Rice Lake CLS Series Bedienungsanleitung

Cargo Lift Scale Series

Wired to Wireless Conversion Instructions

Manuals can be viewed or downloaded from the Rice Lake Weighing Systems website at www.ricelake.com/manuals

The CLS Series Cargo Lift Scale has the capability to go from wired to wireless operation with a few steps. The wireless option

attaches onto the back of the indicator and collects data from the junction box without the use of a coiled wire cable.

The conversion kit contains the following items:

• Angle/battery box assembly (PN 167282)

• Wireless sub-assembly box (PN 98289)

• Lithium-Ion battery (PN 96343)

• Lithium-Ion battery charger (PN 96344)

Wireless communication between the indicator and the junction box which is located on the forklift and is powered by a

lithium-ion battery housed in a battery box.

Figure 1. Wireless Components for Communication

To convert the unit from wired to wireless:

1. Remove the angle bracket and the wired cable connecting the indicator to the forklift scale.

2. Install and wire from the wireless sub-assembly box to the indicator.

3. Install the angle/battery box assembly to the top of the carriage.

Remove Wired Cable

To remove the wired cable from the forklift to the indicator:

1. Cut cable ties that are securing the coiled wire between the bottom of the scale and the top of the mast of the forklift.

2. Disconnect the cable from the indicator.

3. Remove top cover plate from the forklift to access the junction box located beneath.

4. Disconnect the wired cabling from the junction box.

PN 101112 Rev B

May 14, 2019

CLS Series Wired to Wireless Conversion Instructions

2 Visit our website www.RiceLake.com

Install and Wire the Wireless Sub-Assembly Box to Indicator

To install the wireless sub-assembly box to the indicator:

1. Use the attached screws and screw the wireless sub-assembly box onto the back of the indicator.

2. Open the rear of the indicator.

3. Run the wire through bottom cord grip of indicator and wire into the connections.

Figure 2. Indicator

Attach the wireless

sub-assembly on to the

rear of the indicator.

CLS Series Wired to Wireless Conversion Instructions

CLS-420 Wiring Diagrams

Figure 3. CLS-420 Indicator Wiring Diagram

Red

Black

Blue

White

Green

CLS Series Wired to Wireless Conversion Instructions

4 Visit our website www.RiceLake.com

Installing the Angle Cover Plate and Battery Box Assembly

To install the angle cover plate and battery box assembly:

1. Attach pigtail from angle cover plate and battery box assembly to junction box.

2. Secure angle cover plate and battery box assembly to top of carriage.

3. Install battery.

4. Following for battery option.

Figure 4. Battery Box

Wireless Battery Option

Wireless technology eliminates the need for the coiled interface cable. The reinforced battery box is welded onto the cover

plate. There is an On/Off switch to conserve the life of the battery and an LED to indicate when the battery is on. Battery life is

approximately 24 hours of continuous use, with only eight hours to fully charge.

The wireless technology operates using a paired set of IEEE 802.15.4 wireless modules. It operates in unlicensed bands

including 2.4 GHz, 900MHz and 868 MHz. One module is in the battery angle bracket assembly, the other is in the wireless

junction box connected to the indicator.

If multiple units are being installed, make a note of the original components supplied on each pallet. They will only operate in

combination with each other.

Figure 5. Wireless Battery Option

LED indicates On/Off

Antenna

On/Off Switch

CLS Series Wired to Wireless Conversion Instructions

Battery Removal and Installation

To replace the lithium-ion battery that powers the unit:

1. Place the On/Off switch in the Off position.

2. Release latches and raise the cover.

3. Grasp a tab on the end of the battery and pull up.

4. Insert a new/charged battery into the battery case.

5. Close the cover and engage the latches.

Figure 6. Battery Removal and Installation

The CLS scale uses a supplied lithium-ion battery to supply power to the indicator when using a wireless version of the CLS-

420. The lithium-ion battery is located on the top of the cover plate in a painted enclosure.

Charging the Lithium-Ion Battery

The lithium-ion battery comes with a two-bay, level-3 stand alone smart battery charger, a DC power jack and AC power cord.

The average charge time for the battery is eight hours each.

