Rice Lake IDIMENSION 20 Bedienungsanleitung

iDimension 100

Workstation

Assembly Instructions

PN 171899

Contents i

Contents

1.0 Introduction..................................................................................................................................... 1

1.1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.2 iDimension 100 Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.0 Assembly......................................................................................................................................... 3

2.1 Pole Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.2 Head Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.3 Display Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.3.1 Install Scale (Optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.0 Setup ............................................................................................................................................... 9

3.1 Advanced configuration with QubeVu Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

3.1.1 Define QubeVu on your Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Technical training seminars are available through Rice Lake Weighing Systems.

Course descriptions and dates can be viewed at www.ricelake.com/training

or obtained by calling 715-234-9171 and asking for the training department.

Specifications subject to change without notice.

Rice Lake Weighing Systems is an ISO 9001 registered company.

September 21, 2015

ii iDimension 100 Assembly Manual

Rice Lake continually offers web-based video training on a growing selection

of product-related topics at no cost. Visit www.ricelake.com/webinars.

Introduction 1

1.0 Introduction

This document describes how to assemble the iDimension 100.

Manuals can be viewed or downloaded on the Rice Lake Weighing Systems distributor site at

www.ricelake.com

Warranty information can be found on the website at www.ricelake.com/warranties

1.1 Sa f ety

Safety Symbol Definitions

Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death, and

includes hazards that are exposed when guards are removed.

Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury.

Indicates information about procedures that, if not observed, could result in damage to equipment or

corruption to and loss of data.

Safety Precautions

Do not operate or work on this equipment unless you have read and understand the instructions and

warnings in this manual. Contact any Rice Lake Weighing Systems dealer for replacement manuals.

Proper care is your responsibility.

General Safety

Failure to heed may result in serious injury or death.

Electric shock hazard!

• Pluggable equipment must be installed near an easily accessible socket outlet.

• Always disconnect from main power before performing any work on the device.

• Check the power cable for damage regularly and replace it immediately if it is damaged.

• On the side of the device, maintain a clearance of at least 1.5 inches in order to prevent damage to the cable.

Do not allow minors (children) or inexperienced persons to operate this unit.

Do not operate without all shields and guards in place.

Do not place fingers into slots or possible pinch points.

Do not use this product if any of the components are cracked.

Do not make alterations or modifications to the unit.

Do not remove or obscure warning labels.

Keep hands, feet and loose clothing away from moving parts.

Do not use in hazardous areas.

Do not open the scanning head. The warranty and certification is void if this stipulation is ignored. The device may only be

opened by authorized persons.

WARNING

CAUTION

Important

WARNING

2iDimension 100 Assembly Instructions

1.2 iDimension 100 Parts

Figure 1-1. Parts Illustration

Immediately after unpacking the iDimension 100, visually inspect the contents to ensure all components are

included and undamaged. If any parts were damaged in shipment, notify the shipper immediately.

Failure to adhere to the notes below will invalidate the warranty and may result in damage that could

require repair or replacement charges.

• Retain packaging. When transporting the unit, always disassemble and pack it in its original packaging.

• Use only supplied power adaptor. Never short-circuit the power adaptor or the device.

•Keeptheunitdry.

• Operate between 41 - 104º F (5 - 40º C).

• Never remove the iDimension 100’s head cover or the electrical connection panels at the base of the pole assembly.

• Never modify or attempt to repair the unit. Service must be performed only by Rice Lake Weighing Systems.

• Handle cables and cable connectors with care. Never use damaged power cords or plugs or loose electrical sockets.

Never touch the power cord with wet hands.

• Ensure that the base plate, pole assembly and head unit are all securely attached before attempting to move the unit.

• Never lift the unit by grasping only the pole assembly; always ensure that both sections of the pole assembly and the

base plate are supported.

• Never drop or allow an impact to the head.

• Mount on a flat surface.

• Never use product for anything other than its intended purpose.

