Replus Replus-250 Bedienungsanleitung

User Manual

Replus-250 Replus-250A Replus-250B

Australia

Add: 18 Corporate Blvd. Bayswater, VIC 3153, Australia

T: +61 481 251 275

APMEA & China

Add: F-15,Manpo Intl. No.500 WestYan’an Rd, Shanghai, China 200050

T: +86 21 62809180

Web: www.renesola.com

E: [email protected]

U.S.A

Add: 301 Howard St, Suite 850, San Francisco, CA 94105.

T: +1 415 852 7418

Europe

Add: Renesola Deutschland GmbH, Lyoner Strasse 15, 60529 Frankfurt/M, Germany

T: +49 69 663 786 9-0

CONTENT

COMPANY PROFILE 01

1. INTRODUCTION 01

Preﬁx 01

1.1 Grid-ed PV System 01

1.2 How to Use This Manual 01

2. SAFETY INSTRUCTIONS 02

3. FCC COMPLIANCE 02

4. INSTALLATION 03

5. COMMISSIONING 07

6. OPERATING INSTRUCTIONS 07

7. TROUBLESHOOTING AND MAINTENANCE 08

8. SPECIFICATIONS 10

9. WARRANTY 11

10. CONTACT US 13

11. APPENDIX 14

11.1 Warranty Card 14

11.2 Examples of connecon diagram 15

11.3 Connecon Map 17

COMPANY PROFILE

ReneSola has been listed on New York Stock Exchange (NYSE:SOL) in 2008. Its products have been

delivered around the world since its establishment. It has mulple locaons worldwide, with

sales and operaons facilies in the United States, Europe, and Asia-Paciﬁc regions. ReneSola has

a strong focus on helping customers meet delivery schedules, using high quality photovoltaic

modules and PV micro grid-ed inverter.

1. INTRODUCTION

Preﬁx

Thank you for selecng the ReneSola Micro Replus-250/ Replus-250A/B inverter. We are certain

our products will meet your project and business needs. We appreciate your feedback regarding

our products, and invite you to contact us at inverter@renesola.com or www.renesola.com for

more informaon.

1.1 Grid-ed PV System

Grid-ed PV systems consist of PV panels, grid-ed inverters, juncon boxes, etc. The power

generated by the micro inverter is converted from DC to AC energy and feedback to the grid,

through net metering, using the Micro Replus-250/ Replus-250A/B .

1.2 How to Use This Manual

This manual provides detailed product informaon and installaon instrucons for the

Replus-250/ Replus-250A/B micro-inverter. Please read this manual prior to installaon and

operaon.

02 03

3. FCC COMPLIANCE

2. SAFETY INSTRUCTIONS

Warning: Please Read This Manual Before Installaon. Any Damage To The Product Due To

Not Following This Manual Is Not Covered By The Warrantee. All The Installaon Should Be

Done By A Cerﬁed Electrician. Besides The Cable Connectors, Nothing Else On Or In

Microinverter Should Be Modiﬁed.

All Installaons Should Follow The Local Electriccodes. The Replus-250/ Replus-250A/B Does Not

Include Components That Can Be Served By Customers. Opening Or Aempng To Modify Or

Change The Construcon Or Design Of The Microinverter Shall Void The Warranty. Please Contact

Authorized Service Agents For Any Service Work.

Replus-250/ Replus-250A/B Is A Grid-ed Solar Inverter. It May Require Approval From Local

Ulity Company Prior To Grid Inter Connecon.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon

against harmful interference in a residenal installaon. This equipment can radiate energy from

radio frequencies and, if not installed and used in accordance with the instrucons, may cause

harmful interference with radio communicaons. If this equipment does cause harmful

interference to radio or television recepon, which can be determined by turning the equipment

oﬀ and on, the user is encouraged to aempt to correct interference by taking one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separaon distance between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit diﬀerent from that to which the receiver is

connected.

•Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcaons not expressly approved by the party responsible for compliance may

void the user’s authority to operate the equipment.

4. INSTALLATION

Warning: Be Aware That Installaon Of This Equipment Includes Risk Of Electric Shock.

Normally, Grounded Conductors Maybe Ungrounded And Energized When A Ground Fault

Is Indicated.

Parts Included

In addion to the Replus-250/ Replus-250A/B micro inverters, PV modules, rack, and associated

hardware, you’ll need the Replus-250/ Replus-250A/B installaon kit. This kit includes the

following items:

• Installaon ﬁxed screws

• Grounding ﬁxed washers

• User manual

• Warranty Terms and Warranty Card

Other Required Parts And Tools

In addion to your PV array and its associated hardware, you will need to provide the following:

• Juncon box

• Connuous grounding wire

• Number 2 Phillips screwdriver

• Sockets and wrenches for mounng hardware

• Torque wrench

• Mounng hardware suitable for module rack

Lightning Surge Suppression

Lightning does not actually need to strike the equipment or building where a PV system is

installed to cause damage. Oen, a strike nearby will induce surges in the electrical grid that can

potenally exceed maximum voltages and damage equipment. The Replus-250/ Replus-250A/B

has integral surge protecon, greater than most string inverters. However, if the surge has

suﬃcient energy, the protecon built into the Replus-250/ Replus-250A/B can be exceeded, and

the equipment can be damaged.

The ReneSola Limited Warranty does not cover “acts of God” such as lightning strikes, and since

lightning strikes can occur any where, it is recommended to install surge protecon as part of any

solar installaon. Installaon of surge protecon devices should follow vendor instrucons.

04 05

Step 2 - Connect the Replus-250/ Replus-250A/B Cable

Each Replus-250/ Replus-250A/B comes with one 3-pin bulkhead receptacle (or short pigtail) and

one 57-inch AC wire harness with mul-pin connectors. (The DC input wires are approximately six

inches long and are terminated with single pole connectors.) The AC connectors are oppositely

sexed, so that mulple inverters can be connected to form one connuous AC branch circuit.

1. Orient the ﬁrst Replus-250/ Replus-250A/B in each branch with its male connector facing the

juncon box. The juncon box AC interconnect cable has a female connector. The Replus-250/

Replus-250A/B can be mounted with either side facing up to accommodate cable roung.

Connect the ﬁrst Replus-250/ Replus-250A/B to the AC interconnect cable.

2. Plug the AC connector of the ﬁrst Replus-250/ Replus-250A/B into the connector of the next

Replus-250/ Replus-250A/B, and so forth, to form a connuous AC circuit. Please check the

Replus-250/ Replus-250A/B rang label for the maximum allowable number of Replus-250/

Replus-250A/B’s on one AC circuit.

Warning: Do Not Exceed The Maximum Number Of Replus-250/ Replus-250a/b’s In An Ac

Branch Circuit, As Displayed On The Unit-rang Label. Each Replus-250/ Replus-250a/b Ac

Branch Circuit Must Be Sourced From A Dedicated Branch Circuit Protected By A 15a

Maximum Breaker.

3. Install a protecve end cap on the open AC connector of the last Replus-250/ Replus-250A/B in

the AC branch circuit.

Warning: Make Sure Protecve End Caps Have Been Installed On All Unused Ac Connectors.

Unused Ac Replus-250/ Replus-250A/B Wire Harness Connectors Are Live When The System

Is Energized By The Ulity System.

Step 3 - Install the AC Branch Circuit Juncon Box

1. Measure service entrance conductors to conﬁrm AC service at the site. Acceptable ranges are

shown in the table below:

2.Mount the adapter plate at a suitable locaon on the PV rack system (typically at the end of a

row of modules).

3.Install an appropriate juncon box with the adapter plate.

4.Connect the open wire end of the AC interconnect cable into the juncon box using an

appropriate cable.

