri-State)

5 OUT3 LPHCSL Slew Rate Control: 0 = Slow , 1 = Fast

4 OUT3 LPHCSL Impedance Control: 0 = 85Differential , 1 = 100Differential

[3..0] OUT3 LPHCSL Amplitude Control: 650mVpp at 0000 ~ 950mVpp at 1111.

04 0x04 7 Reserved

[6..4] OUT3 LVDS Common Mode Control: 8uA at 000 ~ 11.5uA at 111

3 Reserved

[2..0] OUT3 LVDS Amplitude Control: 30uA at 000 ~ 65uA at 111

9FGV100x Register Descriptions and Programming Guide User Guide

05 0x05 7 Enable OUT2: 0 = Disabled (unused) , 1 = Enabled

[6..4] OUT2 Configuration: 000 = LPHCSL , Low Power HCSL

001 = CMOS1 , Single ended CMOS on true output pin.

011 = LVDS

100 = CMOS2 , Single ended CMOS on complementary output pin.

101 = CMOSD , Differential CMOS

111 = CMOSP , Two single ended CMOS outputs, in phase

010 and 110 are not used.

[3..2] OUT2 Power Supply Voltage: 00=01=1.8V, 10=2.5V, 11=3.3V

[1..0] Reserved

06 0x06 7 Reserved

6 Behavior when OUT2 is unused: 0 = Logic “0”, 1 = High Impedance (Tri-State)

5 OUT2 LPHCSL Slew Rate Control: 0 = Slow , 1 = Fast

4 OUT2 LPHCSL Impedance Control: 0 = 85Differential , 1 = 100Differential

[3..0] OUT2 LPHCSL Amplitude Control: 650mVpp at 0000 ~ 950mVpp at 1111.

07 0x07 7 Reserved

[6..4] OUT2 LVDS Common Mode Control: 8uA at 000 ~ 11.5uA at 111

3 Reserved

[2..0] OUT2 LVDS Amplitude Control: 30uA at 000 ~ 65uA at 111

08 0x08 7 Enable OUT1: 0 = Disabled (unused) , 1 = Enabled

[6..4] OUT1 Configuration: 000 = LPHCSL , Low Power HCSL

001 = CMOS1 , Single ended CMOS on true output pin.

011 = LVDS

100 = CMOS2 , Single ended CMOS on complementary output pin.

101 = CMOSD , Differential CMOS

111 = CMOSP , Two single ended CMOS outputs, in phase

010 and 110 are not used.

[3..2] OUT1 Power Supply Voltage: 00=01=1.8V, 10=2.5V, 11=3.3V

[1..0] Reserved

09 0x09 7 Reserved

6 Behavior when OUT1 is unused: 0 = Logic “0”, 1 = High Impedance (Tri-State)

5 OUT1 LPHCSL Slew Rate Control: 0 = Slow , 1 = Fast

4 OUT1 LPHCSL Impedance Control: 0 = 85Differential , 1 = 100Differential

[3..0] OUT1 LPHCSL Amplitude Control: 650mVpp at 0000 ~ 950mVpp at 1111.

10 0x0A 7 Reserved

[6..4] OUT1 LVDS Common Mode Control: 8uA at 000 ~ 11.5uA at 111

3 Reserved

[2..0] OUT1 LVDS Amplitude Control: 30uA at 000 ~ 65uA at 111

Decimal Hex

9FGV100x Register Descriptions and Programming Guide User Guide

11 0x0B 7 Enable OUT0: 0 = Disabled (unused) , 1 = Enabled

[6..4] OUT0 Configuration: 000 = LPHCSL , Low Power HCSL

001 = CMOS1 , Single ended CMOS on true output pin.

011 = LVDS

100 = CMOS2 , Single ended CMOS on complementary output pin.

101 = CMOSD , Differential CMOS

111 = CMOSP , Two single ended CMOS outputs, in phase

010 and 110 are not used.

[3..2] OUT0 Power Supply Voltage: 00=01=1.8V, 10=2.5V, 11=3.3V

[1..0] Reserved

12 0x0C 7 Reserved

6 Behavior when OUT0 is unused: 0 = Logic “0”, 1 = High Impedance (Tri-State)

5 OUT0 LPHCSL Slew Rate Control: 0 = Slow , 1 = Fast

4 OUT0 LPHCSL Impedance Control: 0 = 85Differential , 1 = 100Differential

[3..0] OUT0 LPHCSL Amplitude Control: 650mVpp at 0000 ~ 950mVpp at 1111.

