RGMT SUPERAV AUTO 24H Bedienungsanleitung
AUTOMATIC WATCH
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
Vol. 1.23 EN DE
This timepiece is equipped with a
self-winding Mechanical Automatic
movement.
It does not need a battery.
It is powered by the motions of the
user’s own wrist during the wear of the
watch. You may also choose to wind the
watch manually.
SUPERAV AUTO 24H
24
12
420
816
23
DATE
MINUTE
HAND
SECOND
HAND
HOUR
HAND
SCREW
DOWN
CROWN
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
3
1
UNI-DIRECTIONAL
TURNING BEZEL
24 HOUR
HAND
BEFORE YOU USE THIS WATCH, IT IS
RECOMMENDED THAT YOU MANUALLY WIND
THE MAINSPRING TO START IT MOVING.
THIS WATCH IS AN AUTOMATIC WATCH EQUIPPED
WITH A MANUAL WINDING MECHANISM.
WINDING THE MAINSPRING
1. Unscrew the crown by turning it
anti-clockwise.
2. When it is in position [1], turn the
crown clockwise to wind. Wind
5-10 times and it will start to move
naturally after shaking slightly.
3. Push the crown in then screw it
securely.
0
1
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
0
1
2 3
* This watch MUST be worn for at least 8 (Eight)
hours each day to ensure it is fully wound. An
automatic watch will only wind when the watch
is on your wrist and your arm moves. Winding the
watch by the crown will put power on the spring
but not enough to allow the watch to function
fully. If your watch stops overnight or loses time
it means it is not being fully wound.
4
HOW TO SET THE TIME
1. Unscrew the crown and pull it out to position
[3]-(2nd click).
2. Turn the crown clockwise to set the correct time.
3. Push the crown in then screw it securely.
* Take a.m./p.m. into consideration when setting
the hour and minute hands to the desired time.
0
3
2
0
5
7
HOW TO SET THE DATE
1. Unscrew the crown and pull it out to position [2].
2. Turn the crown anti-clockwise to set the correct
date.
3. Push the crown in then screw it securely.
* Do not set the date between 9:00 P.M. and 4:00
A.M.
0
2
0
* Always be certain that your crown is SECURELY
SCREWED; this will prevent moisture from
entering in.
* The 24 hour hand moves correspondingly with the
hour hand.
* When setting the hour hand, check that the 24
hour hand is correctly set.
6
WATER RESISTANCE
The water resistance indicated on your timepiece serves
only as a guide. Actual water resistance may vary
depending on a number of important factors including
temperature, water salinity, and actual use under water.
The water resistance of your timepiece may eventually be
compromised over time with general wear and tear and
the use of your watch under adverse conditions.
Always remember to employ the screw down crown (if
available) to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should NEVER wear your watch in a jacuzzi,
hot shower or steam room where steam may enter the
case despite the watertight seals used to protect your
watch.
The steam may cause condensation inside your watch,
which may affect and damage the inner workings of your
watch – which would also not be covered by the warranty. 8
HOW TO USE A DEPLOYANT CLASP
1. Flip the cover.
2. Press the buttons on the clasp sides.
1
2
10
Nylon Head
Hammer
3.
4.
9
HOW TO RESIZE METAL BRACELET
On the inside of the bracelet, you will see some
small arrows engraved on removeable links.
1.
2.
11
5.
6.
12
Nylon Head
Hammer
FINISH
7.
8.
14
11.
FINISH
12.
9.
Micro size
adjustment
10.
13
IM.RGMT.CO
Weitere Einzelheiten zur Bedienung dieses Zeitmessers
finden Sie in der beiliegenden Broschüre oder unter:
AUTOMATISCHE UHR
Dieser Zeitmesser ist mit einem
mechanischen Automatikwerk mit
automatischem Aufzug ausgestattet. Er
benötigt keine Batterie. Es wird durch
die Bewegungen des eigenen Handgelenks
während des Tragens der Uhr automa-
tisch aufgezogen. Sie können sich auch
dafür entscheiden, die Uhr manuell
aufzuziehen.
SUPERAV AUTO 24H
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
Vol. 1.23 EN DE
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Sprachen:
Andere RGMT Betrachten Handbücher
RGMT
RGMT TORPEDO Bedienungsanleitung
RGMT
RGMT SURVEYOR Bedienungsanleitung
RGMT
RGMT TORPEDO Bedienungsanleitung
RGMT
RGMT NAVIGATOR Bedienungsanleitung
RGMT
RGMT T-1 AUTOMATIC Bedienungsanleitung
RGMT
RGMT DEMOLITION Bedienungsanleitung
RGMT
RGMT BATTLEDRESS Bedienungsanleitung
RGMT
RGMT FIELD MASTER Bedienungsanleitung
RGMT
RGMT BATTLEDRESS Bedienungsanleitung
RGMT
RGMT Locust Compass Bedienungsanleitung
RGMT
RGMT TRANS-CONTINENTAL Bedienungsanleitung
RGMT
RGMT ALTIMETER SKELETON Bedienungsanleitung
RGMT
RGMT ARTILLERY Bedienungsanleitung
RGMT
RGMT CONTINENTAL Bedienungsanleitung
RGMT
RGMT ARTILLERY Bedienungsanleitung
RGMT
RGMT ALTIMETER Bedienungsanleitung
RGMT
RGMT DEMOLITION Bedienungsanleitung
RGMT
RGMT SUPERAV X NSF Bedienungsanleitung
RGMT
RGMT FIELD MASTER Bedienungsanleitung
RGMT
RGMT BATTLEDRESS X NSF Bedienungsanleitung
