RF SOLUTIONS MAINSLINK–PRO Bedienungsanleitung
MAINSLINK–PRO
DS-MAINSLINKPRO-2
•
•
•
•
•
•
•
•
•
•
•
MAINSLINK-PRO
DS-MAINSLINKPRO-2
PATENT PENDING
Application example: WORCESTER-BOSCH Boiler Installation
Warnings :
• Product is not independently isolated, ISOLATE the mains electricity supply before
removing the cover and observe any relevant safety precautions. Maintenance to the
product that involves removal of the cover should only be carried out by a competent
person or qualified electrician.
• F2 Fuse rating is 4A (T) 250 H (Ceramic). Replace fuse with same type and rating.
• Relay is rated at 10A peak, and 5A constant.
• Product must be connected to a switch fused (spur/supply) or BS 1363 Plug. It is
recommended a single Fuse Spur is used to supply the Boiler and MAINSLINK-PRO
jointly so that they are isolated together
CH ON
DHW
ON
A
B
This system provides two functions, Switching of the Pump from the boiler and Switching of the
Boiler from the wiring Centre.
Connections at the Boiler
The boiler output to the Pump is connected to the MAINSLINK-PRO A, (Lin)
The boiler switching input is connected to the MAINSLINK-PRO A (Lout)
It is recommended to use a single switch fuse spur to supply the Boiler and Mainslink together. (so
that both appliances are isolated together)
Connections at the Wiring Centre
The thermostats switching output to switch the boiler is connected to the MAINSLINK-PRO B (Lin)
The Pump is connected to the MAINSLINK-PRO B (Lout)
Operation
When the wiring centre commands the Boiler ON MAINSLINK-PRO B (Lin) is switched is Live then
MAINSLINK-PRO A Lout will automatically switch a LIVE signal to turn the boiler on.
When the Boiler switches the Pump drive ON MAINSLINK-PRO, (Lin) “A” is switched Live then
MAINSLINK-PRO
DS-MAINSLINKPRO-2
PATENT PENDING
SWITCHED LIVE
N N L
Permanent
LIVE FEED
Lin (LIVE IN)
PERMANANT
SUPPLY
Lout (LIVE OUT)
Lin
Comm
Lout
WDOG
MODE
MOM/LAT
MAG Switch
Installation
Connect the Supply to both units
Connect the permanent LIVE and NEUTRAL supply.
Comms LED
Check the Green LED is always ON when both units are powered
Connect the Switched Input L in
When the Switched Live input (LIN) is ’LIVE’ the Red Lin will illu-
minate, and the L out at the other unit will then switch Live out
Connecting the Switching Load L out
Connect the LOAD Live to Lout
When the Switched Live Output (LOUT) is ’LIVE’ the Red L OUT
LED will illuminate
LED Off On Flashing
L in No Input LIVE input at
terminal
Comms RF Link Healthy See Comms
LED Table
L out Output is
OFF Output is LIVE
Watchdog Signal
MAISNLINK-PRO automatically transmits an rf ‘watchdog’ signal every ~30secs in the back-
ground. If the WDOG signal is not received within 90seconds, the output will drop out and
comms LED will flash.
This provides improved reliability and security useful in noisy or poor reception areas.
Multiple System Operation:
Each MAINSLINK-PRO system contains a unique identity so multiple systems can operate within
the same area without interfering with each other.
Comms LED
The Comms indicates the status of the MAINSLINK-PRO
COMMS LED Table
ON One Flash Two Flashes 3 Flashes
Operation
Status RF Link
Healthy Out of range Powered
But unpaired In Pairing Mode
Descrip-
tion
System
operating OK
No RF connection
to other
MAINSLINK-PRO
Waiting to be paired
to another
MAINSLINK-PRO
Actively sending an
RF ‘Please Pair
message’
MAINSLINK-PRO
Disclaimer:
Whilst the information in this document is believed to be correct at the time of issue, RF Solutions Ltd does not accept any liability whatsoever for its accuracy, adequacy or completeness. No
express or implied warranty or representation is given relating to the information contained in this document. RF Solutions Ltd reserves the right to make changes and improvements to the
product(s) described herein without notice. Buyers and other users should determine for themselves the suitability of any such information or products for their own particular requirements or
specification(s). RF Solutions Ltd shall not be liable for any loss or damage caused as a result of user’s own determination of how to deploy or use R F Solutions Ltd’s products. Use of RF
Solutions Ltd products or components in life support and/or safety applications is not authorised except with express written approval. No licences are created, implicitly or otherwise, under any
of RF Solutions Ltd’s intellectual property rights. Liability for loss or damage resulting or caused by reliance on the information contained herein or from the use of the product (including
liability resulting from
negligence or where RF Solutions Ltd was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict QuasarUK Ltd’s liability for death or
personal injury resulting from its negligence.
Important European compliance information
This RF Solutions product meets the essential requirements of the European Radio Equipment Di-
rective 2014/53/EU and has been tested to European Harmonised Standards and CE marked accord-
ingly. A copy of the EU Declaration of Conformity can be located on the RF Solutions Website,
www.rfsolutions.co.uk/certification-i59.
36.00
88.00
88.00~25.00
30.00
Dims in mm
Fixing Instructions:
1.Fix the rear of the MAINSLINK-PRO enclosure to the wall using the template above.
2.Ensure that all fixing screws are screwed flush to the enclosure.
3.Ensure that the screw covers are put in place. These ensure water proofing and insulate the
PCB from the wall fixing screws. Screw Covers are found inside the rear of the enclosure.
4.Once the enclosure is fixed to the wall, screw on the front plate with the PCB in place.
Dimensions and Wall mounting information:
MAINSLINK-PRO is a professional use product and should only be installed by a competent
person. The product must be FIXED to the wall (EN60950 4.1)
RF Solutions Ltd. Recycling Notice
Meets the following EC Directives:
DO NOT
Discard with normal waste, please recycle.
ROHS Directive 2002/95/EC
Specifies certain limits for hazardous substances.
WEEE Directive 2002/96/EC
Waste electrical & electronic equipment. This product must be disposed of through a licensed WEEE collection point. RF
Solutions Ltd., fulfils its WEEE obligations by membership of an approved compliance scheme.
MAINSLINK-PRO
DS-MAINSLINKPRO-2
PATENT PENDING
1. Apply a 230Vac supply to the first MAISNLINK-PRO
2. Briefly place a magnet across enclosure (top left corner
as shown) to activate the internal reed switch.
3. The GREEN comms LED will flash 3 times to show in Pair-
ing Mode
Advanced Operation—Pairing together two MAINSLINK-PROs
NOTE: This system does not require pairing , they are supplied ready to operate!
This process is described for advanced use only.
Erasing a MAINSLINK-PRO
3. Apply 230Vac to the second MAINSLINK-PRO
4. Briefly place a magnet across enclosure (top left corner as
shown) to activate the internal reed switch.
5. The GREEN comms LED will flash 3 times to show in Pairing
Mode
6. The two MAINSLINK-PRO units which will now auto pair to-
gether (allow 30 secs -Green Comms LED will stay on.)
To erase the system hold a magnet beside the top left
corner of the enclosure for 10 seconds as shown.
Repeat this process on both units to erase system.
Technical Specification:
Dimensions: 88 x 88 x 54mm
Electrical Characteristics Min Typical Max Units
Supply Voltage TX/RX: 100 230 250 Vac
Operating Frequency* 869.50 MHz
RF Output power +20 dBm
Bandwidth (Spreading Factor) 60 KHz
Maximum switching load (RX) 1000 W
Time delay from Tx Transmit to Rx Relay
operation:
Mode 3
Mode 7
3
4
Secs
MAINSLINK-PRO
DS-MAINSLINKPRO-2
PATENT PENDING
Jumper Link Setting
There are three Jumper Links which may be used to configure the following
Link Open Fitted
WDOG Watchdog Active
MODE LORA Mode 3 LORA Mode 7
MOM/LAT Momentary Latching
N N L
Permanent
LIVE FEED
Lin (LIVE IN)
Lout (LIVE OUT)
Lin
Comm
Lout
WDOG
MODE
MOM/LAT
WDOG - WATCHDOG
When the WDOG link is fitted each MAINSLINKPRO automatically sends a background watch-
dog RF signal and expects to receive a corresponding WDOG signal from its partner.
If the WDOG signal is not received within 90seconds, the output will drop out and comms LED
will flash.
This provides improved reliability and security useful in noisy or poor reception areas.
MODE
LORA Mode 3, Faster operation shorter range (Line of sight upto 3Km / 500m in buildings)
This mode is recommended for general operation,
LORA Mode 7, Slower operation Long range (Line of sight upto 5Km / 1Km in buildings)
This mode can be used where additional RF penetration / range is required
Note! In this mode a transmitted signal can take 2 seconds to trigger the receiver.
MOM/LAT - Momentary or Latching
Sets the Relay changeover contacts to operate as Momentary or Latching.
MOMENATRY: used for MAINSLINK TO MAINSLINK
LATCHING: is used when MAINSLKINK is being controlled from an RF Solutions hand held Re-
mote transmitter.
Switching Lower Power LED Lights
Mainslink incorporates a “snubber” protection circuit which
is recommended when motor switching. This is incorpo-
rated when Jumper Link J2 is connected between pins 1 & 2
(horizontally across the top pins)
If using MAINSLINK to switch lower power LED lighting the
snubber circuit can cause the LED lights to faintly glow.
To remove this the snubber circuit can be removed by taking
out the Snubber Jumper link as the image shows
Inhaltsverzeichnis
Andere RF SOLUTIONS Fernbedienung Handbücher
RF SOLUTIONS
RF SOLUTIONS HORNETPRO-8S1 Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS HORNETPRO Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS Hornet-S1 Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS HORNETPRO Series Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS PRO Series Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS FOBBER-8T6 Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS TRAP Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS ELITE Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS EZTEXT Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS ELITE Series Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS EZTEXT Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS TRAP Series Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS FOBOEM-4S4 Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS TRAP Series Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS Keeloq FOBLOQA-4T1 Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS EZTEXT-DIN Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS TRAP-SHUFFLE Game Simulator Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS PRO Series Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS HORNETPRO MAINS Bedienungsanleitung
RF SOLUTIONS
RF SOLUTIONS QUANTAFOB Bedienungsanleitung
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