13 0x0D 7 Reserved

[6..4] OUT0 LVDS Common Mode Control: 8uA at 000 ~ 11.5uA at 111

3 Reserved

[2..0] OUT0 LVDS Amplitude Control: 30uA at 000 ~ 65uA at 111

14 0x0E 7 Crystal Oscillator LDO: 0 = Disabled , 1 = Enabled

6 Reserved

[5..0] Crystal Oscillator X1 pin capacitance: Cap (pF) = 10 + 0.44 * Bits[4..0] + 7.04 * Bit[5]

Appendix 3: Crystal Load Capacitance Registers for Crystal Oscillator Load Capacitance

configuration.

15 0x0F 7 Crystal Oscillator Circuit: 0 = Disabled , 1 = Enabled

6 Reserved

[5..0] Crystal Oscillator X2 pin capacitance: Cap (pF) = 10 + 0.44 * Bits[4..0] + 7.04 * Bit[5]

16 0x10 7 FOD Spread Spectrum: 0 = Disabled , 1 = Enabled

[6..4] Reserved

[3..0] FOD Spread Spectrum Period, bits [11..8]. See Appendix 2 for Spread Spectrum configuration

17 0x11 [7..0] FOD Spread Spectrum Period, bits [7..0]

18 0x12 [7..0] FOD Integer Value. See Appendix 1 for Fractional Divider configuration

19 0x13 [7..0] FOD Fractional Value, bits [15..8]

20 0x14 [7..0] FOD Fractional Value, bits [7..0]

21 0x15 [7..0] FOD Spread Spectrum Step, bits [15..8]

22 0x16 [7..0] FOD Spread Spectrum Step, bits [7..0]

23 0x17 [7..0] Reserved

Decimal Hex

9FGV100x Register Descriptions and Programming Guide User Guide

24 0x18 7 FOD Reset-B: 0 = Hold FOD in Reset Mode , 1 = Release FOD.

Toggle to 0 and back to 1 to apply a reset or restart of the FOD.

[6..2] Reserved

1 FOD Integer Mode: 0 = Use fractional settings for a fractional output divider value.

1 = Run output divider in Integer Mode in case the output division is an integer, for the best

performance.

0 Enable FOD: 0 = FOD is Disabled , 1 = FOD is Enabled.

25 0x19 [7..0] Reserved

26 0x1A 7 PLL, VCO Band Calibration Start. Toggle to 0 and back to 1 to trigger a calibration.

The calibration engages at the moment the bit moves from 0 to 1. The calibration finds the

optimum VCO band for the current VCO frequency.

6 Override VCO Band: 0 = Use Calibrated VCO Band , 1 = Use VCO Band value in bits [5..0].

[5..0] VCO Band Value. See bit 6.

27 0x1B 7 Enable VCO: 0 = VCO Disabled , 1 = VCO Enabled

6 Enable Charge Pump: 0 = CP Disabled , 1 = CP Enabled.

5 Enable PLL Bias: 0 = PLL Bias Disabled , 1 = PLL Bias Enabled

4 Bypass 3rd Pole in Loop Filter: 0 = Use 3rd Pole , 1 = 3rd Pole Bypassed

[3..0] Reserved

28 0x1C [7..4] Loop Filter R-zero value

[3..0] Reserved

29 0x1D [7..0] Reserved

30 0x1E [7..4] Reserved

[3..0] Charge Pump Current

31 0x1F [7..0] PLL Feedback Divider Value.

32 0x20 [7..0] Integer Divider value for OUT3, bits [7..0]

33 0x21 [7..0] Integer Divider value for OUT2, bits [7..0]

34 0x22 [7..4] Integer Divider value for OUT2, bits [11..8]

[3..0] Integer Divider value for OUT3, bits [11..8]

35 0x23 [7..0] Reserved

36 0x24 [7..3] Reserved

2 Spread Spectrum Jitter Attenuator: 0 = Disabled , 1 = Enabled

[1..0] SS Jitter Attenuator configuration. See Appendix 2: Fractional Output Divider and Spread

Spectrum.