1. Mark the approximate centers of each PV module on the rack system. Evaluate the locaon of

the micro inverter with respect to the PV module juncon box or any other obstrucons.

Warning: Allow A Minimum Of 0.75 Inches Between The Top Of The Roof And The Boom Of

The Replus-250/ Replus-250a/b. We Also Recommend That You Allow 0.5 Inches Between The

Back Of The Pv Module And The Top Of Replus-250/ Replus-250a/b. Do Not Mount Replus-250/

Replus-250a/b In A Locaon That Allows Long-term Exposure To Direct Sunlight.

2. If using grounding washers to ground the micro inverter chassis to the PV module rack, choose

a grounding washer that is approved for the rack manufacturer. Install a minimum of one

grounding washer per micro inverter. Tear down barcode from inverter, paste the barcode into

the “Connecon map”. Torque the micro inverter fasteners to the values listed below.

1/4” mounng hardware – 45 in-lbs minimum

5/16” mounng hardware – 80 in-lbs minimum

Warning: Do Not Connect Replus-250/ Replus-250A/B To The Ulity Grid Or Energize The Ac

Circuit(S) Unl You Have Completed All Of The Installaon Procedures As Described In The

Following Secons.

Installing the Replus-250/ Replus-250A/B micro inverter System involves several key steps:

1. Aaching the Replus-250/ Replus-250A/B micro inverter to the rack.

2. Connecng the Replus-250/ Replus-250A/B micro inverter wiring harnesses.

3. Measuring service and installing the AC branch circuit juncon box.

Warning: Only Use Electrical System Components Approved For Wet Locaons.

4. Grounding the system.

5. Compleng the Replus-250/ Replus-250A/B micro inverter installaon and connecng the PV

modules.

The ﬁnished system should be similar as in the diagram. Detailed installaon steps are listed in the

following secon.

Installaon Procedure

Step 1 - Aach the Replus-250/ Replus-250A/B to the Rack

3. Mount one micro inverter at each of these locaons using hardware

recommended by your module rack vendor. Mounng slots on the micro

inverter are 0.33 inches in diameter. Maximum bolt size is 5/16 inch.

The two slots on the micro inverter are 4 inches apart

240 Volt AC Split Phases 208 Volt AC Three Phases 230 Volt AC Single Phase

L1 to L2 211 to 264 Vac L1 to L2 183 to 229 Vac

L1 to L2 200 to 270 Vac

L1, L2 to neutral 106 to 132 Vac L1, L2 to neutral 106 to 132 Vac

Step 4 – Ground the System

Each Replus-250/ Replus-250A/B comes with a ground clip that can accommodate a 6-8 AWG

conductor. The rack and module could be grounded to this conductor using a crimp connecon.

An alternave method would be to connect the Replus-250/ Replus-250A/B to the grounded rack

using a grounding washer approved for the rack.

Completely install all Replus-250/ Replus-250A/B and system inter-wiring connecons prior to

installing the PV modules.

1. Mount the PV modules above the corresponding Replus-250/ Replus-250A/B. Each

Replus-250/Replus-250A/B comes with two oppositely sexed DC connectors.

2. First connect the posive DC wire from the PV module to the negavely marked DC connector

(male pin) of the Replus-250/ Replus-250A/B. Then connect the negave DC wire from the PV

module to the posively marked DC connector (female socket) of the Replus-250/

Replus-250A/B. Repeat for all remaining PV modules using one Replus-250/ Replus-250A/B for

each module.

Step 5 - Connect the PV Modules and Complete the connecon map

Connect the PV Modules

The Replus-250/ Replus-250A/B Connecon Map is a diagrammac representaon of the

physical locaon of each Replus-250/ Replus-250A/B in your PV installaon. The virtual array in

the ReneSola micro inverter gateway, MRG, is created from the map you create.

