Renesas RZ/A2M Bedienungsanleitung
Quick Start Renesas Evaluation Board Kit
for RZ/A2M
Display Output
Board
User Switches
User LED
MIPI Camera
Header
Reset Switch
Debugger Header
Power LED
J-Link Lite
Debugger
Power Switch
CPU Board
Socket
CPU Board
Sub Board
MIPI 8MP
Camera Board
USB Power
(Mini USB)
USB Serial
(Micro USB)
NOTE: This Quick Start Guide covers installation of the e2studio IDE (available from https://www.renesas.com/e2studio
where version 7.3.0 or later is required). An active internet connection is requiredfor downloading the installer.
1. Installation
Do not connect the debugger module until the software support has been installed.
Internet access is required during the installation process.
1. Software for this Renesas Evaluation Board Kit is available for download from;
2. After download the installerwill run and displaythe Welcome dialog box. Follow theon-screen instructions to install
the IDE software, selectingthe RZ device family when prompted.This process will take several minutes.
Note:
Windows™10 / 8.1 / 8 / 7 users may see “User Account Control” dialog box. If applicable, enter the administrator
password and click ‘Yes’.
The Windows™driver signing dialog box may be displayed. Please accept the driver to continue.
Users may seea Renesastrust certificatedialog box. If applicable select the checkbox to trustthe certificate.
https://www.renesas.com/rza2mevb
2. Preparing the Evaluation Board Kit
3. Connect the CPUboardto the sub board usingthe 204-pin connector (note the keyslot isto the left of centre).
Orientate at approximately 45° fromhorizontal, inserting the edgeconnector fully into the socketbeforegently
rotatingthe CPUboarddown flat until the clampslock the board in place.
2
1
Sub Board
CN1
Actions for inserting CPU
Board in Sub Board CN1
4. Connect the Display Output Board to the display connector(CN15 LCD) onthe sub board. The centralkey ensures
correctorientation byaligning it with the slotin the socket.
5. Connect the Display Output Board to an external monitor capable of 800x600 resolution using a monitor cable (not
supplied).
6. Connect the camera module to the camera connector (CN2 MIPI) on the CPU board.
Open the connector bypulling up on the tagsat either side, then insert the camera’s ribbon cable. The correct
orientation is with the contacts on the ribbon cable facing the CPU, and the blue insulated rectangle to the outside.
To hold the cable firmly, push down on the top of the connectoruntilit clips inplace.
Pull tags to open
Push centre to close
7. Connect the J-Link LITE Segger debugger module to the debugger connector (CN5 Coresight 20) on the CPU
board usingthe ribbon cable.Ensure that pin 1 (red strand) mates with the triangle mark ► on the PCB silk screen.
8. Connect the debuggermodule to a USB port on the host PC. The green LED on the debuggerwillilluminate.
9. The debugger driverswillnow be installed. Note that,this may take up toa minute and administrator privileges will
be required.
Windows™ 7
Windows™ 8.1 / 8
Windows™ 10
“Device driver software installed
successfully” pop-up will appear in
the Windows™ Taskbar and
installation will complete.
An icon will appear in the Windows™
Taskbar and installation will
complete.
A Windows™ taskbar buttons of
“Device Setup” willappear in the
Windows™ Taskbar and installation
will complete.
10. Connect a USB cable between the micro USB Serial connector (CN5 UART) on the sub board and a USB porton
the hostPC. The board willenumerate inthe Device Manager underPorts (COM &LPT) Communications Port
(COMn) as “RZA USB Serial Port”. The micro USB Serial connector (CN5 UART) on the sub board may be used to
providea serialconsole forthe sample applications.
If you have not previously installed another Renesas kit with this virtual serial port driver, or if the boardenumerates
as an “Unknown device,”then disconnect the board and install the “RZ/A2M Evaluation Board Kit inf File for USB to
Serial Conversion IC” available from https://www.renesas.com/software/D6002724.html
a. Note: Windows™10 / 8.1 /8 / 7 usersmay see “User Account Control”dialog box. If applicable, enter
the administrator password and click ‘Yes’.
b. The Windows™driver signing dialog box may be displayed. Please accept the driver to continue.
11. Use any serial terminal (e.g.HyperTerminal, Tera Term orPuTTY), select the appropriate COMport and set the
baud-rate to 115200 bps,Databits to8, Stop bitsto 1,Parity to Noneand FlowasNone.
