REXROTH CS 550/150RC Bedienungsanleitung
CS 550/150RC Towplow
Spreader Joystick Controller Operator Manual
2/17
Bosch Rexroth Canada ı August.2018 ı Revision 2.0
Table of Contents
1
Panel Controls
3
2
Operation Screen Layout
4
3
Screen Controls
5
3.1
Pause
5
3.2
Blast
5
3.3
Reverse
5
3.4
Change Solid /Prewet Material
6
3.5
Manual Gate Adjustment
6
3.6
Simulated Ground Speed
7
3.7
Error Messages
7
3.8
TOW 3 Boom Anti-icing (DLA)
8
4
Symbol Actions
9
4.1
Error Log/Diagnostic –Gear Symbol
9
4.2
Unloading –UNLOAD Symbol
10
4.3
Data Retrieval/Clear Trip Summary –USB Symbol
10
4.4
Brightness/Volume Adjustment –Backlight Symbol
11
4.5
Manual Hydraulic Gate Adjustment –Cylinder Symbol
11
4.6
Programming Mode –Lock Symbol
12
5
Operator ID Input
13
6
Joystick Control
13
6.1
Joystick Screen
13
6.2
Button Status
13
6.3
Joystick Status
14
7
Spinner Reverse Mode
14
8
Air Gate Mode
15
9
Error Codes
15
10
Warning
17
Bosch Rexroth Canada Corp. reserves the right to revise this information at any time and for any
reason and reserves the right to make changes at any time, without notice or obligation, to any of the
information contained in this piece of literature. The information shown in this manual features the
latest version of software as of publication; therefore, some features shown will not be available on
older versions of software in use by some customers.
Please check for updates at: www.boschrexroth.ca/compu-spread
3/17
Bosch Rexroth Canada ı August.2018 ı Revision 2.0
1Panel Controls
Turn knobs clockwise to increase.
4/17
Bosch Rexroth Canada ı August.2018 ı Revision 2.0
2Operation Screen Layout
SPNR
SALT - -
LIQUID1
Spinner Label
Spread Width %
Spinner Setpoint
Spinner Mode
Pause Button
Solid Name
Gate Mode/Solid Rate
Gate Position/Conv Set.
Conveyor Mode
Blast Button
Liquid Name
Liquid Rate
Liquid Setpoint
Liquid Mode
Reverse Button
5/17
Bosch Rexroth Canada ı August.2018 ı Revision 2.0
3Screen Controls
3.1 Pause
Press the Pause button to pause, and press again to resume spreading.
3.2Blast
Press the Blast button to increase the spreading output, and press again to resume regular
rate.
3.3 Reverse
Press and hold the Reverse button to change the direction of the Auger (an optional feature
to dislodge obstructions). Release the button to resume spreading.
6/17
Bosch Rexroth Canada ı August.2018 ı Revision 2.0
3.4 Change Solid/Liquid Material
Press the oval button with “SALT- -” text on it to adjust material type. (Note: Vehicle must
be stationary) Use the left and right arrows to change.
Use the Left and Right to
adjust
Press the oval button again
to confirm and save the
selection.
Press the oval button with the “LIQUID1” text to adjust the material type. (Note: vehicle
must be stationary)
Use the Left and Right
arrows to adjust.
Press the oval button again
to confirm and save the
selection.
3.5Manual Gate Adjustment
For Manual Gate operation ONLY.
Press the Gate Position
Number to select the gate
adjustment mode.
Use the up and down arrows
to adjust.
Press the Gate Position
again to verify the selection.
7/17
Bosch Rexroth Canada ı August.2018 ı Revision 2.0
3.6 Simulated Ground Speed
This function is available when a truck is stationary. Tap on the ground speed ‘0’, pop up
the UP/Dn arrows, press & hold the UP arrow for 5 seconds to enable the simulated
ground speed.
Use the up and down arrows
to adjust speed with an
increment of 5.
3.7 Error Messages
During the operation when an error occurs, a message will appear in the centre of the
screen. Tap anywhere on the message to clear the window.
8/17
Bosch Rexroth Canada ı August.2018 ı Revision 2.0
DLA rate
change
Left
Boom
Centre
Boom
Right
Boom
DLA
Material
Truck
Status
TOW
Status
3.8 TOW 3Boom Anti-icing (DLA)
If the TOW is configured as 3 Boom Anti-icing (DLA) the SPINNER AND CONVEYOR will
be disabled.
Note: Only external boom switches are supported for TOW 3Boom Anti-icing operation.
To check the read-time status of the TOW 3Boom Anti-icing press the ‘Gear’
symbol at the top right of the screen when a vehicle is moving.
9/17
Bosch Rexroth Canada ı August.2018 ı Revision 2.0
4 Symbol Actions
All symbols on the right of the screen require a press and hold for >1 seconds.
4.1 Error Log/Diagnostic
When the vehicle is stationary press the ‘Gear’ symbol to display most recent error
messages. If a hydraulic pressure&temperature sensor is connected both readings will be
displayed on the bottom right of the screen.
A program key is required to clear the error log; hold the button for >5 seconds.
When a vehicle is moving press the ‘Gear’ symbol to display the real-time status of
spreading.
Err/Diag Unload USB Bright/Vol Cylinder Lock
Parm file name
downloaded last
(firmware build38
or newer)
10/17
Bosch Rexroth Canada ı August.2018 ı Revision 2.0
4.2 UNLOADING
Press the ‘Unload’symbol to enter into unload mode. (Note: The vehicle must be
stationary.)
Turn the dials until the
desired speed is achieved.
Press the symbol again and
to exit unload mode. Moving
the vehicle will suspend the
unload process. It will
automatically resume when
the truck is stopped again.
4.3 Data Retrieval/Clear Trip Summary
With a ‘LOG DATA KEY’
inserted
Press the ‘USB’symbol to
transfer the log data.
Andere Handbücher für CS 550/150RC
1
Inhaltsverzeichnis
Andere REXROTH Videospiel-Controller Handbücher
Beliebte Videospiel-Controller Handbücher anderer Marken
Hyperkin
Hyperkin Smartboy Bedienungsanleitung
Nerf
Nerf DuraGrip Bedienungsanleitung
MoveMaster
MoveMaster MoveMaster Bedienungsanleitung
WinWing
WinWing Super Libra J1 Bedienungsanleitung
ECCI
ECCI Trackstar 6000 Series Bedienungsanleitung
Logitech
Logitech 963291-0403 - Attack 3 Joystick Bedienungsanleitung