Renesas QB-RL78D1A Bedienungsanleitung
User’s Manual
QB-RL78D1A
In-Circuit Emulator
Preliminary User’s Manual
Rev.1.01 2011.6
ZUD-BG-11-0085
Target Devices
RL78/D1A
2
QB-RL78D1A In-Circuit Emulator Preliminary User’s Manual ZUD-BG-11-0085
3
General Precautions for Handling This Product
1. Circumstances not covered by product guarantee
• If the product was disassembled, altered, or repaired by the customer
• If it was dropped, broken, or given another strong shock
• Use at overvoltage, use outside guaranteed temperature range, storing outside guaranteed temperature range
• If power was turned on while connection to the AC adapter, USB interface cable, or target system was in an
unsatisfactory state
• If the cable of the AC adapter, the USB interface cable, the emulation probe, or the like was bent or pulled excessively
• If an AC adapter other than the supplied product was used
• If the product got wet
• If this product is connected to the target system when there is a potential difference between the GND of this product
and GND of the target system.
• If the connectors or cables are plugged/unplugged while this product is in the power-on state.
• If excessive load is applied to the connectors or sockets (As for handling, please see 2.5 Mounting and Connecting
Connectors).
• If a metal part of the power switch, cooling fan, or another such part comes in contact with an electrostatic charge.
• If the product is used or stored in an environment where an electrostatic or electrical noise is likely to occur.
2. Safety precautions
• If used for a long time, the product may become hot (50°C to 60°C). Be careful of low temperature burns and other
dangers due to the product becoming hot.
• Be careful of electrical shock. There is a danger of electrical shock if the product is used as described above in 1.
Circumstances not covered by product guarantee.
• The AC adapter supplied with the product is exclusively for this product, so do not use it with other products.
QB-RL78D1A In-Circuit Emulator Preliminary User’s Manual ZUD-BG-11-0085
4
How to Use This Manual
Readers This manual is intended for users who wish to perform debugging using the QB-
RL78D1A. The readers of this manual are assumed to be familiar with the device
functions and usage, and to have knowledge of debuggers.
Purpose This manual is intended to give users an understanding of the basic specifications and
correct usage of the QB-RL78D1A.
Organization This manual is divided into the following sections.
• General
• Setup procedure
• Settings at product shipment
• Cautions
How to Read This Manual It is assumed that the readers of this manual have general knowledge in the fields of
electrical engineering, logic circuits, and microcontrollers.
This manual describes the basic setup procedures and how to set switches.
To understand the overall functions and usages of the QB-RL78D1A
→Read this manual in the order of the CONTENTS. The mark <R> shows major
revised points. The revised points can be easily searched by copying an “<R>” in the
PDF file and specifying it in the “Find what:” field.
To know the manipulations, command functions, and other software-related settings of
the QB-RL78D1A
→See the user’s manual of the debugger (supplied with the QB-RL78D1A) to be used.
Conventions Note: Footnote for item marked with Note in the text
Caution: Information requiring particular attention
Remark: Supplementary information
Numeric representation: Binary ... xxxx or xxxxB
Decimal ... xxxx
Hexadecimal ... xxxxH
Prefix indicating power of 2
(address space, memory
capacity): K (kilo): 210 = 1,024
M (mega): 220 = 1,0242
QB-RL78D1A In-Circuit Emulator Preliminary User’s Manual ZUD-BG-11-0085
5
Terminology The meanings of the terms used in this manual are described in the table below.
Term Meaning
Target device This is the device to be emulated.
Target system This is the system to be debugged.
This includes the target program and the hardware provided by the user.
IECUBE TM Generic name for Renesas Electronics’ high-performance / compact
in-circuit emulator.
Related Documents Please use the following documents in conjunction with this manual.
The related documents listed below may include preliminary versions. However,
preliminary versions are not marked as such.
Documents Related to Device (User’s Manuals)
Document Name Document Number
RL78/D1A User’s Manual Under development
RL78 Microcontrollers for Instructions User’s Manual Under development
Documents Related to Development Tools (User’s Manuals)
Document Name Document Number
QB-RL78D1A In-Circuit Emulator User’s Manual This manual
Start R20UT0256E
Design R20UT0007E
RL78,78K0R Cording Under development
RL78,78K0R Build Under development
RL78,78K0R Debug Under development
Analysis R20UT0265E
Programming R20UT0266E
CubeSuite Integrated Development
Environment User’s Manual
Message R20UT0267E
Caution The related documents listed above are subject to change without notice. Be sure to use the latest
version of each document for designing, etc.