Figure 7. Two-Bay Battery Charger and Parts for the Lithium-Ion Battery

Part No. Description

96343 Lithium-Ion Battery

96344 2-Bay Battery Charger

96345 10-Bay Battery Charger

Table 1. Battery Replacement Parts

Battery Removal Tab

Battery

On/Off Switch

Latches

To calibrate the battery

pack, press the button on

front label.

230 W. Coleman St. • Rice Lake, WI 54868 • USA

U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe +31 (0)26 472 1319

Rice Lake Weighing Systems is an ISO 9001 registered company.

www.ricelake.com

PN 101112 Rev B

May 14, 2019

Use the following steps to charge the battery prior to use:

1. Insert the plug end of the power cable into the DC power jack on the battery charger and the AC plug into an outlet.

2. Insert battery into the bay.

3. There is one LED indicator in front of each bay which will illuminate to indicate the status of the battery as follows:

Calibrating the Lithium-Ion Battery

To keep the battery fuel gauge as accurate as possible, it is necessary to run the pack through a recalibration cycle on a

monthly basis. To recalibrate, place the battery in the left bay of the charger and press the button on the front label,

See Figure 7 on page 5. This initiates the recalibration sequence in the left bay only. The process can take up to nine hours to

complete and a recommended recalibration must be done once a month to keep the battery accurate.

Lithium-Ion Battery Specifications

Signal Description

Off No Battery

Green Flashing Fast Charging

Green Solid Fully Charged

Yellow Flashing Recalibrating

Yellow/Green Alternating Recalibrating

Yellow Solid Standby

Red Flashing Error

Table 2. Battery Charging LED Signals

Nominal Capacity 6600 mAh

Nominal Voltage 11.1 V

Charging Method Constant Current

Constant Voltage

Charging Voltage 12.6 V

Charging Current 4.0 A

Charging Time 100% at 8 hours

Ambient Temperature Charge 0º±40ºC (32º-104ºF)

Discharge -20º±60ºC (-4º-140ºF)

Storage -20º±50ºC (-4º-122ºF)

Weight (Maximum) 430 g

Dimensions (Maximum) Depth 22.80 mm

Length 214.0 mm

Volumetric Energy Density 466 Wh/I

Gravimetric Energy Density 167 Wh/kg

Maximum Hours of Charge 24 hours

Nominal Capacity 6600 mAh

Table 3. Battery Specifications

Andere Handbücher für CLS Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rice Lake Skala Handbücher

Rice Lake

Rice Lake RL-TA Series Bedienungsanleitung

Rice Lake

Rice Lake INT300 Bedienungsanleitung

Rice Lake

Rice Lake 102613 Montageanleitung

Rice Lake

Rice Lake Farm Bars Bedienungsanleitung

Rice Lake

Rice Lake 181881 Bedienungsanleitung

Rice Lake

Rice Lake Load Ranger Bedienungsanleitung

Rice Lake

Rice Lake RoughDeck SS Bedienungsanleitung

Rice Lake

Rice Lake RL-DBS Betriebsanleitung

Rice Lake

Rice Lake 250-10-4 Series Bedienungsanleitung

Rice Lake

Rice Lake RS-130 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

Rice Lake

Rice Lake TC-220 Bedienungsanleitung

Rice Lake

Rice Lake Versa-portion RLP-S Bedienungsanleitung

Rice Lake

Rice Lake iDimension PWD Benutzerhandbuch

Rice Lake

Rice Lake 140-10-7N Series Bedienungsanleitung

Rice Lake

Rice Lake DIGI DC-300 Series Bedienungsanleitung

Rice Lake

Rice Lake DIGI DC-782 Bedienungsanleitung

Rice Lake

Rice Lake CLS-680 Bedienungsanleitung

Rice Lake

Rice Lake BCi Programmierhandbuch

Rice Lake

Rice Lake IQ6200 Bedienungsanleitung

Rice Lake

Rice Lake RL1200 Bedienungsanleitung

Rice Lake

Rice Lake BenchMark MS Bedienungsanleitung

Rice Lake

Rice Lake RL-MPS-40 Bedienungsanleitung

Rice Lake

Rice Lake RL-MCS Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung

Fidelity Electronics

Fidelity Electronics G2e Bedienungsanleitung