Each Replus-250/ Replus-250A/B has a serial number, enter this serial number into the MRG

according with barcode of “connecon map”, so MRG can correspond with micro inverter and

internet.

Complete Connecon Map

Warning: Connectreplus-250/ Replus-250a/b To The Electrical Ulity Grid Only Aer

Receiving Prior Approval From The Ulity Company.

Warning: Be Aware That Only Qualiﬁed Personnel Must Connect Replus-250/

Replus-250a/b To The Electrical Ulity Grid.

Warning: Ensure That All Ac And Dc Wiring Is Correct. Ensure That None Of The Ac And Dc

Wires Are Pinched Or Damaged. Ensure That All Juncon Boxes Are Properly Capped And Not

Exposed.

Following these steps to commission the Replus-250/ Replus-250A/B PV system:

1. Turn ON the AC disconnector or circuit breaker on each Replus-250/ Replus-250A/B AC branch

circuit.

2. Turn ON the main ulity-grid AC circuit breaker. Your system will start producing power aer a

few minutes wait me.

3. The Replus-250/ Replus-250A/B will start to send performance data over the power lines using

power line communicaon (PLC) to the MRG. The me required for each Replus-250/

Replus-250A/B in the system to communicate to the MRG will vary with the number of

Replus-250/ Replus-250A/B’s in the system.

Status: standby

5. COMMISSIONING

6. OPERATING INSTRUCTIONS

The Replus-250/ Replus-250A/B is powered on when suﬃcient DC voltage from the module is

applied. The status LED will start ﬂashing aer suﬃcient DC power is applied as an indicaon that

the Replus-250/ Replus-250A/B is live.

The LED light is on by 2 seconds, and oﬀ by 2 seconds.

Status: producing power

The LED light is on by 1 second, and oﬀ by 1 second.

Status: producing power and communicang with MRG

The LED light is on by 0.5 second, and oﬀ by 0.5 second.

06 07

Installing a replacement Replus-250/ Replus-250A/B

Disconnecng a Replus-250/ Replus-250A/B from the PV Module

1. Aach the replacement Replus-250/ Replus-250A/B to the PV module rack using hardware

recommended by your module rack vendor. If you are using grounding washers (e.g., WEEB) to

ground the chassis of the Replus-250/ Replus-250A/B, the old grounding washer should be

discarded and a new grounding washer must be used when installing the replacement

Replus-250/ Replus-250A/B. Torque the Replus-250/ Replus-250A/B fasteners to the values

listed below:

1/4” mounng hardware – 45 in-lbs minimum.

5/16” mounng hardware – 80 in-lbs minimum.

2. If you are using a grounding electrode conductor to ground the Replus-250/ Replus-250A/B

chassis, aach the grounding electrode conductor to the Replus-250/ Replus-250A/B ground

clamp.

3. Connect the AC cable of the replacementReplus-250/ Replus-250A/B and the neighboring

Replus-250/ Replus-250A/B to complete the branch circuit connecons.

4. Complete the connecon map and connect the PV Modules

1) Complete the connecon map.

2) Each Replus-250/ Replus-250A/B has a removable serial number label located on the

mounng plate. Enter this serial number into the MRG, and correspond it to a number in the

connecon map.

3) Connect the PV Modules.

4) Completely install all Replus-250/ Replus-250A/B and all system inter-wiring connecons

prior to installing the PV modules.

a) Mount the PV modules above their corresponding Replus-250/ Replus-250A/B. Each

Replus-250/ Replus-250A/B comes with one male and one female DC connector.

b) First connect the posive DC wire from the PV module to the negavely marked DC

connector (male pin) of the R Replus-250/ Replus-250A/B. Then connect the negave DC

wire from the PV module to the posively marked DC connector (female socket) of the

Replus-250/ Replus-250A/B.

Repeat for all remaining PV modules using one Replus-250/ Replus-250A/B for each module.

To ensure the Replus-250/ Replus-250A/B is not disconnected from the PV modules under load,

adhere to the following disconnecon steps in the order shown:

1. Disconnect the AC by opening the branch circuit breaker.

2. Disconnect the ﬁrst AC connector in the branch circuit.

3. Cover the module with an opaque cover.

4. Using a DC current probe, verify there is no current ﬂowing in the DC wires between the PV

module and the Replus-250/ Replus-250A/B.

5. Care should be taken when measuring DC currents, as most clamp-on meters must be zeroed

ﬁrst and tend to dri with me.

6. Disconnect the PV module DC wire connectors from the Replus-250/ Replus-250A/B.

7. Remove the Replus-250/ Replus-250A/B from the PV array rack.

Warning: Do Not Aempt To Repair The Replus-250/ Replus-250a/b; It Contains No

User-service Able Parts. If Troubleshoong Methods Fail, Please Return The Replus-250/

Replus-250a/b To Your Distributor For Maintenance.

Warning: Never Disconnect The Dc Wire Connectors Under Load. Ensure That No Current Is

Flowing Inthe Dc Wires Prior To Disconnecng. An Opaque Covering Maybe Used To Cover

The Module Prior To Disconnecng The Module.

Warning: Always Disconnect Ac Power Before Disconnecng The Pv Module Wires From

Replus-250/ Replus-250a/b. The Ac Connector Of The First Replus-250/ Replus-250a/b In A

Branch Circuis Suitable As A Disconnecng Means Once The Ac Branch Circuit Breaker In

The Load Center Has Been Opened.

Warning: Replus-250/ Replus-250a/b Is Powered By Dc Power From The Pv Modules. Make

Sure You Disconnect The Dc Connecons And Reconnect Dc Power To Watch For The Six

Short Led Blinks One Minute Aer Dc Is Applied.

LED indicaon of error

• Error report: AC or DC fault

The LED light is on by 4 seconds, and oﬀ by 4 seconds.

• Error report: GFDI fault

The LED light stays on.

Troubleshoong an Inoperable Replus-250/ Replus-250A/B

7. TROUBLESHOOTING AND MAINTENANCE

To troubleshoot an inoperable Replus-250/ Replus-250A/B, follow the steps in the order shown:

1. Check the connecon to the ulity grid. Verify that the ulity voltage and frequency are within

allowable ranges shown in the label of the Replus-250/ Replus-250A/B.

2. Verify ulity power is present at the inverter in queson by removing AC, then DC power.

Never disconnect the DC wires while the Replus-250/ Replus-250A/B is producing power.

Re-connect the DC module connectors, and then watch for the LED blinks.

3. Check the AC branch circuit interconnecon harness between all the Replus-250/

Replus-250A/B’s. Verify that each inverter is energized by the ulity grid as described in the

previous step.

4. Make sure that any AC disconnects are funconing properly and are closed.

5. Verify the PV module DC voltage is within the allowable range shown in the label of the

Replus-250/ Replus-250A/B.

6. Check the DC connecons between the Replus-250/ Replus-250A/B and the PV module.

7. If the problem persists, please contact ReneSola customer support.

Warning: Do Not Aempt To Repair The Replus-250/ Replus-250A/B; It Contains No

User-serviceable Parts. If Troubleshoong Methods Fail, Pleasere Turn The Defecve

Replus-250/ Replus-250A/B To Your Distributor For Maintenance.

08 09

Terms of the Product Warranty:

This warranty is provided in an eﬀort to improve service and peace-of-mind to end users of

ReneSola microinverters. All ReneSola authorized Dealers and Distributors are required to

complete a ReneSola Warranty Card in the event of a claim, at which point ReneSola will either

(a) replace or repair any products or parts of the product during the Warranty Period or (b) the

original cost of the Micro Replus inverter, proven defecve in design or manufacturing, will be

refunded. ReneSola will not be obligated to fulﬁll on a warranty claim, if all or any of the

following is true:

1) “Warranty Card” is not returned to Distributor/Dealer or ReneSola;

2) Product is modiﬁed, the design is changed or parts are replaced by an unauthorized party not

pre-approved by ReneSola to speciﬁcally do so;

3) Modiﬁcaons, changes, or aempted repairs are made or serial numbers/seals/cerﬁcaon

marks are erased by an unauthorized technician not pre-approved by Renesola to speciﬁcally

do so;

4) Incorrect installaon or commissioning;

5) Failure to observe the applicable safety regulaons (VDE standards, etc.);

6) The Product has been improperly stored or was damaged while in possession of the Dealer or

end user;

7) A claim to cover transportaon damage or scratches caused by shipping company must be

ﬁled with insurance company when containers are unload and enough evidence is gathered to

support the claim;

8) Failure to observe and follow guidelines in the user manual, installaon guide,

and maintenance regulaons;

9) Incorrect use or inappropriate operaon;

10) Insuﬃcient venlaon of the device;

11) Sub-standard maintenance and service procedures;

12) Force majeure (e.g., lightning, overvoltage, storm, ﬁre).

13) The product is used as the component of a product expressly warranted by another

manufacturer;

Warranty Period: 25-year limited warranty period.

Warranty Time Start: From the date of bill of lading.

Warranty Evidence:The bill of lading date, product(s) serial number(s), and product(s) model

number(s), and a completed warranty card.

Scope: Any damages occurring within the WARRANTY PERIOD will be evaluated by ReneSola

authorized service partners and qualiﬁed ReneSola employees, who will deﬁne the scope and

responsibility taking into account.

9. WARRANTY

Warranty terms of Micro Replus™ Grid-Tied Microinverter

Warranty Condions

8. SPECIFICATIONS

Technical Speciﬁcaons

270

>99.5%

22 ~ 45

225

<4%

>0.95

96.3%

95.0%

<0.17

Yes

NEMA6 / IP66

-40˚c ~ +65˚c

0 ~ 95%

LED Light

PLC (Power Line Communicaon)

230*138*35 mm / 9.06*5.44*1.38 inch

2.0 kg / 4.4 lbs

25 years limited warranty

240

211 ~ 264

59.3 ~ 60.5

186 ~ 228

59.3 ~ 60.5

208

200 ~270 *

45.5 ~ 54.5 *

230

Model

Max. PV-Generator Power (Wp)

Max. DC Voltage (V)

Maximum input short circuit current (A)

MPPT eﬃciency

MPPT DC Voltage Range(V)

Max. Units per Branch Circuit

Nominal AC Power (W)

Nominal AC Voltage (V)

Nominal AC Voltage Range (V)

AC Power Frequency / Range (Hz)

THD (at Nominal Output)

Power Factor (cosφ）

Peak. Eﬃciency

CEC Eﬃciency

Power Consumpon at Night (W)

Over/ Under Voltage Protecon

Over/Under Frequency Protecon

An-Islanding Protecon

Over Current Protecon

Reverse DC Polarity Protecon

Overload Protecon

Degree of protecon

Environment Temperature

Relave Humidity

Display

Communicaon way

Dimensions (WxHxD)

Weight

Warranty

* Detailed parameter please see local grid standard, inverter can match local grid standard automacally.

Input (DC)

Output (AC)

Eﬃciency

Protecon

General Data

Replus-250A Replus-250B Replus-250

10 11

Please report defecve devices with a brief error descripon to our service hotline for inial

problem idenﬁcaon and return the warranty card to our service department by fax/email for

warranty claim. If your claim is approved, ReneSola will generally send an equivalent

replacement device, packaged appropriately for transport, within 7 working days. The defecve

device is to be packed in the original packaging materials for return transport to the closest oﬃce

of Renesola or original installer of your PV system within 30 days of the claim approval date.

