RF RFT-847CI Bedienungsanleitung

RFT-847CI

DVB-S/S2 to IP streamer

User Manual

RF-Tuote Oy, Joensuunkatu 13, 24100 Salo, tel. +358-2736 6360, fa . +358-2-736 6360, info@rf-tuote.fi, www.rf-tuote.fi

1. Purpose of use

RFT-847CI is HD compatible IP streamer designed for a processing four 8PSK/QPSK modulated satellite

signals (DVB-S/S2) to data broadcast (IP) connected to Ethernet.

With one RFT-847CI unit can be transmitted up to 8 programs (max. average bit rate 5Mbit/s/program)

when there are 8 or more simultaneous users (Multicast). When there are 7 or less simultaneous users, 40-

50 SD programs (total bit rate 40 Mbit/s) can be transmitted (Unicast). The programs can be received

withVideolan's VLC Media Player (www.videolan.com), IP STB or Smart TV.

2. Installation

The connections are shown in Fig 1.

1. RJ 45 output connector to Ethernet

2. Not in use

3. Not in use

4. F-female for input of tuner 3 and 4 (DVB-S/S2)

5. F-female for input of tuner 1 (DVB-S/S2

and tuner 2 (DVB-S only)

6. 2* CAM slot; right slot (connector side) is for

tuner 4 and left side slot is for tuner 3

7. DC IN

8. DC OUT for next RFT-847 unit (max 8 units in

chain)

RFT-847CI is mounted directly on the wall. Do not cover the air passage holes.

Signal from LNB is fed to F-female connectors 4 and 5. Tuners 1 (DVB-S/S2) and 2 (DVB-S only) are

connected to connector 5 and tuner 3 and 4 (DVB-S/S2) are connected to connector 4.

Tuners 1 and 2 are only for FTA channels.

Maximum total current of LNB connector is 250 mA.

Power supply unit is connected to the left side DC connector of RFT-847CI at the bottom of unit (7). You

can loop-through DC from the right side DC connector (8) to next unit with the DC cable. Maximum eight

RFT-847CI units in chain can be supplied with one power supply.

Ethernet cable is connected to RJ 45 connector (1).

3. Setting up the system

This manual is only for main functions of RFT-847CI unit. The other functions are purposed only for

advanced users.

RF-Tuote Oy, Joensuunkatu 13, 24100 Salo, tel. +358-2736 6360, fa . +358-2-736 6360, info@rf-tuote.fi, www.rf-tuote.fi

The system is programmed with PC via Web browser. There are two options.

Option 1. Setting IP address with DHCP and accessing by using UpnP protocol

1. Connect Ethernet cable from RFT-847CI to the existing LAN with a router

2. RFT-847CI is recognised automatically by router. In some routers power must be switched OFF and

again ON

3. Go to Network Task and double click “Show icons for networked UpnP devices”. Then you see that

RFT-847CI is connected network.

4. Double click RFT-847CI to get the web access.

5. When prompted for the login and password, then write “webadmin” for both. Then you see the main

menu (see below).

Option 2. Setting RFT-847CI via default IP address

1. Connect Ethernet cable from RJ 45 connector to computer.

2. The factory set IP address of each RFT-847CI is 172.16.1.1 and subnet mask is 255.255.255.0.

3. Set the IP of PC to e.g 172.16.1.2 and sub net mask to 255.255.255.0.

4. Open the web browser like IE, Firefox, Opera etc…

5. Write to address field 172.16.1.1 and then enter.

6. Set log in and password “webadmin” for both. Then following screen displays.

This screen is the default entry to the HTML interface.

The menu structure is in three levels e.g SYSTEMNETWORK Status. The selected option is

highlighted.

RF-Tuote Oy, Joensuunkatu 13, 24100 Salo, tel. +358-2736 6360, fa . +358-2-736 6360, info@rf-tuote.fi, www.rf-tuote.fi

4. DVB configuration

4.1 Satellite tuner

To set satellite tuner parameters go to TUNER Update

Select Tuner 1 (DVB-S/S2) and set correct parameters. Then press “Update”, The “Status” screen displays.

NOTE! 1. Note a dot (.) when frequency is entered in GHz.

2. When DVB-S2 (HD) programs are received, tick firstly “DVBS2” Mode” and then “Apply”.

RF-Tuote Oy, Joensuunkatu 13, 24100 Salo, tel. +358-2736 6360, fa . +358-2-736 6360, info@rf-tuote.fi, www.rf-tuote.fi

Check that signal and data are locked and signal strenght is acceptaple . The acceptable range (green beam)

is 22…88% (-70… -25 dBm). Yellow beam means that signal range is out of acceptaple range.

Note! The beam “meter” is only directive. Go to STREAMING/PROGRAMS/Update and check if channels

are in the list.

When settings are ready, go to TUNERMANAGE and select Save Session.

IMPORTANT! Save Session must be selected for each tuner separately.

The settings of tuner 2 (DVB-S/S2) and tuners 3 and 4 (DVB-S only) are made similar way.

5. Streaming to network

RFT-847CI devices are capable of streaming DVB-S/S2 video and audio broadcasts into your system for

unicast or multicast redistribution. Streaming is enabled after the device is tuned to an DVB-S/S2

transponder. Follow the instructions in the next sub-sections to configure the device for streaming as per

your needs.

Select the

STREAMING/PROGRAMS

Update

window. A list of all stations broadcasting through the

transponder displays on screen.

- In “Audio” column, select the type of audio stream.

- The “IP” column shows the destination IP address where the stream is to be sent inside your network.

Input the correct address of the receiving station.

RF-Tuote Oy, Joensuunkatu 13, 24100 Salo, tel. +358-2736 6360, fa . +358-2-736 6360, info@rf-tuote.fi, www.rf-tuote.fi

- The “Port” column shows the conduit through which the stream is transmitted into the network. Usually,

all streams are set to go through the same port. However, you can configure a different port for each station

broadcasted to the same IP address, so as to transmit different stations to that same address.

Note: To allow viewing different brodcasted stations simultaneously, ensure that unique pairs of IP

addresses and port numbers are input. You may pair one single IP address with different port numbers, or

different IP adresses with one single port number. If you set the system to stream broadcasts only when at

least one listener is present (that is, if the IGMP function is enabled), different multicast IP addresses must

be set in the configuration

- In the “Action' column” press the

TART

button corresponding to the desired station. The

Update

window

refreshes, the selected station's name turns blue, the 'Audio Track', 'IP' and 'Port' fields become dimmed, and

the 'Action' button becomes blue and reads

TOP.

- Select the

Status

option to review the streaming status. A screen displaying the selected parameters and the

current streaming status displays. (When IGMP is enabled, the ‘Status’ column shows ‘

Waiting

’ for streams

that have been started at the

STREAMING

PROGRAMS

Update

window but are not being listened to).

To stop streaming, go to the STREAMING/PROGRAMS/Update window and press the relevant STOP

button. The information for the corresponding station reverts to its original color and status.

Select the

STREAMING/MANAGE

Operation Mode

window.

RFT-847CI streamer can operate in one modes:

Streaming and DataCasting in addition to streaming video and audio broadcasts, the

RFT-847 device also supports the reception of DVB-S/T-transmitted data IP PIDs; this is executed through

the DVB-S-T/PID/Update window.

Note: The Streaming and DataCasting mode of operation supports only up to 8 PIDs in all. When operating

in this mode, the quantity of audio/video broadcasts to be streamed is reduced according to the quantity of

data IP PIDs being received. For example, if you set the system to receive 2 IP PIDs, only up to 3

broadcasts with audio and video PIDs become available.

RF-Tuote Oy, Joensuunkatu 13, 24100 Salo, tel. +358-2736 6360, fa . +358-2-736 6360, info@rf-tuote.fi, www.rf-tuote.fi

RFT-847CI allows you decide whether streams are to be forwarded into the LAN only when at least one

listener (that is, an entity actually connected to the stream) is identified, or at all times. Making streaming

conditional to the identification of listeners leads to a better use of the existing bandwidth since it ensures

that the stream is actually in use. Stream distribution is regulated through IGMP (Internet Group

Management Protocol).

Select the

STREAMING/MANAGE

IGMP

window

To enable the IGMP function and have streams forwarded only if at least one connected suscriber is

identified, select the 'Stream Programs Only if Listener Exists (Enable IGMP)' radio button and press the

UBMIT T button. The screen shows the current IGMP status as "Enabled" and offers the possibility of

disabling IGMP (‘Stream Programs Regardless of Listeners’ radio button).

To disable the IGMP again, select the ‘Stream Programs Regardless of Listeners’ radio button and press

UBMIT. The screen reverts to its original status.

RF-Tuote Oy, Joensuunkatu 13, 24100 Salo, tel. +358-2736 6360, fa . +358-2-736 6360, info@rf-tuote.fi, www.rf-tuote.fi

Once streaming parameters (audio track, destination IP address, port) have been set and there is no intention

to change them, it is possible to activate streaming from the IP media player used to view the broadcasts.

Follow the instructions below to configure the option to set streaming on demand:

Select the

STREAMING/MANAGE

OnDemand

window

To enable the IGMP On Demand function and have streams continually ready to be started at the IP media

player, select the 'Enable IGMP OnDemand Streaming' radio button and press the S

UBMIT

button. The

screen shows the current Enable On-Demand Streaming status as "Enabled" and offers the possibility of

disabling this feature (‘Disable OnDemand Streaming’ radio button). These option allows to user to receive

random programs list without to start each program manually.

To enable the VbTV On Demand function, select the 'Enable VbTV OnDemand Streaming' radio button

and press the SUBMIT button. The screen shows the current Enable VbTVOn-Demand Streaming status as

"Enabled" and offers the possibility of disabling this feature (‘Disable OnDemand Streaming’ radio button).

To initiate streaming, go to the IP media player and select the desired station from the list, activating it as

per the specific media player’s features. Please note that when OnDemand is enabled, no changes can be

made to the streaming configuration set in the STREAMING/PROGRAMS/Update window.

To disable the OnDemand feature, return to the STREAMING/PROGRAMS/OnDemand window, select the

‘Disable OnDemand Streaming’ radio button and click the SUBMIT button. The screen returns to its

original form.

RF-Tuote Oy, Joensuunkatu 13, 24100 Salo, tel. +358-2736 6360, fa . +358-2-736 6360, info@rf-tuote.fi, www.rf-tuote.fi

4. Technical specification

8PSK/QPSK INPUT

Number of tuners 1* DVB-S, 3* DVB-S/S2

Input frequency range 950 - 2150 MHz

Input level -70 … -25 dBm

Waveform 8PSK, QPSK (SCPC, MCPC)

Symbol rate 4-40 MS/s

FEC decoder Automatic

CI slot 2 (option)

DATAHANDLING AND DE-MULTIPLEXING

Multi-protocol Encapsulation MPE

Encapsulation SPTS

Datagram and selection packing

Unicast/multicast filtering

Multicast address filters 128

Max output bit rate 40 Mbit/s

UDP/TCP/IP protocols

PSI/TCP private tables

LLC SNAP/ null encapsulation

LAN INTERFACE

Connector RJ45

Speed 10/100 autosensing

GENERAL

Power consumption 16VDC/1,1A

Dimensions 71mm*214mm*149mm

This symbol on the product or on its packing means that within the European Union the product must be

taken to separate collection at the product-end-of life.

Do not dispose of these products as unsorted municipal waste.

Fore more information about where you can drop off your waste equipment for recycling, please contact

your local city office, your house disposal service or the shop where you purchased the product.

RF-Tuote Oy, Joensuunkatu 13, 24100 Salo, tel. +358-2736 6360, fa . +358-2-736 6360, info@rf-tuote.fi, www.rf-tuote.fi

Andere RF TV-Tuner Handbücher

RF KV-87 Bedienungsanleitung

Beliebte TV-Tuner Handbücher anderer Marken

KWorld

KWorld PE310SE Bedienungsanleitung

COMPRO

COMPRO M505 - STARTUP Bedienungsanleitung

Genius

Genius TVGo DVB-T31 Bedienungsanleitung

Zinwell

Zinwell ZAT-332 Bedienungsanleitung

RGBlink

RGBlink TAO 1mini-HN Bedienungsanleitung

TViX

TViX PVR R-2200 Bedienungsanleitung

Xavix

Xavix Xavixport Bedienungsanleitung

Peak

Peak NET-TV Bedienungsanleitung

Fracarro

Fracarro SAF-HD 10 Bedienungsanleitung

Eonon

Eonon E0770 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-NOVA-T-Stick Bedienungsanleitung

Digital Devices

Digital Devices Octopus Net Bedienungsanleitung

Gericom

Gericom USB 2.0 DVB-T Tuner Bedienungsanleitung

ADS Technologies

ADS Technologies PTV-334 Bedienungsanleitung

Manta

Manta DVBT013T2 Bedienungsanleitung

Kenwood

Kenwood KTC-D500E Bedienungsanleitung

AVIWEST

AVIWEST DMNG PRO 100 Bedienungsanleitung

Abode

Abode IP Streaming Camera Bedienungsanleitung