REXROTH CS 550i Gebrauchs- und Pflegehandbuch

CS 550i/150RC

Spreader and Joystick Controller Calibration Manual

2/44

Bosch Rexroth Canada ı May.2018 ı Revision 7.0

Operator Screen Layout

Programming Mode

Program Screen Layout

Changing Fields –Data Entry

Initial Set-up

Selectable Profile Set-up

6.1

Set-up

6.2

Selecting a profile

Ground Speed Calibration

Valve Nulling –Conveyor/Spinner/Prewet/Norm

8.1

Auto Nulling

8.2

Manual Nulling

Gate Calibration

10.1

10.2

Lane Calibration

Half Lane

One Lane

Material Calibration

Material Catch Test

Load Parameters

Advanced Features

GPS Options and WiFi Data Transfer

15.1

GPS-Passive GPS Tracking

15.2

AVL-Active Vehicle Locator

15.3

Wifi Setup

15.4

Wifi Data Transfer Program

Optional Modes and Operation

16.1

Pattern/Chute Mode

16.2

Air Gate Mode

16.3

Liquid+ Mode

16.4

Cross Conveyor

16.5

Spinner Reverse Mode

16.6

Spinner & Conveyor Reverse mode

16.7

Solid reduction for Prewet

16.8

Dedicated 3 Boom Anti-ice

Optional Modes and Operation - 550 Lite

17.1

Liquid –1 Boom Anti-icing

17.2

Liquid –Dedicated 3 Boom Anti-icing

Error Codes

Joystick Calibration

19.1

Joystick Solenoid Nulling

19.2

Joystick Emergency (Panic Button) –If Equipped

3/44

Bosch Rexroth Canada ı May.2018 ı Revision 7.0

Bosch Rexroth Canada Corp. reserves the right to revise this information at any time and for any

reason and reserves the right to make changes at any time, without notice or obligation, to any of the

information contained in this piece of literature. The information shown in this manual features the

latest version of software as of publication; therefore, some features shown will not exist on older

versions of software in use by some customers.

Please check for updates at: www.boschrexroth.ca/compu-spread

Joystick Min/Max/Emg Setup

Advanced Joystick Set-up

21.1

Power Float

21.2

Mode Names

CS-150 RC Standalone

22.1

Multi Axis Single Stick

22.2

Dual Sticks

Warning

4/44

Bosch Rexroth Canada ı May.2018 ı Revision 7.0

1Operator Screen Layout

SPNR

SALT - -

LIQUID1

Spinner Label

Spread Width %

Spinner Setpoint

Spinner Mode

Pause Button

Solid Name

Gate Mode/Solid Rate

Gate Position/Conv Set.

Conveyor Mode

Blast Button

Liquid Name

Liquid Rate

Liquid Setpoint

Liquid Mode

Reverse Button

Trip Summary

Toggle between Total and Spreading Distance (S)

Total Quantity

Total Prewet Volume

Total Anti-icing Volume

5/44

Bosch Rexroth Canada ı May.2018 ı Revision 7.0

2Programming Mode

All symbols on the right of the screen require a tap and hold for >1 second.

Note: A valid PROGRAMMING USB key must be on the USB port. The PROGRAMMING

USB key is for programming (v82 or newer), and the LOG DATA USB key is only for

retrieving data.

Press symbol to enter into programming mode.

6/44

Bosch Rexroth Canada ı May.2018 ı Revision 7.0

3Program Screen Layout

Note: Due to the compact nature of these screens, the use of a selection tool like a stylus is

recommended.

7/44

Bosch Rexroth Canada ı May.2018 ı Revision 7.0

4Changing Fields

Note: Due to the compact nature of these screens, the use of a selection tool like a stylus is

recommended.

When selecting an item without a pull-down selection menu, a keypad is required. This

keypad is used to enter text or numeric values. The example shown is “TRUCK-ID”.

8/44

Bosch Rexroth Canada ı May.2018 ı Revision 7.0

5Initial Set-up

1. Set the units to imperial (LBS/Mile) or metric (Kg/Km).

2. Set the TRUCK ID.

3. Set the REGION NAME.

4. Set the DRIVER ID (optional), 4 driver IDs allowed.

Note: Configuring 4th driver ID to ‘USER” enables operators to enter user defined driver

ID on operator screen.

5. Set the type of Temperature Sensor (optional).

6. Set the Options –see Advanced Features on page 14 (optional).

7. Set the items that the user has access to (optional).

8. Set Blast Timer, 0-timer disabled (optional). This should be set less than Err01 delay.

9. Set Percentage of Temp. compensation when there is a 3 degree change (optional).

10. Set the vehicle speed alarm (optional).

11. Select AVL or GPS tracking (optional).

12. Set WIFI/TIME/STYLUS (if required). Note: Save only applies to changes to

Date/Time/WiFi/Stylus.

The default error configuration values will work well for most applications, no changes

required.

9/44

Bosch Rexroth Canada ı May.2018 ı Revision 7.0

6Selectable Profiles

6.1 Set-up

Different profiles for the truck can be set up and saved for later use. Each profile can

have a unique name such as ‘Sander’ with its own settings and calibration. Warning:

truck must be wired to match different configurations, make sure wired properly before

changing.

1 Set Truck ID to ‘SETUP’

2 Enter a name for the profile in Region

3 Using the green selector arrow, set the 4th Driver ID to ‘USER’

4 Calibrate the system

5 Exit to Operator screen

6 Save the profile to USB

7 Repeat these steps to set up other profiles

8 Change both Truck ID and Region to the desired names that are different from all

the user configured profile names

6.2 Selecting a profile

1 Click on the Driver ID field on the Operator screen, keypad will pop up.

2 Enter the name of the profile needed such as ‘Sander’ or ‘Anti Ice’

3 Press ‘Enter’

4 REBOOT SYSTEM TWO TIMES for changes to take effect.

4th drivrID Set To ‘USER’

Truck ID Set To ‘SETUP’

USER defined PROFILE

10/44

Bosch Rexroth Canada ı May.2018 ı Revision 7.0

7Ground Speed Calibration

1. Select symbol to enter into the ground speed calibration screen.

2. Choose which calibration option best suits your situation.

3. Follow the instructions on the screen.

Driver ID

‘Enter’

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere REXROTH Controller Handbücher

REXROTH

REXROTH IndraDrive HCQ02 Technisches Handbuch

REXROTH

REXROTH VT-HACD-DPQ Series Gebrauchsanweisung

REXROTH

REXROTH IndraControl L25 Series Technisches Handbuch

REXROTH

REXROTH IndraDrive Mi Bedienungsanleitung

REXROTH

REXROTH CS 550/150 Gebrauchs- und Pflegehandbuch

REXROTH

REXROTH IndraDrive C Series Technisches Handbuch

REXROTH

REXROTH ECODRIVE03 Bedienungsanleitung

REXROTH

REXROTH VT-HACD-3-2 Series Bedienungsanleitung

REXROTH

REXROTH IndraDrive M Technisches Handbuch

REXROTH

REXROTH CS 520 Merkblatt

REXROTH

REXROTH CS 530 Merkblatt

REXROTH

REXROTH IndraDrive Fc FCS01 Bedienungsanleitung

REXROTH

REXROTH HCS03 Bedienungsanleitung

REXROTH

REXROTH EcoDrive 03 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung