Rice Lake LaserLight3 Bedienungsanleitung
September 30, 2022 PN 215476 Rev A
LaserLight3™ Remote Display
Quick Start Guide
This document describes how to set up the LaserLight3 to operate as a remote display.
Manuals and additional resources are available from the Rice Lake Weighing Systems website at www.ricelake.com
Warranty information can be found on the website at www.ricelake.com/warranties
NOTE: For more information about LaserLight3, see LaserLight3 Remote Display Technical Manual (PN 214748).
Preliminary Tasks
• Unpack and visually inspect the LaserLight3 for damage. If parts were damaged in shipment, notify Rice Lake Weighing
Systems and the shipper immediately.
• Mount LaserLight3 with included mounting bracket.
Cable Connection
Connect data communication from an indicator to the CPU board..
NOTE: If using factory installed Wi-Fi communication, see addendum PN 214366 for configuration.
WARNING: The LaserLight3 has no on/off switch. Before opening the unit, ensure the power cord is disconnected from the
power outlet.
Use a ground wrist strap to protect components from electrostatic discharge (ESD) when working inside the enclosure.
1. Unplug LaserLight3 from power source.
2. Loosen captive thumbscrews then open enclosure front door.
3. Route communication cable from indicator through LaserLight3 cord grip into the enclosure.
4. Connect cable to one of the following communication ports RS-232 (J3), RS-482/422 (J4), Ethernet (J8) or 20 mA
(J11), while adhering to port pin assignment (Figure 1). Coordinate software settings with the installed wiring.
NOTE:
The LaserLight3 parts kit includes four, five and six pin connectors to facilitate connection with the CPU board ports.
Figure 1. CPU Board Informational Label (PN 212330)
LaserLight3 Remote Display Quick Start Guide
2 Visit our website www.RiceLake.com
Software Configuration
Access Setup Mode
Press Menu to access the setup menu in setup mode and configure the LaserLight 3. If Setup mode is inaccessible by pressing
the Menu Button, perform the following:
1. Plug in LaserLight3 and allow to power on and initialize.
2. Open front door using captive thumbscrews.
3. Perform one of the following to enter Setup mode:
• Short setup jumper pins (J25) on CPU board
• Install shunt on audit jumper
(J24) pins 2 and 3 on CPU board (enables Audit Trail mode and allows Setup access
from Menu) and then press the Menu button
4. Close front door and secure with captive thumbscrews.
Figure 2. Setup Mode Jumper
Configure Display Type
The Type parameter in the Dsplay (Display) menu has three options to set the information that appears on the display. Set the
Type parameter as:
• Legacy (annunciators along the bottom)
• Standard (annunciators along the right side)
Figure 3. Menu Path for Type Parameter
CPU Board
Jumper Function Application
J24 Audit Trail Off Install shunt on pins 1 and 2
Audit Trail On Install shunt on pins 2 and 3
J25 Setup Short pins 1 and 2 momentarily
Setup Jumper
(J25)
Audit Jumper
(J24) with
Shunt
Dsplay
K
bd
L
ock
Setup Mac ID
Version
Program SFormtFormat
Bright Type
Contact
Legacy Standard
LaserLight3 Remote Display Quick Start Guide
© Rice Lake Weighing Systems ● All Rights Reserved 3
Automatic Baud Configuration
The Auto (Automatic) baud configuration cycles through serial communication protocol (RS-232, RS-485/422 and 20 mA) baud
settings (baud rate, bits and stop bits) until it establishes a serial connection.
Set the Auto setting for the Baud parameter of the communication protocol used.
Figure 4. Menu Path for Baud Parameter
Auto-Learn and Data String Recognition
Auto-Learn examines the data stream sent from the connected indicator and determines the data settings and format used by
the indicator. Auto-Learn is capable of recognizing several common data string formats used in the weighing industry. If
enabled, LaserLight3 attempts to learn the incoming data steam when it is powered on, when the data stream starts or when
the data stream is paused and restarted.
Set the used communication protocol (RS-232, RS-485/422, 20 mA, Ethernet or Wi-Fi) Trigger parameter as RmtIn (Remote In)
to enable Auto-Learn.
NOTE: It is suggested to only configure one communication protocol as Remote In. If more than one communication
protocol is configured as Remote In, LaserLight3 uses the first configured communication protocol that occurs in the
system menu. For example, if RS232-2 and 20mA were set as Remote In, RS232-2 would be used as it occurs before 20MA
in the system menu.
RS232 1 RS32 2 RS485
20
M
A
Serial USBWiFi
CommRemote Format
20MA
4800 9600 19200
28800
57600 115200 Auto
Trigger Baud
38400
Setup Mac IDVersion
1200 2400
230 W. Coleman St. • Rice Lake, WI 54868 • USA
U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe +31 (0)26 472 1319
© Rice Lake Weighing Systems Specifications subject to change without notice.
www.ricelake.com
PN 215476 Rev A
September 30, 2022
LaserLight3 Remote Display Quick Start Guide
Figure 5. Menu Paths for Remote In Parameters
NOTE: If the text NODATA appears, verify connection from the indicator to LaserLight3.
If data does not display, ensure data stream is set to transmit from indicator.
Auto-Learn mode may be bypassed by using Manual mode.
If OvrRng (Over Range) displays after the Auto-Learn process parses data, then the weighment value sent is beyond the
capabilities of the display (six characters). Manual mode can frequently resolve character quantity issues.
If the LaserLight3 does not match a data format, it automatically attempts to parse the weight, units, mode, status and
weight data out of frame. If a valid weight is not found, manual mode must be used to configure LaserLight3.
For more information about Manual mode see LaserLight3 Remote Display Technical Manual (PN 214748).
Serial USB Ethrnet
W
i
F
i
Setup Mac IDVersion
CommRemote Format
RS232 1 RS32 2 RS485
20MA
Mac ID DHCP Enabled Ip Addr
Gateway EthSrvr EthClnt
Subnet
Trigger
Command StrInd StrLft RmtIn
Command StrInd StrLft RmtIn
Port Echo
Name
Trigger
Eoldly
IPAddre
LnTerm
Port
Respons
Trigger
Andere Handbücher für LaserLight3
5
Inhaltsverzeichnis
Andere Rice Lake Monitor Handbücher
Rice Lake
Rice Lake LaserLT-60 Bedienungsanleitung
Rice Lake
Rice Lake EL232 XPCD Bedienungsanleitung
Rice Lake
Rice Lake LaserLT-60 Bedienungsanleitung
Rice Lake
Rice Lake LaserLight3 Bedienungsanleitung
Rice Lake
Rice Lake 1280 Enterprise Series Installationshandbuch
Rice Lake
Rice Lake LaserLight Series Bedienungsanleitung
Rice Lake
Rice Lake MSI-8000 Bedienungsanleitung
Rice Lake
Rice Lake LaserLight3 Bedienungsanleitung
Rice Lake
Rice Lake MSI-8000HD Bedienungsanleitung
Rice Lake
Rice Lake LaserLight2 ConnexLink 167091 Bedienungsanleitung
Rice Lake
Rice Lake RD-300 Bedienungsanleitung
Rice Lake
Rice Lake IQ plus 710 Bedienungsanleitung
Rice Lake
Rice Lake CLS-680 Bedienungsanleitung
Rice Lake
Rice Lake SURVIVOR IQ F Series Bedienungsanleitung
Rice Lake
Rice Lake LaserLight Bedienungsanleitung
Rice Lake
Rice Lake SURVIVOR IQ L Series Bedienungsanleitung