IECUBE is a registered trademark of Renesas Electronics Corporation in Japan and Germany.
Windows is either registered trademarks or trademarks of Microsoft Corporation in the United States and/or
other countries.
PC/AT is a trademark of International Business Machines Corporation.
QB-RL78D1A In-Circuit Emulator Preliminary User’s Manual ZUD-BG-11-0085
6
CONTENTS
CHAPTER 1 GENERAL.....................................................................................................................................7
1.1 Hardware Specifications .......................................................................................................................8
1.2 Names and Functions of Hardware ......................................................................................................9
1.3 System Specifications.........................................................................................................................11
1.4 System Configuration .........................................................................................................................12
1.5 System Configuration for Each Target Device ...................................................................................14
1.6 Package Contents ..............................................................................................................................15
1.7 AC Adapter for IECUBE......................................................................................................................16
CHAPTER 2 SETUP PROCEDURE................................................................................................................17
2.1 Software Settings................................................................................................................................18
2.1.1 Obtain IECUBE Configuration data ..........................................................................................18
2.1.2 .....................................................................................................................................................18
2.2 Clock Settings.....................................................................................................................................19
2.3 Mounting and Connecting Connectors ...............................................................................................24
2.3.1 Mounting NQ to target system..................................................................................................24
2.3.2 Mounting YQ to NQ ..................................................................................................................25
2.3.3 Plugging EA into YQ.................................................................................................................26
2.3.4 Precautions for handling NQ, YQ, SA, and CA ........................................................................26
2.3.5 Precautions for mounting IC using NQ and MA .......................................................................27
2.4 Connecting QB-RL78D1A to Target System ......................................................................................28
2.5 Notes on Power Supply and GND Pin Connection.............................................................................30
2.6 Connecting USB Interface Cable and AC Adapter.............................................................................31
2.7 Switching Power On and Off...............................................................................................................31
CHAPTER 3 SETTINGS AT PRODUCT SHIPMENT......................................................................................32
CHAPTER 4 CAUTIONS ...............................................................................................................................33
4.1 Cautions Regarding Differences Between Target Device and Emulator ...........................................33
APPENDIX A CHARACTERISTICS OF TARGET INTERFACE ...................................................................35
APPENDIX B REVISIONHISTORY............................................................................................................38
B.1 Major Revisions in This Edition....................................................................................................38
QB-RL78D1A In-Circuit Emulator Preliminary User’s Manual ZUD-BG-11-0085
7
CHAPTER 1 GENERAL
The QB-RL78D1A is an in-circuit emulator for emulating the RL78/D1A.
Hardware and software can be debugged efficiently in the development of systems in which the RL78/D1A is used.
This manual descries basic setup procedures, hardware specifications, system specifications, and how to set switches.
QB-RL78D1A In-Circuit Emulator Preliminary User’s Manual ZUD-BG-11-0085
8
1.1 Hardware Specifications
Table 1-1. QB-RL78D1A Hardware Specifications
Parameter Specification
Target device RL78/D1A
Operating voltage 2.4～5.5V
High-speed system clock 2.4 V ≦VDD ≦5.5 V：1～20 MHz
Internal high-speed oscillation clock 2.4 V ≦VDD ≦5.5V：1～32 MHz
Low-speed system clock 2.4 V ≦VDD ≦5.5 V：15 kHz
Operating
frequencyNote
Subsystem clock 2.4 V ≦VDD ≦5.5 V：32.768 kHz
Operating temperature range 0 to 40°C (No condensation)
Storage temperature range -15 to 60°C (No condensation)
External dimensions See figure below
Power
consumption
Target system power supply Voltage: 2.4 to 5.5 V
Maximum current consumption : Approx. 0.2mA
Weight Approx. 400 g
Host interface USB interface (1.1, 2.0)
Note Errors are within ±0.5%. However, this does not apply to errors of the oscillator or clock system
on the target board.
