Change battery
• If the battery voltage is only about 2,5V, the signal“LO”
ashes in the display after operation.
• Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Regular or rechargeable batteries must be disposed of in
an ecologically desirable manner after use. If possible,
they should be recycled. The warranty information does
not apply to possibly provided or installed batteries.
Technical Data
• Range: 100m (free eld)
• Batteries: 3V DC 1x CR2032
• Frequency: 868MHz
• Number of switch programms: 20
CE Declaration of Conformity
REV Ritter hereby declares that the 84474-B
model is in accordance with the underlying
requirements and other relevant provisions
of Directive 1999/5/EC. For the complete CE
Declaration of Conformity please refer to
www.rev.biz under the article in question.
This product is a radio controlled system and
should only be used as this. The buttons of the
remote control could not be used permanently.
WEEE-reference of disposal
In accordance with European defaults used
electrical and electronics devices may no
more be given to the unsorted waste. The
symbol of the waste bin on wheels refers to the
necessity of separate collection. Please help with
environmental protection and see to it that
this device is given to the for this purpose
designated systems of waste sorting if you do
not use it any longer. GUIDELINE 2012/19/EU of
the EUROPEAN PARLIAMENT AND the COUNCIL
of July 04th 2012 about electrical and electronics
old devices.
Batterie-reference of disposal
Batteries and accumulators are not to be dis-
posed of in the normal house waste bin. Every
user is legally obliged, to hand over all batteries
and accumulators, irrespective of whether or not
they contain harmful substances to a communal
collection point in the local town area or to a
trade dealer so that they can be disposed of in
an orderly environmentally friendly manner.
Batteries and accumulators should only be handed
over when they are completely discharged!
Warranty
During manufacturing this REV product is passed
through several quality testing stations which are set up
with newest technology. Should nevertheless a defect
arise, REV oers a warranty to the following extent:
1. The duration of the warranty is 24 months after the
date of purchase.
2. The unit is either repaired or replaced by REV free of
charge or if it can be shown that it has become
unusable during the warranty period due to a
manufacturing or material defect.
3. The liability does not cover transport damages or
damaged incurred through defective installation.
4. If REV repudiates the warranty claim and no objection
is made within 6 months, the right to repair becomes
time-barred.
5. In a warranty case the unit must be sent to the dealer
or REV together with the sales slip and a short
description of the defect.
6. If there is no proof for a warranty liability being in
place, any repair carried out will be invoiced.
Basic function
• The radio-operated remote control unit (the
transmitters) controls power sockets and dimmers (the
receivers) selectively and in groups.
• Direct line-of-sight connection between transmitters
and receivers is not necessary, because contact is made
by radio signals.
Positioning
• Do not locate receivers in the corners of rooms.
• Minimum distance between receivers: 1.00m.
• Avoid thick reinforced concrete walls.
Safety
• Read these instructions carefully before starting use.
• Check all components for any signs of damage.
• If any damage is found, don’t connect the product to the
power supply and don’t use it.
• Don’t open the housing.
• Don’t attempt to make any repairs yourself.
• Use the components only in the conditions described in
the technical data.
• Take great care when allowing children to use them.
• Only operate in dry rooms.
Startup
• Remove battery insulation strap.
• Assembly as per gure
To set-up article 0086190103, a suitable iComfort frame is
needed.
Teaching
• All receivers must be programmed onto the button to
which it is meant to react.
1. The programming mode is activated for about 1 minute
by pushing the„LEARN“ button of the product for about
2 seconds. Thereby the red LED is ashing with a
frequency of 1Hz.
2. Now the device must be chosen on the remote control
and transmitted to the receiver by pushing the ^-button.
• After 10 programmings the memory is full.„FU“ appears
on the display.
Adjust time and weekday
• Push button several times until symbol appears
(pic. 3).
• The weekday ashes. Adjust weekday and
conrm (pic. 4).
• The hour ashes. Adjust hour and conrm
(pic. 5).
• The minute ashes. Adjust minute and conrm
(pic. 6).
Finish settings .
Adjust switch programs
In a switch program the switch times for„Open blind“ and
„Close blind“ can be selected. Switch times can be assigned
to a particular weekday or a group of weekdays.
You can adjust 20 switch programs. They run parallel in the
Auto-mode.
Important: Day and group respectively within a switch
program must be the same. Avoid an overlapping of
dierent switch programs.
• Push button several times until symbol appears (pic 7).
• Select switch program and conrm (pic. 8).
• Select function„Open blind“ and conrm (pic. 9).
• The hour ashes. Adjust hour and conrm
(pic. 10).
• The minute ashes . Adjust minute and conrm
(pic. 11).
• The weekday ashes. Adjust weekday or group.
Conrm 2x (pic. 12).
• Select„Close blind“ and conrm . Adjust hour,
minute and weekday or group respectively as above
(pic. 13).
• Quit (pic. 14).
• Continuing with programs 02 to 20. Push button .
Choose programm 01, 02, 03,... with button (pic. 14).
Delete
• Delete all: Push Reset-button with paper clip.
All settings are deleted (pic. 15).
• Delete single switching operations: Select respective
switching operation and delete (pic. 16).
• Delete teached devices: Press key until the
display shows„Clr“
Use operation modes
Automatic mode
• Push button several times until symbol appears.
The switch programs run. (Pic. 20).
Manual mode
• Push button several times until symbol appears
(pic. 21).
The switch programs are out of service.
• Close blind: Push button 1x (pic. 22).
Stop ahead of time: Push button again (pic. 22).
• Open blind: Push button 1x (pic. 23).
Stop ahead of time: Push button again (pic. 23).
Random mode
• Function: the switch programs are randomly delayed for
5 to 30 minutes. Precondition: At least one switch
program must be adjusted.
• Activate random mode: Push button several times
until symbol appears (pic. 24).
ENGLISH
868MHz
REV Ritter GmbH • Frankenstr. 1-4 • D-63776 Mömbris
Tel. +49 900 117 1070 • E-Mail: service@rev.biz • www.rev.biz
ENGLISH
ANL_84474-B.indd 4 03.12.2015 08:52:09