Power Cord

Pole Base

Hex Wrenches

Ethernet Cable

Display

Head

Calibration Box

Important

Assembly 3

2.0 Assembly

2.1 Pole Assembly

Figure 2-1. Remove Screws

1. Using the appropriate hex wrench, remove the two screws at the pole joint. Retain the screws for assembly.

Leave the other two screws in place.

2. Lay the pole out on a hard surface covered with a rug or similar soft covering.

3. Ensure that the poles are aligned correctly using the notch and pin as a guide.

4. Insert the lower half of the pole into the upper half.

Figure 2-2. Pole Assembly

5. Reinsert and tighten the screws removed in step 1.

6. Lay the pole assembly on a table or other stable surface. Ensure the power block is hanging over the edge.

Figure 2-3. Remove Power Block Screws

7. Remove the four screws that are in the bottom of the power block.

8. Insert the two pins on the base into the matching holes of the power block.

9. Reinsert and tighten the four bolts removed in step 7.

Screws to be removed

Alignment Point

Screws to be left

in place

Note

Pole Intersection

Retained Screws

Alignment Point

4iDimension 100 Assembly Instructions

Figure 2-4. Pole Assembly

10. Stand the assembled pole upright.

2.2 Head Attachment

Figure 2-5. Remove Cable Shroud Cover

1. Loosen the four screws that secure the cable shroud cover. Do not remove them.

2. Slide the shroud cover back and lift it off.

3. Align the head with the cable shroud at the top of the pole.

Figure 2-6. Align Head with Shroud

4. Connect the cables. See Figure 2-7.

Cable Shroud

Display Cable

Power Block

Base

Screws

Slide direction

Assembly 5

Figure 2-7. Cable Connections

Figure 2-8. Connected Cables

5. Push the cables into the cable shroud carefully.

6. Insert the screws on the head into the keyhole slots on the shroud. Do not tighten them yet.

Cable Order Cable Label Port Label

1 Ethernet Ethernet

2 USB 3 USB 3

3 USB 2 USB 2

4 Auxiliary power only Power only 1

5 24 VDC in Input: 24v

Table 2-1. Cable Connections

The cables and ports on back of the head are

labeled for easy connections.

Note

Keyhole

Slots

6iDimension 100 Assembly Instructions

Figure 2-9. Reinstall Shroud Cover

7. Place the shroud cover in the cable shroud and slide it forward until it clicks into place.

8. Re-tighten the fours screws that secure it.

Figure 2-10. Tighten Head Screws

9. Tighten the bolts that attach the head to the shroud.

2.3 Display Assembly

Figure 2-11. U-Shaped Display Bracket

1. Loosen the bolt that holds the u-shaped display bracket.

Shroud Cover

U-Shaped

Bracket

Inhaltsverzeichnis

Andere Rice Lake Dokumentenkamera Handbücher

Rice Lake

Rice Lake IDIMENSION 200 Bedienungsanleitung

Beliebte Dokumentenkamera Handbücher anderer Marken

AVer

AVer AVerVision F35 Bedienungsanleitung

Lumens

Lumens PS760 Bedienungsanleitung

Genee World

Genee World GV8100 Bedienungsanleitung

Touchboards

Touchboards Vidifox DV 480 Bedienungsanleitung

Dukane

Dukane 210 Bedienungsanleitung

TTS

TTS Easi-View Pro Bedienungsanleitung

Lumens

Lumens dc153 Bedienungsanleitung

Avermedia

Avermedia AVerVision SPB350 Bedienungsanleitung

AVer

AVer TR311V2 Bedienungsanleitung

Inswan

Inswan INS-3 Bedienungsanleitung

Genee

Genee Vision 6100 Bedienungsanleitung

Rolls

Rolls DB14 - 02/10 Bedienungsanleitung

Lumens

Lumens DC-W80 Bedienungsanleitung

AVer

AVer AVerVision SPB350+ Bedienungsanleitung

Dukane

Dukane FASTFAX AV-P750U Bedienungsanleitung

Optoma

Optoma DC554 Bedienungsanleitung

Ipevo

Ipevo Ziggi Bedienungsanleitung

Vidifox

Vidifox PV 380 Bedienungsanleitung