Notes 1. Does not include projection of power switch
2. Includes projection of screw that fixes rear space adapter
3. Rear space adapter can adjust the height from 30 mm (longest) to 0 mm (shortest)
4. Front space adapter can adjust the height from 20 mm (longest) to 5 mm (shortest)
<R>
QB-RL78D1A In-Circuit Emulator Preliminary User’s Manual ZUD-BG-11-0085
9
1.2 Names and Functions of Hardware
Figure 2-1. Names of Parts of QB-RL78D1A
Top View Bottom View
Power switch
POWER TARGET
Power supply connector
USB connector
Side View
TCN2TCN1
OSC1
TCN3
CN6
QB-RL78D1A In-Circuit Emulator Preliminary User’s Manual ZUD-BG-11-0085
10
(1) TCN1, TCN2, TCN3
These are connectors for connecting a check pin adapter or emulation probe.
(2) OSC1
This is a socket for mounting the oscillator.
(3) CN4
This is a connector for the shipment inspection. It is not something that the user will need.
(4) POWER (Red LED)
This is an LED that shows whether the power supply of the QB-RL78D1A is switched on.
LED State QB-RL78D1A State
Lit Power switch ON
Not lit Power switch OFF or AC adapter not connected to QB-RL78D1A
Blinking Internal error occurred (Contact an Renesas Electronics sales representative or
distributor)
(5) TARGET (Green LED)
This is an LED that shows whether the power supply of the target system is switched on.
LED State Target System State
Lit Target system power supply ON
Not lit Target system power supply OFF or target system not connected
(6) Power switch
This is the power switch of the QB-RL78D1A.
It is OFF at shipment.
Inhaltsverzeichnis
Andere Renesas Mikrocontroller Handbücher
Renesas
Renesas V850ES/JE3-L Bedienungsanleitung
Renesas
Renesas RL78/G1P Gebrauchsanweisung
Renesas
Renesas RX65N Series Bedienungsanleitung
Renesas
Renesas RX700 Series Bedienungsanleitung
Renesas
Renesas V850ES/JE3-E Bedienungsanleitung
Renesas
Renesas RX65N Series Bedienungsanleitung
Renesas
Renesas RX62T Bedienungsanleitung
Renesas
Renesas RL78/I1C Bedienungsanleitung
Renesas
Renesas RA Series Bedienungsanleitung
Renesas
Renesas Synergy DK-S7G2 Bedienungsanleitung
Renesas
Renesas RL78/G23-128p Bedienungsanleitung
Renesas
Renesas FG4-768K Series Bedienungsanleitung
Renesas
Renesas RX63N Bedienungsanleitung
Renesas
Renesas R20UT2113EJ0100 Bedienungsanleitung
Renesas
Renesas 78K0/FB2-L Bedienungsanleitung
Renesas
Renesas RL78/G23 Bedienungsanleitung
Renesas
Renesas RX100 Series Bedienungsanleitung
Renesas
Renesas RH850 Series Bedienungsanleitung
Renesas
Renesas M16C/64A Series Bedienungsanleitung
Renesas
Renesas RX65N Series Bedienungsanleitung
Beliebte Mikrocontroller Handbücher anderer Marken
AMS
AMS AS7261 Demo Kit Bedienungsanleitung
Novatek
Novatek NT6861 Bedienungsanleitung
Espressif Systems
Espressif Systems ESP8266 SDK Einrichtungshandbuch
Nuvoton
Nuvoton ISD61S00 ChipCorder Leitfaden
STMicrolectronics
STMicrolectronics ST7 Assembler Linker Bedienungsanleitung
Texas Instruments
Texas Instruments Chipcon CC2420DK Bedienungsanleitung
Lantronix
Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung
NEC
NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung
Mikroe
Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung
Intel
Intel Agilex Bedienungsanleitung
Cypress
Cypress CY4607 HX2VL Bedienungsanleitung
DIGITAL-LOGIC
DIGITAL-LOGIC MICROSPACE Bedienungsanleitung
Texas Instruments
Texas Instruments TMS320F2837 D Series Bedienungsanleitung
CYPRES
CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung
Texas Instruments
Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung
Espressif Systems
Espressif Systems ESP8266EX Betriebsanleitung
Abov
Abov AC33M8128L Bedienungsanleitung
Laird
Laird BL654PA Bedienungsanleitung