Replay XD720 Bedienungsanleitung
QUICK START GUIDE
Replay XD720 Camera
(A) Power On/O,
(B) Record, Stop, Clip,
(C) Removable Lens Cover
(D) Removable End Cap
(E) Record On/O Red LED
(F) Power On/O Blue LED
(G) Horizontal Sight Line
(H) Vertical Sight Line
(I) microSDHC Slot
(J) Charging Green LED, No SD Card Red LED
(K) Frame Rate Switch (FPS)
(L) Audio Line-In Switch (Ext. Mic-In)
(M) Mini USB 8-Pin Port
(*) Master Reset ORIENTATION
C
G
H
D
L
M
I
J
K
*
E F
A B
RECORDING
Press A to Power On/Power O. Press B to START/STOP Recording. Your Done.
Power On (Standby & Mode Setting Selection): Hold down front button (A) for 2 sec. & release, the Replay
XD720 will vibrate 3 times & illuminate the blue power LED.
Note: Camera will turn o after 5 seconds if no SD card is present. Camera will turn o after 5 minutes of no activity.
Start Recording: Hold down rear button (B) for 2 sec. & release, the Replay XD720 will vibrate 3 times, illuminate
the red LED & automatically start recording or capturing.
Note:The red LED on the rear will blink when the memory card is not inserted properly. Make sure the memory card
is fully inserted with the gold contacts face-down until it clicks. Use only Replay XD approved SD cards.
Visit www.replayxd.com for SD card compatibility list.
Stop Recording: Hold down the rear button (B) for 4 sec. & release, the Replay XD720 will vibrate 1 time to notify
you that it is saving the le.
Power O: Hold down the front button (A) for 4 sec. and release, the Replay XD720 will vibrate 1 time & power o.
Note:The power button will not function when recording. This is normal to prevent accidental powering o.
Clip File: While recording quickly press the rear button (B) and release, the Replay XD720 will vibrate 1 time to notify you that
it is clipping & saving the le, then automatically starts recording.This feature allow you to start a new le without starting or
stopping the recording.
E F
A B
MODES & SETTINGS
720p Video Mode / Frames Per Second
1. Slide the FPS switch (K) to change frames per second.
a. 30 FPS (Broadcast HD)
b. 60 FPS (Smooth HD)
Audio Option
1. Slide the INT./EXT. switch (L) to choose audio option.
a. Internal Mic (Default)
b. External Mic-in, disables internal Mic
External Mic-in is compatible with Replay XD720 HDMI Audio Adapter or
Replay XD720 HW Kit, available at www.replayxd.com
For Advanced Users and Setting Proles visit www.replayxd.com/replay-XD720-advanced/
REAR VIEW
L
K
1. Find the best mounting location for your Replay XD720 and check your angles.
Rigid surfaces are ideal for the best video quality. Note: You can make a test recording and check
it on an iPad/Mac/PC.
2. Snap Replay XD720 into u-shape camera holder and rotate 360º to desired rotation.
3. AttachVHB SnapTray adhesive mount to a clean smooth surface.
-Flat SnapTray’s are good for at smooth surfaces.
-Curved SnapTray’s are good for curved surfaces such as Helmets & Radius surfaces.
The 3MVHB adhesive is not recommended for textured surfaces.
4. Slide HeimLock mount into SnapTray until it is fully seated and clicks.
5. Adjust swivel 360º or tilt ~8º by releasing the heim cam lever and position Replay
XD720 in desired direction, then lock the cam lever. Make sure the cam lever is tight.
There is an adjustable tension wheel and phillips screw (*) to make sure you always have
a positive tight lock. You can tighten the screw clockwise in 1/4 turn increments to nd
the desired tension when the cam lever is locked.
HEIMLOCK MOUNT
See our full range of mounts at www.Replayxd.com
*
VHB SnapTray HeimLock Mount
Unlock
Lock
Tighten
Set screw
TiltSwivel
IMPORTANT
Use rubbing alcohol to clean
the mounting surface. Wipe
dry the surface. Apply your
VHB mount to surface. Press
and hold for sixty seconds to
allow adhesive to bond to
the surface. Bond strength
will increase through time.
At room temperature,
wait for at least 24 hours
to achieve 90% bonding
strength, and 72 hours for
100% bonding strength.
1. Find the best mounting location for your Replay XD720 and check your angles.
Rigid surfaces are ideal for the best video quality. Note: You can make a test recording and
check it on an iPad/Mac/PC.
2. Flip LowBoy mount upside down and carefully spread, insert Replay XD720 into
holder with buttons passing through the cut-out.