Decimal Hex

9FGV100x Register Descriptions and Programming Guide User Guide

37 0x25 7 Reserved

6 Enable Integer Output Dividers: 0 = Disabled , 1 = Enabled

5 Enable Crystal Frequency Doubler: 0 = Disabled , 1 = Enabled

4 Reserved

3 OUT3 Integer Divider Enable: 0 = Disabled , 1 = Enabled

2 OUT2 Integer Divider Enable: 0 = Disabled , 1 = Enabled

[1..0] Reserved

Decimal Hex

9FGV100x Register Descriptions and Programming Guide User Guide

Block Diagrams

Figure 3. 9FGV1004 Block Diagram

Figure 4. 9FGV1002 Block Diagram

Figure 5. 9FGV1001 Block Diagram

Equations

FVCO = FCRYSTAL × Feedback Divider (see register 0x1F)

9FGV1004: FOUT3 = FVCO / Integer Divider 1 (see registers 0x20 and 0x22)

FOUT2 = FVCO / Integer Divider 2 (see registers 0x21 and 0x22)

FOUT0 = FOUT1 = FVCO × JA Multiplier / (2 × FOD) (see registers 0x10 ~ 0x18 and 0x24)

9FGV1002: FOUT0 = FOUT1 = FOUT2 = FOUT3 = FVCO × JA Multiplier / (2 × FOD) (see registers 0x10 ~ 0x18 and 0x24)

9FGV1001: FOUT0 = FOUT1 = FOUT2 = FOUT3 = FVCO / Integer Divider 1 (see registers 0x20 and 0x22)

Limits

FCRYSTAL: 10MHz ~ 40MHz

FVCO: 2300MHz ~ 2600MHz

Integer Divider 1 and 2: 8 ~ 4095

FOD: 4 ~ 255

9FGV100x Register Descriptions and Programming Guide User Guide

Appendix 1: Fractional Output Divider Configuration

The Fractional Output Divider (FOD) is composed of an 8 bit integer portion (address 0x12) and a 16 bit fractional portion (addresses

0x13 and 0x14).

FOD value P = INT(P) + FRAC(P) = FVCO / (2 × FOUT) (1)

FOD Integer [7..0] = DEC2HEX(INT(P)) (2)

The FOD divides the VCO frequency FVCO down to the desired output frequency FOUT. Please note the additional /2 between the VCO

and the FOD.

Convert FRAC(P) to hex with Eq.2 where ROUND2INT means to round to the nearest integer. The round-off error of P in ppm is the

output frequency error in ppm.

FOD Fraction [15..0] = DEC2HEX(ROUND2INT(216×FRAC(P))) (3)

Example: If the VCO is 2500MHz and the desired output frequency is 148.5MHz, the FOD value is 2500/(2×148.5)=8.4175084.

The integer portion is 8 so address 0x12 will be 08-hex.

The fractional portion is 0.4175084.

FOD Fraction [15..0] = DEC2HEX(ROUND2INT(216×0.4175084) = DEC2HEX(ROUND2INT(27361.83))

= DEC2HEX(27362) = 6A E2

Address 0x13 = 6A-hex and address 0x14 = E2-hex.

There is a small error from the rounding. The actual FOD value is 8 + 27362 / 216 = 8.4175110.

The rounding error is 8.4175110 / 8.4175084 - 1 = 0.31ppm.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Renesas Computerhardware Handbücher

Renesas

Renesas R-IN32M4-CL2 TESSERA Montage- und Bedienungsanleitung

Renesas

Renesas R0E53033GCFG90 Bedienungsanleitung

Renesas

Renesas Emulation Pod M306H7T3-RPD-E Bedienungsanleitung

Renesas

Renesas QB-RL78D1A2 Bedienungsanleitung

Renesas

Renesas M3A-HS64 Bedienungsanleitung

Renesas

Renesas 8V19N850 Bedienungsanleitung

Renesas

Renesas IECUBE2 Bedienungsanleitung

Renesas

Renesas IE850A Bedienungsanleitung

Renesas

Renesas HD151TS207SS Bedienungsanleitung

Renesas

Renesas YROTATE-IT-RX62T Bedienungsanleitung

Renesas

Renesas User System Interface Board HS7047ECH61H Bedienungsanleitung

Renesas

Renesas PC7501 Bedienungsanleitung

Renesas

Renesas H8S/2100 Series Bedienungsanleitung

Renesas

Renesas R-IN32M4-CL2 TESSERA Bedienungsanleitung

Renesas

Renesas Compact Emulator M30620T-CPE Bedienungsanleitung

Renesas

Renesas Renesas Synergy AE-CLOUD2 Bedienungsanleitung

Renesas

Renesas MC-COM Bedienungsanleitung

Renesas

Renesas HD74HCT1G66 Bedienungsanleitung

Renesas

Renesas Emulation Probe M30850T2-EPB Bedienungsanleitung

Renesas

Renesas Converter Board R0E521276CFG00 Bedienungsanleitung

Renesas

Renesas Asynchronous SH7145F Montage- und Bedienungsanleitung

Renesas

Renesas M16C/50 Series Bedienungsanleitung

Renesas

Renesas H8SX/1651 Bedienungsanleitung

Renesas

Renesas R0E00030AKCT00 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung