Rice Lake Load Ranger Bedienungsanleitung

Load Ranger Wheel Weigh Pads

Quick Start Guide

This document provides the procedures necessary to quickly setup the Load Ranger Wheel Weigh Pads and pair them with the

Ai-1 Indicator to take weight readings.

Wheel Weigh Pad Configuration

Figure 1. Wheel Weigh Pad Display

1. Press to power on the indicator then press during startup.  displays.

2. Press three times.  displays.

3. Press to enter the Serial menu.  displays.

4. Press to enter the ID settings.

5. Press or to increase or decrease the selected digit and press to move between the digits to enter the

pad ID number.

The first Pad ID number must be 01 and the remaining pad ID numbers must increment in ascending numeric order.

Example: 01, 02, 03, etc.

6. Press to confirm.  displays.

7. Press to enter the Bluetooth Initialization menu.  displays.

8. Press to confirm.  displays followed by . displays.

9. Press twice.  displays.

10. Press to confirm.  briefly displays and all the changed parameters are saved.

11. Repeat steps for all wheel weigh pads in the system.

MODE

SET

DIAG

NUM

SET

NUM

DATA

Note

PN 189611 Rev B

February 22, 2021

Load Ranger Wheel Weigh Pads

2 Visit our website www.RiceLake.com

Pairing Ai-1 Indicator with Wheel Weigh Pads

1. Press to turn on the Ai-1 indicator.

2. During startup, press the upper right corner of the screen when the logo displays to enter the Technical Setup menu.

Figure 2. Touch Upper Right Corner of the Display

3. Press .

4. Press .

5. Press .

Figure 3. Select Scales

6. Select the number of wheel weigh pads to be used.

7. Press .

8. Press .

9. Press .

Calibration

Scale selection

1 scale/s

Number of scales

Number of scales 1/3

Cancel OK

WWS configuration

WWS pairing

Load Ranger Wheel Weigh Pads

10. Press to start pairing process. A prompt displays (Figure 4). Do not press anything at this time.

Figure 4. Start Pairing

11. Turn off all of the wheel weigh pads.

12. Turn on the first weigh pad only (pad assigned ID 01).

13. Press in the prompt window (Figure 4 on page 3) to start the pairing process. Connecting... displays

alongside the ID number.

14. Once the serial number of the first wheel weigh pad displays, turn on the second wheel weigh pad (assigned ID 02).

Figure 5. Pairing

15. Repeat this process until all of the weigh pad pin numbers in the desired system are displayed. Once the last wheel

weigh pad is paired, a prompt displays.

Figure 6. Pairing Successful

16. Press to confirm the completion of pairing. The Gravity Value Setting keyboard displays.

PAIR

Start pairing?

Please turn on WWS one by one.

WWS pairing

No Yes

Yes

WWS paring

100625534

Connecting...

Esc

Pairing terminated successfully.

Receive configuration from

paired WWS?

WWS pairing

No Yes

Yes

Load Ranger Wheel Weigh Pads

4 Visit our website www.RiceLake.com

17. This should save loading weights on all eight scales.

Figure 7. Set Gravity Value

18. Enter the gravity value for the area the wheel weigh pads are to be used in.

19. Press .

20. Press three times to get back to the Technical Setup menu.

Figure 8. Technical Setup Menu

21. Press . Setup changed box displays.

Figure 9. Setup Changed

22. Press to save settings and complete setup. Indicator reboots to Weigh mode.

Initial Setup Parameters

The following parameter windows display during initial setup before the indicator reboots to Weigh mode.

• The Backup of the Configuration window — Press to backup all settings

• The Password window displays — Press or , depending if a password is needed

• The Technical Setup window displays — Press to convert the indicator units to match the weigh pad units

Gravity value setting

1Esc2

4 5

7BkSp8 -9

COK0

9.75001 ~9.84999

9.8O39O

Esc

Calibration

First Programming

AF08 functions

Generic functions

Shortcuts

Databases

Technical setup (INTERNAL USE ONLY)

1/3

Esc

Setup changed.

Save changes before restart the

indicator?

Technical setup

Cancel YesNo

Yes

Load Ranger Wheel Weigh Pads

Applications

The Load Ranger weigh pads can be arranged to serve multiple applications. The adjustment from one scenario to another is

made quickly and easily with the wireless and portability features of the Load Ranger system. This section highlights several of

the arrangements available.

For additional Load Ranger Wheel Weigh Pad System information, see the Load Ranger Wheel Weigh Pad System

Technical Manual (PN 189612).

Wireless Setup

A wireless system allows for weighing with up to seven connected wheel weigh pads.

Connection Procedure

1. Assign ID numbers to the weigh pads and initialize Bluetooth.

2. Pair the Ai-1 indicator with the weigh pads.

3. Turn off the weigh pads and the Ai-1 indicator.

4. Connect RS485 cables to the weigh pads data communication ports.

5. Connect the other ends of each RS485 cable to one of the Ai-1 indicator communication ports.

The wheel weigh pads can be connected to any of the RS485 ports on the Ai-1 indicator. The pad ID assigned within

the weigh pad dictates the scale number and it does not need to match the Ai-1 indicator channel number.

6. Turn on all of the weigh pads.

7. Turn on the Ai-1 indicator.  briefly displays on weigh pads (  represents the assigned pad ID number).





 then displays on the weigh pads and they are ready for use.

Wired Setup

A wired system allows for weighing up to four connected wheel weigh pads.

The data communication port is located on the underside of the wheel weigh pad. For the RF-MD the port is located at the

handle end of the platform and is the port further from the edge. For the RF-WD and RF-XWD the port is located at the end

opposite of the platform handles.

Hybrid Wireless Setup

A hybrid system allows for weighing up to 14 connected wheel weigh pads.

A hybrid wireless system allows for the weighing of vehicles with four to seven axles. These larger applications are possible by

connecting each axle set of weigh pads together with a cable, so that one weigh pad is able to transfer both sets of weigh data

wirelessly to the indicator.

Seven wireless and seven wired wheel weigh pads can be connected together for a total of 14 wheel weigh pads.

Note

230 W. Coleman St. • Rice Lake, WI 54868 • USA

U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe +31 (0)26 472 1319

Rice Lake Weighing Systems is an ISO 9001 registered company.

www.ricelake.com

Load Ranger Wheel Weigh Pads

PN 189611 Rev B

February 22, 2021

Inhaltsverzeichnis

Andere Rice Lake Skala Handbücher

Rice Lake

Rice Lake RS-130 Bedienungsanleitung

Rice Lake

Rice Lake RoughDeck LP Bedienungsanleitung

Rice Lake

Rice Lake RL101 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260B Bedienungsanleitung

Rice Lake

Rice Lake CW-90B Bedienungsanleitung

Rice Lake

Rice Lake QB Series Bedienungsanleitung

Rice Lake

Rice Lake DMC-782 Bedienungsanleitung

Rice Lake

Rice Lake Survivor PL Bedienungsanleitung

Rice Lake

Rice Lake Survivor RT Leitfaden

Rice Lake

Rice Lake RoughDeck CC Caster Cargo Bedienungsanleitung

Rice Lake

Rice Lake Challenger 3 MSI-3460 Bedienungsanleitung

Rice Lake

Rice Lake Ishida IPC-WP Series Bedienungsanleitung

Rice Lake

Rice Lake CLS-M Bedienungsanleitung

Rice Lake

Rice Lake TC Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

Rice Lake

Rice Lake iDimension PWD Benutzerhandbuch

Rice Lake

Rice Lake 250-10-4 Series Bedienungsanleitung

Rice Lake

Rice Lake 250-10-4 Series Bedienungsanleitung

Rice Lake

Rice Lake TA Plus Series Bedienungsanleitung

Rice Lake

Rice Lake DIGI DSX-1000 Bedienungsanleitung

Rice Lake

Rice Lake equipoise Bedienungsanleitung

Rice Lake

Rice Lake DHH-10 Bedienungsanleitung

Rice Lake

Rice Lake RoughDeck BDP Bedienungsanleitung

Rice Lake

Rice Lake ISHIDA Uni-3 Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung

Fidelity Electronics

Fidelity Electronics G2e Bedienungsanleitung