12. Connect a USB cable between the mini USB Power connector (CN13 USB-F) on the sub boardand a USB port on
the host PC.
13. Apply power by moving SW1 away from the power jack; the blue power LED will illuminate.
14. Power down the systemby moving SW1towards the power jack.
3. Preparing the e2studio development environment
Renesas e2 studio integrates various tools such as compiler, assembler, debugger and editor into a common graphical
user interface.
15. Start e2 studio:
Windows™ 7: Start Menu >All Programs > RenesasElectronics e2studio >e2 studio
Windows™ 8.1 & 8: From Apps View , RenesasElectronics e2studio > e2 studio
Windows™ 10: Start Menu > All Apps > Renesas Electronics e2studio > e2 studio
16. In the ‘Select aworkspace’folderthat appears,browse a suitable locationand foldername to save yournew
workspace to. Click ‘OK’ to continue.
17. In the ‘Toolchain Registry’dialog box select Renesas Toolchains and ensure that ‘GCC ARM Embedded
6.3.1.20170620’ is selected. Click ‘Register’. A dialog box will appear "Selected Toolchains were successfully
integrated with e2 studio". Click ‘OK’.
18. If the ‘Code GeneratorRegistration’dialog box is shown, click ‘OK’ and follow the on-screen instructions to restart
e2studio. Thisis requiredbefore the Code Generatorcan be used.
19. To learn more onhow touse e2 studio, openthe program’s help filesby using Help> Help Contents.
4. Next Step
20. In the e2 studio Welcome screen, click the ‘Workbench’ arrow icon, on the farright.
You are ready to download and program an application from the RZ/A2M Simple Applications Package
(R01AN4494EJ).
21. Select one of the available application notes, and follow the instructions in the readme files,ensuring the correct
switch and jumpersettingsare made before applying power. Recommendations:
● If you have a display supporting 800x600 input,accessthe camera_display_sample (R01AN4477EJ).
● If you want to quickly check the kit’s operation, access the blinky_osfree_sample (R01AN4321EJ).
5. GNU ARM Compiler
The version of the compilerprovided with this evaluation board kit is fully functional.
6. User Manuals
The user manuals for this product are available at: https://www.renesas.com/rza2mevb
This includes, but not limited to:
● RZ/A2 Group User’s Manual: Hardware (R01UH0746EJ)
● CPU Board User’s Manual (R20UT4397EJ)
● Sub Board User’sManual(R20UT4398EJ)
7. Support
Online technical support and information is availableat: https://www.renesas.com/rza2mevb
Technical Contact Details
America: techsupport.america@renesas.com
Europe: https://www.renesas.com/eu/en/support/contact.html
Global & Japan: https://www.renesas.com/support/contact.html
© 2018-2019 Renesas Electronics Europe Limited. All rights reserved.
© 2018-2019 Renesas Electronics Corporation. All rights reserved.
Website: https://www.renesas.com/
D016404_11_S01_V02
R20UT4399EJ0200, 28-JAN-2019
Andere Renesas Hauptplatine Handbücher
Renesas
Renesas ZSSC324 Series Bedienungsanleitung
Renesas
Renesas Y-G-HYBRID-PLC-RF Bedienungsanleitung
Renesas
Renesas RTD120D-EVK Bedienungsanleitung
Renesas
Renesas RAA226110 Bedienungsanleitung
Renesas
Renesas 8V9705 Series Bedienungsanleitung
Renesas
Renesas RL78/G1N Bedienungsanleitung
Renesas
Renesas RTKA214250DE0020BU Bedienungsanleitung
Renesas
Renesas RL78/G1D Bedienungsanleitung
Renesas
Renesas US082-FS1015EVZ Bedienungsanleitung
Renesas
Renesas R0K572167 Bedienungsanleitung
Renesas
Renesas RA6 Series Bedienungsanleitung
Renesas
Renesas RSSKRX23E-B Bedienungsanleitung
Renesas
Renesas ISL91134IIQ-EVZ Bedienungsanleitung
Renesas
Renesas ISL6263AEVAL1Z Bedienungsanleitung
Renesas
Renesas US082-FS2012EVZ Bedienungsanleitung
Renesas
Renesas RTKA211651DE0000BU Bedienungsanleitung
Renesas
Renesas RA4 Series Bedienungsanleitung
Renesas
Renesas RTKA788152DE0000BU Bedienungsanleitung
Renesas
Renesas RTKA223181DE0010BU Bedienungsanleitung
Renesas
Renesas RA2A1 Series Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