3. With the Replay XD720 centered in LowBoy mount, rotate 360º to desired rotation.
4. Slide LowBoy mount into SnapTray until it is fully seated and clicks. The LowBoy mount has
rubber strips to hold your Replay XD720 from rotating when seated, make sure your rotation
angle is ideal.You can make ne adjustments by sliding the LowBoy in/out of the SnapTray.
5. Attach VHB SnapTray adhesive mount to a clean smooth surface.
The 3M VHB adhesive is not recommended for textured surfaces.
LOWBOY MOUNT
See our full range of mounts at www.Replayxd.com
VHB SnapTray LowBoy Mount
Unlock
Lock
IMPORTANT
Use rubbing alcohol to clean
the mounting surface. Wipe
dry the surface. Apply your
VHB mount to surface. Press
and hold for sixty seconds to
allow adhesive to bond to
the surface. Bond strength
will increase through time.
At room temperature,
wait for at least 24 hours
to achieve 90% bonding
strength, and 72 hours for
100% bonding strength.
ALIGNMENT
There are a few references for accurately aiming and aligning your Replay XD720.
1. The Start REC button should always point up or at the 12 o’clock position for a level horizon.
2. The silver sight markers are at 3 o’clock & 9 o’clock and can act as a horizontal level.
3. The red sight markers are at 12 o’clock & 6 o’clock and can act as a vertical level.
4. The laser etched logos on the side of the Replay XD720 are level and can act as tilt indicators.
5. To make sure you are aiming your Replay XD720 in the desired direction, simply look down the length of the
housing from the rear–forward as if you’re looking through a telescope. It’s that easy.
12
9
6
3
RIDING HEAD POSITION
ACTUAL LINE OF SIGHT
ACTUAL LINE OF SIGHT (HORIZON LINE)
MOUNTING
HEIMLOCK SWIVEL/TILT MOUNT
LOWBOY MOUNT
Mounting angle and setup:
1. When using a HeimLock mount or LowBoy mount it is important to mount them at an optimal position.
Please reference the illustration on this page for possible positions.
2. When mounting to a helmet, most people have a tendency to lower their head from 15º to and excess of 20º.
It is important to recognize what the natural angle or active position of your mounting locations are on items
such as: helmets, hats, handlebars, vehicle bodies, etc.This will help you to achieve the best angle and capture
professional looking video.
3. For best results have a friend look at your active riding & head position to choose your optimal camera angle
based on your riding position before applying your VHB SnapTray.
Note: You can make a test recording and check it on an iPad/Mac/PC.
See our full range of mounts and mounting ideas at www.Replayxd.com
1. Remove rear protective cap and connect the supplied mini USB
cable into the Replay XD720 USB port.
2. Plug the USB cable into the supplied Car Adapter, PC/Mac USB 2.0
port, or our AC Wall Adapter accessory.
3. The green charging status LED at the rear of the Replay XD720 will
illuminate to tell you it’s charging. When the green LED turns o,
the battery is full and charging is complete
Note: Charging through the PC/Mac USB port will take approximately
twice as long as using the AC Wall Adapter or Car Adapter. It is not
recommended to record while charging through the PC/Mac USB port
as the Replay XD720 uses approximately the same power draw as
the PC/Mac USB port, damage to the Replay XD720 or your computer
may occur.
The Replay XD720 will record for approx. 130 min. on a full charge
in optimal conditions. Extreme heat or cold can aect battery life.
SIDE VIEW REAR VIEW
PC/MAC
CHARGING
PC/MAC
MINI USB 2.0
CHARGE/SYNC
CABLE
DOWNLOAD
1. Remove rear protective cap and use option (1) or option (2).
2. Option (1):Take the microSDHC out of the Replay XD720 and use a
SDHC compatible card reader to transfer your les to your computer.
3. Option (2): Download from the Replay XD720 USB port.
4. Plug USB cable into Replay XD720 and a PC/Mac USB 2.0 port.
5. Press and hold the Start/Stop (B) and Power On your Replay XD720.
6. On a PC/Mac your Replay XD720 will mount to your computer
as a mass storage device.You may download your video les
from the DCIM folder created on the microSDHC card.
(Always Eject device from PC/Mac)
Note: Option (2) may exhibit slow transfer speeds.
Playback through USB is not recommended as choppy
playback may occur. Download footage to PC/Mac rst.
PC/MACPC/MAC
MINI USB 2.0
CHARGE/SYNC
CABLE
SIDE VIEW
HOW TO ERASE FILES
1. Move selected video files or folders to yourTrash Can
or Recycle Bin
2. For Mac: Go to Finder and select Empty Trash...
Note:SimplymovingfilesorfolderstotheTrashdoesnot
erase files from your memory card, it just moves them
(referenced in the Trash). Files are invisibly stored on
your memory card until theTrash is emptied.
REAR VIEW
B
Inhaltsverzeichnis
