RHINO PelcoD 2400bps on RS485 Bedienungsanleitung



PTZSETUPGUIDE



For:

PelcoD2400bpsonRS485



PTZSETUPGUIDE

™©2008RhinoCoTechnologyPty.Ltd.

9HannabusPlace,McGrathsHill,NSWAustralia2756

http://www.rhinosecruity.com

Introduction

The purpose of this guide is assist in the installation, setup and use of any PTZ with any PTZ

Keyboard or compatible DVR. We recommend using only RS485 with PelcoD on 2400Bps upto 16

IDs, as this is the most common and universal format. If you cannot run a 2400Bps baudrate then we

recommend using 4800Bps, in which case you will have to consult you user manual for more

assistance.

All PTZ systems have a means of communication, this is usually RS232 or RS485. RS485 is more

commonly used as it can be run on only 2 wires and over greater distances. Some situations may

require an RS485 Repeater which can extend the distance even further. For any DVRs or PCs that

ony support RS232, an RS232 to RS485 converter may be required.

Every PTZ device runs on a protocol which is a language of communication with other PTZ devices.

For the purpose of this guide we will use only the PelcoD protocol which is used by all manufactures.

For more detailed information on any product you may need to consult the manufactures own manual.

Contents

1. PTZs:

VSPTZ55(W) Page 1.

VSSAM-SPD3300 Page 2.

VSJVC-TKC686(WP)E Page 3.

VSPTZ7722B Page 4.

2. Keyboards:

VSPTZKB Page 5.

VSSAM-SCC3100A Page 6.

3. DVRs:

DVRPLATINUM Page 7.

DVRDIAMOND Page 8.

DVRWGUARD Page 9.

DVRAPEX Page 10.

Securview VSPTZ55(W) PTZ on ID01 and Pelco-D at 2400Bps

For Power Connection:

24vAC+ Red

24vAC- Black

For 2 wire RS485 Connection:

RS485+ Orange (Rx+)

RS485- Yellow (Rx-)

ID Setting Switch

1 2 3 4 5 6 7 8 9 10

ÏÐÐÐÐÐÐÐÐÐ

Protocol Setting

1 2 3 4 5

ÐÐÏÐÐ

Samsung SPD-3300 PTZ on ID01 and Pelco-D at 2400Bps

For Power Connection:

24vAC+

24vAC-

For 2 wire RS485 connection:

RS485+

RS485-

PTZ ID

SW1 – 0

SW2 – 1

SW3 – 2

JVC TK-C686WPE PTZ on ID01 and Pelco-D at 2400Bps

For Power Connection:

24vAC+ Red

24vAC- Black

For 2 wire RS485 connection:

RS485+ Orange/White (Rx+)

RS485- Black/White (Rx-)

Setting Switch

1 2 3 4 5 6 7 8

ÏÐÐÐÐÐÐÐ

Machine ID

1 2 3 4 5 6 7 8

ÏÐÐÐÐÐÐÐ

Option Switch

1 2 3 4 5 6 7 8

ÐÐÐÐÐÏÐÐ

To access to onboard menu:

Press PRESET > 9 > 5 > ENTER

MENU = Close

SET = Open

Securview VSPTZ7722B PTZ on ID01 and Pelco-D at 2400Bps

For Power Connection:

24vAC

Ground

24vAC

-OR-

12vDC Socket

For 2 wire RS485 Connection:

RS485+ (Rx+)

RS485- (Rx-)

ID Setting Switch

1 2 3 4 5 6 7 8

ÏÐÐÐÐÐÐÐ

Simplex/Duplex Setting

1 2

ÐÐ

S2 Setting

1 2 3 4

ÐÐÐÐ

S1 Setting

1 2 3 4

ÏÐÐÐ

Securview VSPTZKB on ID01 and Pelco-D at 2400Bps

For Power Connection:

12vDC Socket

For 2 wire RS485 connection:

RS485+ (Tx+)

RS485- (Tx-)

There are 2 sets are Tx- and Tx+, either can be used.

Protocol Switch

1 2 3 4 5 6 7 8

ÐÏÏÏÏÏÏÏ

Samsung VSSAM-SCC3100A on ID01 and Pelco-D at 4800Bps

Note: The Samsung VSSAM-SCC1300A does not support a baudrate of 2400bps, and it is

therefore necessary to run any PTZ cameras on 4800bps or above.

For Power Connection:

12vDC+

12vDC-

For 2 wire RS485 connection:

Press ‘PTZ’ to enter PTZ mode. Press ‘MENU’ to enter setup, then press ‘1’ to enter ‘PTZ SETUP 1’.

Press ‘>>’ to enter ‘PTZ SETUP 2’ and then press ‘1’ to choose the model. You can then type ‘01’ on the

keypad to enter ID01 and press the ‘+/-‘ buttons to select ‘PELCO-D’ as the protocol.

Securview DVRPLATINUM on ID01 and Pelco-D at 2400Bps

For 2 wire RS485 connection on rear of DVR with additional cable:

RS485+ Red (Tx+)

RS485- White (Tx-)

Set the DVR to use the inbuilt RS485 by going to ‘Config’ > ‘System’ > ‘Serial’, and setting the Odcap to

PTZ.

Set the PTZ connection up by going to ‘Config’ > ‘PTZ’, and setting ‘Camera #’ to ‘PELCO D (2400)’

and ‘Protocol_#01’. You should also make sure that the Serial Port is set to ‘Odcap’.

Once this has been done and your PTZ is connected, you can then access the PTZ control panel by

clicking the blue arrow on the right hand side. This will give you the controls to Pan, Tilt, Zoom, and

Focus your PTZ.

Inhaltsverzeichnis

Andere RHINO Sicherheitssystem Handbücher

RHINO

RHINO ADVANCED PANIC PACK Bedienungsanleitung

RHINO

RHINO RCA Bedienungsanleitung

RHINO

RHINO 832 Bedienungsanleitung

RHINO

RHINO 232 Bedienungsanleitung

RHINO

RHINO RCA-2 Bedienungsanleitung

RHINO

RHINO RA96 Bedienungsanleitung

RHINO

RHINO Watchguard Digital V2 Bedienungsanleitung

RHINO

RHINO Watchguard Digital V2 Bedienungsanleitung

RHINO

RHINO RA97 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung