Renesas J80D1 Bedienungsanleitung

Voice over PLC Sample Application

Operating Manual

Rev.2.00 June 25, 2018

www.renesas.com

User’s Manual

Target Device

BCPX3 Evaluation Kit J80D1

All information contained in these materials, including products and product specifications,

represents information on the product at the time of publication and is subject to change by

Renesas Electronics Corp. without notice. Please review the latest information published by

Renesas Electronics Corp. through various means, including the Renesas Electronics Corp.

website (http://www.renesas.com).

General Precautions in the Handling of Microprocessing Unit and Microcontroller Unit Products

The following usage notes are applicable to all Microprocessing unit and Microcontroller unit products

from Renesas. For detailed usage notes on the products covered by this document, refer to the relevant

sections of the document as well as any technical updates that have been issued for the products.

1. Handling of Unused Pins

Handle unused pins in accordance with the directions given under Handling of Unused Pins in

the manual.

⎯The input pins of CMOS products are generally in the high-impedance state. In operation

with an unused pin in the open-circuit state, extra electromagnetic noise is induced in the

vicinity of LSI, an associated shoot-through current flows internally, and malfunctions occur

due to the false recognition of the pin state as an input signal become possible. Unused pins

should be handled as described under Handling of Unused Pins in the manual.

2. Processing at Power-on

The state of the product is undefined at the moment when power is supplied.

⎯The states of internal circuits in the LSI are indeterminate and the states of register settings

and pins are undefined at the moment when power is supplied.

In a finished product where the reset signal is applied to the external reset pin, the states of

pins are not guaranteed from the moment when power is supplied until the reset process is

completed.

In a similar way, the states of pins in a product that is reset by an on-chip power-on reset

function are not guaranteed from the moment when power is supplied until the power

reaches the level at which resetting has been specified.

3. Prohibition of Access to Reserved Addresses

Access to reserved addresses is prohibited.

⎯The reserved addresses are provided for the possible future expansion of functions. Do not

access these addresses; the correct operation of LSI is not guaranteed if they are accessed.

4. Clock Signals

After applying a reset, only release the reset line after the operating clock signal has become

stable. When switching the clock signal during program execution, wait until the target clock

signal has stabilized.

⎯When the clock signal is generated with an external resonator (or from an external oscillator)

during a reset, ensure that the reset line is only released after full stabilization of the clock

signal. Moreover, when switching to a clock signal produced with an external resonator (or

by an external oscillator) while program execution is in progress, wait until the target clock

signal is stable.

5. Differences between Products

Before changing from one product to another, i.e. to a product with a different part number,

confirm that the change will not lead to problems.

⎯The characteristics of Microprocessing unit or Microcontroller unit products in the same

group but having a different part number may differ in terms of the internal memory capacity,

layout pattern, and other factors, which can affect the ranges of electrical characteristics,

such as characteristic values, operating margins, immunity to noise, and amount of radiated

noise. When changing to a product with a different part number, implement a system-

evaluation test for the given product.

 
 
Table of Contents 
Overview.......................................................................................................................1 
Setup ............................................................................................................................2 
1 System configuration .................................................................................................................................2 
2 Hardware setting........................................................................................................................................2 
3 Terminal software setting...........................................................................................................................2 
Operating procedure.....................................................................................................3 
1 Startup screen............................................................................................................................................3 
2 Main menu .................................................................................................................................................3 
3 Call menu...................................................................................................................................................3 
3.1 Simplex.............................................................................................................................................3 
3.2 Duplex..............................................................................................................................................4 
4 Data Send menu........................................................................................................................................4 
5 Setting menu..............................................................................................................................................4 
5.1 Initialization for EEPROM.................................................................................................................4 
5.2 Individual editing for EEPROM.........................................................................................................5 
5.3 Displaying the EEPROM setting value.............................................................................................6 
5.4 Erasing EEPROM setting value.......................................................................................................6 
6 Volume menu.............................................................................................................................................6 
6.1 Changing input volume ....................................................................................................................6 
6.2 Changing output volume..................................................................................................................6 
7 Notes..........................................................................................................................................................6 
State information...........................................................................................................7 
1 Ready state................................................................................................................................................7 
2 Speaking state ...........................................................................................................................................8 
3 Listening state............................................................................................................................................8 
4 Talking state...............................................................................................................................................8 
5 Calling state ...............................................................................................................................................8 
6 Loop back state..........................................................................................................................................9 
 

R11UM0083EJ0200 Rev.2.00 Page 1 of 9

June 25, 2018

RENESAS CONFIDENTIAL

RENESAS Group CONFIDENTIAL

1. Overview

This document is the operating manual, which is descriptive of the Voce over PLC sample application

for BCPX3 Evaluation Kit J80D1. The sample application controls voice communication using the FPAC

API. Refer to "Voice over PLC Software API Specification (R11UM0076EJ0200)" for detail of FPAC API.

