Repotec WR5822 Bedienungsanleitung
Quick Installation Guide
V1.0
802.11ac Dual Band Concurrent
Gigabit WLAN Router
802.11ac Dual Band Concurrent GbE WLAN Router
WEEE Directive & Product Disposal
At the end of its serviceable life,
this product should not be treated as household or general
waste.
It should be handed over to the applicable collection point for
the recycling of electrical and electronics equipment,
or returned to the supplier for disposal.
1
R4
802.11ac Dual Band Concurrent GbE WLAN Router
System Requirements
1. Pentium 200MHZ processor or above
2. Windows 98SE, Windows Me, Windows 2000,
Windows XP, Windows Vista, Windows 7, Windows 8, Windows 8.1 and
Windows 10.
3. 64MB of RAM or above.
4. 25MB free disk space
Package Content
1. 802.11ac Dual Band Concurrent GbE WLAN Router
2. CD-ROM (Software & Manual)
3. Quick Installation Guide
4. Ethernet Cable (RJ-45)
5. Power Adaptor
2
802.11ac Dual Band Concurrent GbE WLAN Router
Installation & Setup
Follow each STEP carefully and only go to the next step
once you have completed the previous STEP.
STEP 1
Connection of 802.11ac WLAN AP Router
Step 1. Connect the Ethernet cable to WAN Port
Connect the RJ45 Ethernet cable from your xDSL/Cable Modem's
Ethernet port to 802.11ac WLAN Router's WAN Port.
Step 2. Connect the Ethernet cable to LAN Port
Connect the supplied RJ45 Ethernet cable from your PC's Ethernet
port to any of the 4 802.11ac WLAN Router's LAN Ports.
Step 3. Attach the power connector
Connect the power adapter to the power inlet “POWER” of the
802.11ac WLAN Router and turn the power switch “ON/OFF
SWITCH” of your 802.11ac WLAN Router on.
3
R4
802.11ac Dual Band Concurrent GbE WLAN Router
LED Meaning
Your 802.11ac WLAN Router has indicator lights on the front side. Please see
below for an explanation of the function of each indicator light.
Power indicator
Ethernet Active indicator
Wireless Active indicator
WPS Active indicator
Ethernet Active indicator
Table1. LED function
Label
Color
On
Flash
Off
Green Ready Waiting for device
ready Power Off
Green
The device has a WAN
IP address from
xDSL/Cable Modem
Transmit / Receive
Data
No WAN IP address
from xDSL/Cable
Modem
Green WLAN Ready Transmit / Receive
Data WLAN Off
Green N/A Start WPS pairing
within 2 minutes WPS Idle
Green Ethernet Connected Transmit / Receive
Data Ethernet
Disconnected
The icons appear on the products are for application indication only.
The trademark or intellectual property is belonging to their respective owners.
4
802.11ac Dual Band Concurrent GbE WLAN Router
Connectors
Table 2 shows the function of each connector and switch of the device.
Table 2. Function / Description of Connectors
Connector
Description
ANTENNA
2 fixed Antenna
ON/OFF
SWITCH
Power on / off the device
POWER
Connects to the supplied power adaptor
LAN 4/3/2/1
Connects the device via LAN Ethernet to up to 4 PCs
WAN
Connects the device via WAN Ethernet to xDSL / Cable
Modem
WPS
Press this button for at least 3 full seconds and the WPS
LED will flash to start WPS.
Now go to the wireless adapter or device and press its
WPS button. Make sure to press the button within 120
seconds (2 minutes) after pressing the router's WPS
button.
WLAN
Press this button for at least 3 full second to turn off/on
wireless signals
RESET
Reset button. RESET the 802.11ac WLAN router to its
default settings.
Press this button for at least 6 full seconds to RESET
device to its default settings.
5
R4
802.11ac Dual Band Concurrent GbE WLAN Router
Figure1. Rear View of the 802.11ac WLAN Router
Figure2. WPS/ WLAN button
Figure3. RESET button
6
802.11ac Dual Band Concurrent GbE WLAN Router
STEP 2
Configuration Procedures
Before starting the 802.11ac WLAN Router configuration, please kindly
configure the PC computer as below, to have automatic IP address / DNS
Server.
For Windows 98SE/ME/2000/XP
1. Click on "Start" -> "Control Panel" (in Classic View). In the Control
Panel, double click on "Network Connections" to continue.
2. Single RIGHT click on "Local Area connection", then click "Properties".
7
R4
802.11ac Dual Band Concurrent GbE WLAN Router
3. Double click on "Internet Protocol (TCP/IP)".
4. Check "Obtain an IP address automatically" and "Obtain DNS server
address automatically" then click on "OK" to continue
5. Click "Show icon in notification area when connected" (see screen
image in 3. above) then Click on "OK" to complete the setup procedures.
8
Inhaltsverzeichnis
Andere Repotec WLAN-Router Handbücher
Repotec
Repotec 1T1R Bedienungsanleitung
Repotec
Repotec RP WR0582 ML Bedienungsanleitung
Repotec
Repotec WR1440A Bedienungsanleitung
Repotec
Repotec 300Mbps Wireless-N Broadband Router Bedienungsanleitung
Repotec
Repotec RP-WR1134 Bedienungsanleitung
Repotec
Repotec RP-WR0254 Bedienungsanleitung
Repotec
Repotec RP-WR5441L Bedienungsanleitung
Repotec
Repotec WR3211 ML Bedienungsanleitung