• If in-ﬁeld troubleshoong does not solve the problem the claim requests must include the

following informaon:

Defecve Product(s) proof-of-purchase in the form of (1) the dated purchase receipt from the

original purchase of the product at point of sale to the end user, or (2) the dated dealer invoice

or purchase receipt showing original equipment manufacturer status, or (3) the dated invoice or

purchase receipt showing the product exchanged under warranty, using Warranty Card, which

includes, but is not limited to, the following informaon:

Model number of the Defecve Product.

Serial number of the Defecve Product.

Detailed descripon of the defect.

Shipping address for return of the repaired or replacement product (as applicable).

• All Defecve Product authorized for return must be returned in the original shipping container

or other packaging that is equally and suﬃciently protects the product.

• The returned defecve product must not have been disassembled or modiﬁed without the prior

wrien authorizaon of Micro Replus. If ReneSola discovers the products claimed defecve

have been disassembled or modiﬁed without prior ad explicit authorized permission from

ReneSola, this warranty shall be null and void.

14) The product’s original idenﬁcaon (trademark, serial number(s), etc) markings have been

defaced, altered, or removed;

15) The product was installed outside of the country;

16) Any consequenal losses that are aributable to the product losing power whether by

product malfuncon, installaon error, or misuse.

Claims that go beyond the rights cited in the terms of the Product Warranty, in parcular claims

for compensaon for direct or indirect damages arising from the defecve device, for

compensaon for costs arising from disassembly, labor, and installaon, or loss of proﬁts, are not

covered by ReneSola’s warranty. ReneSola is not subject to statutory liability. The Limited

Warranty does not cover costs associated the removal, installaon, or troubleshoong of the

customer’s electrical systems. The Limited Warranty value shall note exceed the original cost of

the original purchase price of current product price, whichever is lower.

ReneSola will make every eﬀort to remedy defects in a mely fashion and without unnecessary

bureaucracy. Please contact our technical department directly for support. Each inverter failure

shall be reviewed in ReneSola’s tesng lab or by an authorized ReneSola service partner, prior to

issuing a service reimbursement to the customer. If an inverter has been modiﬁed,

reimbursement shall be decided upon at the sole discreon of a ReneSola customer service

representave.

Warranty Claim Procedure:

AUSTRALIA

Add: 18 Corporate Blvd. Bayswater, VIC 3153, Australia.

T: +61 481 251 275.

U.S.A

Add: 301 Howard St, Suite 850, San Francisco, CA 94105.

T: +1 415 852 7418

E: [email protected]

Europe

Add: Renesola Deutschland GmbH, Lyoner Strasse 15,60529 Frankfurt/M,Germany

T: +49 69 663 786 9-0

E: [email protected]

APMEA & China

Add: F-15, Manpo Intl. Plaza, No. 500 West Yan'an Rd, Shanghai, China 200050

T: +86 21 6280 9180

F: + 86 21 6280 5600

E: [email protected]

10. CONTACT US

12 13

11. APPENDIX

11.1 Warranty Card

Customer Informaon

Name:

Address:

City: State: Zip Code:

Tel.: Fax: E-mail:

System Informaon

Fault Product(s) Serial Numbers:

System Commissioning Date: Product Models:

No. of Products Used: Bill of Lading Date:

Fault Product(s) Quanes: Fault Time/Date:

Fault Message(s) or Code(s):

Brief Fault Descripon and Photos:

Installaon Informaon

Modules Used:

Modules Quanty: Inverters quanty per string:

Installaon Company Name:

Installer Name:

For the informaon on our warranty terms and condions,

please see our website: www.renesola.com.

All ﬁelds must be completed in order to process claim.

Customer Signature: Date:

14 15

11.2 Examples of connecon diagram

1 2 3 4 5 6 7 8 9 10 11

For EU, AU, CN

AC BOX

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Replus Wechselrichter Handbücher

Replus

Replus IH3KW-48-V Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

Astrel Group

Astrel Group Power Reducer Kurzanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung