Renkforce FDM 3D Printer Pro 6+ Bedienungsanleitung

Insert the print bed and magnetic mat.

Remove the styrofoam pads

1. Install the spool holder.

2. Slide the lament spool onto the holder.

1. Insert the lament tube in the feeder.

2. Insert the lament tube into the extruder.

System

Tool Print

1. Connect the mains cable to the power inlet on the printer.

2. Flip the power switch into the position I to switch on. The display lights up.

Quick Start Guide

FDM 3D Printer Pro 6+

Item No. 2583518

Read the safety instructions supplied

with the product before using

1Set printer up 2Calibrate Z-Offset

Insert the print bed and magnetic mat.

Open the menu Tools.Touch the button Preheating to start the pre-

heating process.

Wait until the preheat temperature has been reached.

Open the menu Manual.Touch to move the extruder to its zero posi-

tion.

Activate the Z-offset calibration with the slider. Touch the distance increment 0.1 mm to

activate it.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights including translation reserved.

Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data processing systems require the prior written approval

by the editor. Reprinting, also in part, is prohibited. This publication represents the technical status at the time of printing.

3Load lament

Open the menu Tools.Open the menu Filament.

Touch the temperature display to preheat the

extruder.

Cut the lament at an angle and then feed it into

the feeder.

Touch the button E1 Load to load the lament

into the extruder.

Touch the button Stop as soon as molten lament ows from the nozzle.

4Print

CAUTION

Hot print bed

Touching hot print bed can cause burns

Let cool down before touching

System

Tool Print

Connect the USB memory stick that contains

the print le to the USB port.

Open the menu Print.

Body-Mido.gcode

mm/s

16%

191/190

51/50 100mm/s

04h07m 03h06m

K1-07-11.gcode

Select le to print. The printer starts printing.

5 6

After printing is complete, let the printer cool

down to room temperature.

Remove the magnetic mat.

Slide one sheet of A4 paper (80 g) between the

nozzle and the print bed.

Slide the paper back and forth while repeatedly touching the button or to lift or lower the

print bed. If you notice slight resistance between nozzle, paper, and print bed, touch the button

to nish the calibration.

Conrm the Z-offset calibration. Touch the button Leveling to start

“Auto-levelling”.

Wait for “Auto-levelling” to nish.

Andere Handbücher für FDM 3D Printer Pro 6+

Dieses Handbuch passt für folgende Modelle

Andere Renkforce 3D-Drucker Handbücher

Renkforce

Renkforce RF1000 Bedienungsanleitung

Renkforce

Renkforce RF100 XL Betriebsanleitung

Renkforce

Renkforce 3D Drucker Cube One Bedienungsanleitung

Renkforce

Renkforce RF2000 v2 Series Bedienungsanleitung

Renkforce

Renkforce 2583518 Betriebsanleitung

Renkforce

Renkforce RF500 Maker Construction Kit Bedienungsanleitung

Renkforce

Renkforce 1522157 Leitfaden

Renkforce

Renkforce FDM 3D Printer Pro 6+ Bedienungsanleitung

Renkforce

Renkforce RF100 v2 Bedienungsanleitung

Renkforce

Renkforce 2584537 Firmware-Update

Renkforce

Renkforce 1528625 Bedienungsanleitung

Renkforce

Renkforce RF2000 Bedienungsanleitung

Renkforce

Renkforce Pro 6 Bedienungsanleitung

Renkforce

Renkforce RF Pro 3 Bedienungsanleitung

Renkforce

Renkforce 1538778 Leitfaden

Renkforce

Renkforce RF100 XL Bedienungsanleitung

Renkforce

Renkforce RF100 Bedienungsanleitung

Renkforce

Renkforce Basic 3 Bedienungsanleitung

Renkforce

Renkforce RF100 Konfigurationshandbuch

Renkforce

Renkforce RF100 Bedienungsanleitung

Renkforce

Renkforce FDM 3D Printer Pro 6+ Bedienungsanleitung

Renkforce

Renkforce 1521716 Leitfaden

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch