RGBlink Driver 2A Bedienungsanleitung
Driver 2A User Manual 1
P
Driver 2A
User Manual
Manual #: RGB-RD-UM-SD E001
Revision: V1.0
Driver 2A User Manual 2
Driver 2A·User Manual
Thank you for choosing our products!
In order to allow you to learn how to use Driver 2A quickly, we bring you the
detailed user manual. You can read the introduction and directions before using
Driver 2A, please read all the information we provide carefully to use our
products correctly.
Copyright
©2015 All rights reserved by RGBlink.
This document is done by Xiamen RGBlink Science & Technology Co.,Ltd
independently. No part may be copied, reproduced or translated without
permission.
Notice
RGBlink provides this manual ―as is‖ without warranty of any kind, either
expressed or implied, including but not limited to the implied warranties or
merchantability and fitness for a particular purpose. RGBlink may make
improvements and/or changes to the product(s) and/or the program(s) described
in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors.
Changes are periodically made to the information in this publication; these
changes are incorporated in new editions of this publication.
Federal Communications Commission (FCC)
Statement
This equipment has been tested and found to comply with the limits for a classA
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area may cause
harmful interference, in which case the user will be responsible for correcting
any interference.
Driver 2A User Manual 3
Guarantee and Compensation
RGBlink provides a guarantee relating to perfect manufacturing as part of the
legally stipulated terms of guarantee. On receipt, the purchaser must
immediately inspect all delivered goods for damage incurred during transport,
as well as for material and manufacturing faults. RGBlink must be informed
immediately in writing of any complains.
The period of guarantee begins on the date of transfer of risks, in the case of
special systems and software on the date of commissioning, at latest 30 days
after the transfer of risks. In the event of justified notice of compliant, RGBlink can
repair the fault or provide a replacement at its own discretion within an
appropriate period. If this measure proves to be impossible or unsuccessful, the
purchaser can demand a reduction in the purchase price or cancellation of the
contract.All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of software as well
as to other service provided by RGBlink, being a component of the system or
independent service, will be deemed invalid provided the damage is not proven to
be attributed to the absence of properties guaranteed in writing or due to the
intent or gross negligence or part of RGBlink.
If the purchaser or a third party carries out modifications or repairs on goods
delivered by RGBlink, or if the goods are handled incorrectly, in particular if the
systems are commissioned operated incorrectly or if, after the transfer of risks,
the goods are subject to influences not agreed upon in the contract, all
guarantee claims of the purchaser will be rendered invalid. Not included in the
guarantee coverage are system failures which are attributed to programs or
special electronic circuitry provided by the purchaser, e.g. interfaces. Normal
wear as well as normal maintenance are not subject to the guarantee provided
by RGBlink either.
The environmental conditions as well as the servicing and maintenance
regulations specified in this manual must be complied with by the customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks,
registered trademarks or copyrights of their respective holders. All brand and
product names mentioned in this manual serve as comments or examples and
are not to be understood as advertising for the products or their manufactures.
Driver 2A User Manual 4
Company Address
Xiamen RGBlink Science & Technology Co., Ltd.
Headquarter: S603~604 Weiye Building Torch Hi-Tech Industrial
Development Zone Xiamen, Fujian Province, P.R.C
Shenzhen office: Floor 11, A1 Building, Baiwang R&D Building, Shahe
West Road, Xili Town, Nanshan District, Shenzhen, Guangdong Province,
P.R.C
Beijing office: No. 2702, Sino-Light Building Tower B, Wang-Jing East
Road, Chaoyang District, Beijing, P.R.C
Shanghai office: East Building F2, No. 88 Qinjiang Road, Shanghai,
P.R.C
Tel: +86-592-5771197
Fax: +86-592-5771202
Customer Hotline: 4008-592-315
Websites:
~http://www.rgblink.com
~http://www.rgblink.cn
E-mail: sales@rgblink.com
Driver 2A User Manual 5
Operators Safety Summary
The general safety information in this summary is for operating personnel.
Do Not Remove Covers or Panels
There are no user-serviceable parts within the unit. Removal of the top cover
will expose dangerous voltages. To avoid personal injury, do not remove the top
cover. Do not operate the unit without the cover installed.
Power Source
This product is intended to operate from a power source that will not apply more
than 230 volts rms between the supply conductors or between both supply
conductor and ground. A protective ground connection by way of grounding
conductor in the power cord is essential for safe operation.
Grounding the Product
This product is grounded through the grounding conductor of the power cord. To
avoid electrical shock, plug the power cord into a properly wired receptacle
before connecting to the product input or output terminals. A protective-ground
connection by way of the grounding conductor in the power cord is essential for
safe operation.
Use the Proper Power Cord
Use only the power cord and connector specified for your product. Use only a
power cord that is in good condition. Refer cord and connector changes to
qualified service personnel.
Use the Proper Fuse
To avoid fire hazard, use only the fuse having identical type, voltage rating, and
current rating characteristics. Refer fuse replacement to qualified service
personnel.
Do Not Operate in Explosive Atmospheres
To avoid explosion, do not operate this product in an explosive atmosphere.
Driver 2A User Manual 6
Terms In This Manual and Equipment
Marking
WARNING
Highlights an operating procedure, practice, condition, statement, etc,
which, if not strictly observed, could result in injury or death of
personnel.
Note
CAUTION
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
Highlights an essential operating procedure,
condition or statement.
Driver 2A User Manual 7
Change History
The table below lists the changes to the Driver 2A.
Format
Time
ECO#
Description
Principal
1.0
2014-01-16
0000
Release
Vira
Driver 2A User Manual 8
CONTENT
CONTENT ............................................................................................. 8
1. Introduction .................................................................................10
Chapter Structure.....................................................................................11
How to Use This Manual.........................................................................12
Terms and Definitions..............................................................................13
System Overview.....................................................................................19
Application Questions..............................................................................20
2. Hardware Orientation.................................................................21
In This Chapter............................................................................................21
Driver 2A Back Panel...............................................................................22
1: Audio Input.....................................................................................................22
2: DVI Input ........................................................................................................22
3: HDMI Input.....................................................................................................22
4,5, 6, 7: Gigabit Copper Port .........................................................................22
8,9: Power Interface and Switch.....................................................................22
Driver 2A Front Panel ..............................................................................23
1: Nixie Tube......................................................................................................23
2,3: Function Button..........................................................................................23
4,5: USB Control Port of Sending Card.........................................................23
6: LED Indicator.................................................................................................23
Driver 2A User Manual 9
3. Operation Manual.......................................................................24
In This Chapter.........................................................................................24
How to Connect........................................................................................25
How to Work.............................................................................................26
4. Hardware Installation.................................................................27
In This Chapter.........................................................................................27
Safety Precautions...................................................................................28
Unpacking and Inspection.......................................................................28
Site Preparation........................................................................................28
5. System Setup and Operations .................................................29
In This Chapter.........................................................................................29
How to Control the Brightness of Sending Card...................................30
6. Common Questions and Solutions .........................................31
In This Chapter.........................................................................................31
Nixie tube can not display brightness value..........................................32
No output on LED display .......................................................................32
A Specification................................................................................33
B Contact Information....................................................................34
Driver 2A User Manual 10
1. Introduction
This chapter is designed to introduce you to the Driver 2A User Manual. Areas to
be covered are:
Chapter Structure
How to Use This Manual
Terms and Definitions
System Overview
Application Questions
Andere Handbücher für Driver 2A
1
Inhaltsverzeichnis
Andere RGBlink Controller Handbücher