Voice over PLC Sample Application Operating Manual 2. Setup

R11UM0083EJ0200 Rev.2.00 Page 2 of 9

June 25, 2018

RENESAS CONFIDENTIAL

RENESAS Group CONFIDENTIAL

2. Setup

2.1 System configuration

In order to communicate using the sample application, two or more J80D1 boards are required. Sample

application is used by connecting J80D1 board and PC with USB Cable. In order to check the sound, it is

necessary to connect a microphone to CN14 of the sender audio board and a speaker to CN16 of the

receiver audio board.

Figure 2-1 system configuration of sample application

2.2 Hardware setting

Set the J80D1 board to use MCU (RX651).

Switches and Jumpers.

Setting

SW1

Turn OFF all the SWs.

SW5

MCU

SW6

USE

Refer to " BCPX3 Evaluation Kit J80D1 User's Manual (R30UZ0098EJ0100)" for other switch and

jumper settings, type of microphone and speaker that can be connected and how to use the J80D1

board.

2.3 Terminal software setting

The sample application is controlled using terminal software. The terminal software settings should be

as follows.

Setting

Value

Baud rate

115200bps

Data

8bit

Parity

None

Stop

1bit

Flow

none

Newline character

CR + LF

J80D1

Power Line

USB Cable

Voice over PLC Sample Application Operating Manual 3. Operating procedure

R11UM0083EJ0200 Rev.2.00 Page 3 of 9

June 25, 2018

RENESAS CONFIDENTIAL

RENESAS Group CONFIDENTIAL

3. Operating procedure

When using the board for the first time, the node ID must be set according to 3.5.2 after startup.

3.1 Startup screen

After power on, CPX3 will be booted automatically and startup screen and main menu will be displayed.

3.2 Main menu

1. Menu to call when starting voice communication.

2. Menu to send binary data.

3. Menu to edit the contents of EEPROM.

4. Menu to change the input and output volume.

When the above menu number is selected, the sub menu shown in chapter 3.3 to chapter 3.5 is

displayed.

3.3 Call menu

User specifies the communication direction in 0.Simplex or 1.Duplex.

3.3.1 Simplex

*********************************************

* Voice over PLC Sample Application Program *

* Ver2.00 [ 1 Sep. 2018] *

*********************************************

Start downloading CPX F/W... successful

---------------------------------------------

- FPAC Ver:0x0200 MAC Ver:0x022706E3 -

- Node ID :000 -

---------------------------------------------

----- Main Menu ( READY ) ----------------

1: Call

2: Data Send

3: Setting

4: Volume

---------------------------------------------

Direction (Simplex:0 Duplex:1)>

---------------------------------------------

Dest Node ID (Ex. 0 1 3...)>

Voice over PLC Sample Application Operating Manual 3. Operating procedure

R11UM0083EJ0200 Rev.2.00 Page 4 of 9

June 25, 2018

RENESAS CONFIDENTIAL

RENESAS Group CONFIDENTIAL

User specifies the destination Node IDs in decimal. If the Node ID is one, unicast transmission is

started, if the Node ID is multiple, multicast transmission is started. When specifying multiple Node IDs,

the user specifies the node IDs separated by spaces.

3.3.2 Duplex

User specifies the destination Node ID in decimal. Only one Node ID is specified.

3.4 Data Send menu

User specifies the destination Node ID in decimal. Only one Node ID is specified.

Continuously, the user sets the sending data in hexadecimal. The maximum data size that can be

transmitted is 64 bytes. Sending data must be entered consecutively without separating.

3.5 Setting menu

1. Menu for initializing EEPROM.

2. Menu for individually editing the set values.

3. Menu for displaying the current set value.

4. Menu for erasing EEPROM.

The sample application reads the initial setting value from EEPROM and starts application process.

When invalid value is written in EEPROM, sample application starts with the default setting value. The

default setting values are follows.

Extend Addr : 0xABCDABCDABCD0000

Node ID : 000

Bitrate : 32000

Sampling Rate : 8000

Modulation : BPSK

3.5.1 Initialization for EEPROM

The value of EEPROM is changed to the default value. The default values are follows.

Extend Addr : 0xABCDABCDABCD0000

Node ID : 000

Bitrate : 32000

Sampling Rate : 8000

Modulation : BPSK

Dest Node ID>

---------------------------------------------

Dest Node ID>

Send Data( 01FF...)>

1: Init config

2: Edit config

3: Disp config

4: Erase config

---------------------------------------------

Voice over PLC Sample Application Operating Manual 3. Operating procedure

R11UM0083EJ0200 Rev.2.00 Page 5 of 9

June 25, 2018

RENESAS CONFIDENTIAL

RENESAS Group CONFIDENTIAL

3.5.2 Individual editing for EEPROM

1. Menu for editing Extended Address.

2. Menu for editing Node ID.

3. Menu for editing Bitrate.

4. Menu for editing Sampling Rate.

5. Menu for editing Modulation

1. Editing Extended Address

64-bit extended address must be set in hexadecimal.

2. Editing Node ID

Node ID from 0 to 127 must be set in decimal.

3. Editing Bitrate

Bitrate must be set in decimal. The settable bit rate is 8000 to 32000.

4. Editing Sampling Rate

Sampling rate must be set in decimal. The settable sampling rate is 8000, 12000 and 16000.

5. Editing Modulation

Modulation must be set in decimal. The settable modulation is 1.BPSK, 2.QPSK and 3.8PSK.

1: Extend Addr

2: Node ID

3: Bitrate

4: Sampling Rate

5: Modulation

---------------------------------------------

Extend Addr(0x0 - 0xFFFFFFFFFFFFFFFF)>

---------------------------------------------

Node ID(0 - 127)>

---------------------------------------------

Bitrate(8000 - 32000)>

---------------------------------------------

Sampling Rate(8000,12000,16000) >

---------------------------------------------

Modulation(BPSK:1 QPSK:2 8PSK:3) >

Voice over PLC Sample Application Operating Manual 3. Operating procedure

R11UM0083EJ0200 Rev.2.00 Page 6 of 9

June 25, 2018

RENESAS CONFIDENTIAL

RENESAS Group CONFIDENTIAL

3.5.3 Displaying the EEPROM setting value

The value set in EEPROM is displayed.

3.5.4 Erasing EEPROM setting value

32bytes from the beginning of EEPROM are initialized with 0xFF.

3.6 Volume menu

1. Menu for change ADC gain.

2. Menu for change DAC gain.

3.6.1 Changing input volume

The ADC gain must be set with signed decimal. The settable gain is -12dB to 20dB.The default value

is -2dB.

3.6.2 Changing output volume

The DAC gain must be set with signed decimal. The settable gain is -63dB to 24dB.The default value

is 0dB.

3.7 Notes

If in the Duplex for voice communication use, please set caller and callee as follows.

1. The sampling rate is 8000Hz.

2. The bitrate 30000bps or less when Modulation is BPSK.

---------------------------------------------

Extend Addr : 0xABCDABCDABCD0000

Node ID : 000

Bitrate : 32000

Sampling Rate : 8000

Modulation : BPSK

---------------------------------------------

1: Input volume

2: Output volume

---------------------------------------------

Volume (-12 to 20)dB >

---------------------------------------------

Volume (-63 to 24)dB >

Inhaltsverzeichnis

Andere Renesas Computerhardware Handbücher

Renesas

Renesas RL78 Series Montage- und Bedienungsanleitung

Renesas

Renesas M16C/62P Group Bedienungsanleitung

Renesas

Renesas HD74LV2GT04A Bedienungsanleitung

Renesas

Renesas CK-RX65N Bedienungsanleitung

Renesas

Renesas PROM Programming Adapter PCA7408 Bedienungsanleitung

Renesas

Renesas H8/3067 Bedienungsanleitung

Renesas

Renesas M-78F0714 Bedienungsanleitung

Renesas

Renesas DA16200 PMOD Bedienungsanleitung

Renesas

Renesas Emulation Pod for M16C/80 Group MCUs... Bedienungsanleitung

Renesas

Renesas HS7125EDB01H Bedienungsanleitung

Renesas

Renesas R0E53036ACFK40 Bedienungsanleitung

Renesas

Renesas RZ/N1S-DB Bedienungsanleitung

Renesas

Renesas RL78G14 Montage- und Bedienungsanleitung

Renesas

Renesas Single-Chip Microcomputer M34519T-MCU Bedienungsanleitung

Renesas

Renesas FP-80Q Bedienungsanleitung

Renesas

Renesas RSKM16C6NK Bedienungsanleitung

Renesas

Renesas R8C/25 Bedienungsanleitung

Renesas

Renesas H8SX/1520 Series Bedienungsanleitung

Renesas

Renesas RSKM32C87 Bedienungsanleitung

Renesas

Renesas M16C/60 Series Bedienungsanleitung

Renesas

Renesas SH7206 Bedienungsanleitung

Renesas

Renesas R0E53032ACSJC0 Bedienungsanleitung

Renesas

Renesas REG10J0052-0200 Bedienungsanleitung

Renesas

Renesas M3T-FLX100-R Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung