Rice Lake Versa-portion RLP-S Bedienungsanleitung

Versa-portion RLP-S/SM

Multi-Purpose Bench Scale

Operation Manual

115519

Contents

About This Manual ......................................................................................1

Introduction .................................................................................................1

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Operation .....................................................................................................2

On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Tare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Automatic Shut-Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Display Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Default Primary Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

G, lb and oz Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Calibration ..................................................................................................3

Software Version and Span State Check . . . . . . . . . . . . . . . . . . . . . . . . . 3

Performing a Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Enclosure Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Setting the SPEC Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Internal Count and A/D Count Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Appendix .....................................................................................................7

DC Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Battery Pack Replacement/Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Specifications .............................................................................................9

Versa-portion RLP-S/SM Limited Warranty ..............................................10

Specifications subject to change without notice.

Rice Lake Weighing Systems is an ISO 9001 registered company.

Version 2 12/2011

Introduction 1

1.0 Introduction

bThe Versa-portion RLP-S/SM is a multi-purpose bench scale that offers practical

solutions for a full range of applications. Its internal resolution of 1/90,000 gives

you maximum precision and accuracy. Its backlit LCD display enables operators

to easily see weights. When portability is required, choose the optional

rechargeable battery for over 60 hours of continuous usage. The Versa-portion

RLP-S/SM is designed to reliably operate in many environments and withstand

transport from one area of the plant to another or from one business to the next.

This manual can be viewed or downloaded from the RLWS website at

www.ricelake.com/manuals.

1.1 Safety

Safety Signal Definitions:

WARNING

Important

CAUTION

WARNING

Indicates a potentially hazardous situation that, if not avoided could result in

serious injury or death, and includes hazards that are exposed when guards

are removed.

Indicates a potentially hazardous situation that, if not avoided may result in

minor or moderate injury.

Indicates information about procedures that, if not observed, could result in

damage to equipment or corruption to and loss of data.

General Safety

Do not operate or work on this equipment unless you have read and

understand instructions in the manual. Failure to follow the instructions or

heed the warnings could result in injury or death. Contact any Rice Lake

Weighing Systems dealer for replacement manuals. Proper care is your

responsibility.

Failure to heed may result in serious injury or death.

DO NOT allow minors (children) or inexperienced persons to operate this unit.

DO NOT operate without all shields and guards in place.

DO NOT jump on the scale.

DO NOT use for purposes other then weight taking.

DO NOT place fingers into slots or possible pinch points.

DO NOT use any load bearing component that is worn beyond 5% of the original dimension.

DO NOT use this product if any of the components are cracked.

DO NOT exceed the rated load limit of the unit.

DO NOT make alterations or modifications to the unit.

DO NOT remove or obscure warning labels.

Keep hands, feet and loose clothing away from moving parts.

2Versa-portion RLP-S/SM Operation Manual

1.2 Front Panel

Table 1-1 lists the indications and front-panel buttons available on the Versa-

portion RLP-S/SM.

Table 1-1. Versa-portion RLP-S/SM Indications and Front-Panel Buttons

Indication Description

On when the weight display is in ounces

*(not available in Versa-portion RLP-SM)

On when the weight display is in pounds

*(not available in Versa-portion RLP-SM)

(kg)

On when the weight display is in grams

*(Versa-portion RLP-SM value is kg, display is in kilograms)

On when the zero point is adjusted and the weight is stable

On when tare subtraction is performed

On (blinking) when the battery is weak and needs to be recharged

Front-Panel Button Description

Resets the weight display to zero

Sets or clears the tare value

Turns the display on/off

Changes measurement units between lb, oz, g, kg

(not available in Versa-portion RLP-SM)

2Versa-portion RLP-S/SM Operation Manual

2.0 Operation

2.1 On/Off

1.Press the POWER key. The display will blink 8.8.8.8.8.8. and show 0.000 when ready

to weigh.

2.2 Tare

Tare values can be used for up to half of scale capacity.

Performing a Tare

1.Place the item to be tared (typically a container) on the platter.

2.Press the TARE key.

3.The display will show 0.000 with the tared item on the platter.

Removing a Stored Tare

1.Remove the tared item from the platter.

2.Press the TARE key.

3.The display will show 0.000.

2.3 Automatic Shut-Off Timer

The Versa-portion RLP-S/SM has a built-in automatic shut-off timer. This timer can be set

to turn the unit off after three minutes of inactivity or 10 minutes of inactivity.

Setting the Timer for Three Minutes

1.If the unit is powered on, press the POWER key until it shuts down.

2.With the unit powered off, press and hold the POWER key for three seconds.

The display will show 3.

3.Release the POWER key. The timer is now set to turn the unit off after three minutes of

inactivity.

Setting the Timer for 10 Minutes

1.If the unit is powered on, press the POWER key until it powers off.

2.With the unit powered off, press and hold the POWER key for six seconds.

The display will show 3after a period of three seconds. It will show 10 after six

seconds.

3.Once the display shows 10, release the POWER key. The timer is now set to turn the

unit off after 10 minutes of inactivity.

Disabling the Timer

1.If the unit is powered on, press the POWER key until it shuts down.

2.With the unit powered off, press and hold the POWER key for nine seconds.

The display will show 3after a period of three seconds and 6after six seconds. It will

show 999 after nine seconds.

3.Once the display shows 999, release the POWER key. The timer is now disabled.

2.4 Display Brightness

The Versa-portion RLP-S/SM display brightness can be set to one of three levels.

Changing the brightness setting

1.Hold the ZERO key and press Ta r e three times.

2.Press the ZERO key to increase the dimmer level and the Power button to decrease the

dimmer level.

3.The display will show 1, 2, 3, or 4depending on which dimmer level is being

displayed.

4.Press the TARE key to save the setting and return to weigh mode.

Operation 3

2.5 Default Primary Unit

The Units button cycles through g, lb, and oz. (Versa-portion RPL-SM is only available in

kg)

Setting the Default Primary Unit

1.Hold the ZERO key and press the UNITS key three times.

2.Press the POWER key to cycle through available units.

3.When the desired default unit is displayed, press the TARE key to save the setting and

return to weigh mode.

2.6 G, lb and oz Conversion

(Not available in Versa-portion RLP-SM)

G, lb and oz conversion is available only when SPEC08=011 (see Section 3.4).

1.Switch between units by pressing the UNITS key.

Note

(G) uppercase is the abbreviation for gross.

(g) lowercase is the correct abbreviation for grams.

Calibration 3

3.0 Calibration

To enter calibration mode, remove the screw on the bottom of the scale as shown

in Figure 3-1. Use a small tool to press the span setup switch located under the

screw. Setup will time out to verify the switch is set to the ON position. Then,

perform a span switch state check (see Section 3.1).

Remove Screw

Figure 3-1. Setup Switch

3.1 Software Version and Span State Check

1.With the unit in weigh mode, press and hold the ZERO key.

2.With the ZERO key held, press and release the POWER key three times.

3.The display will show the software version for two seconds, then show the

current span switch state (S-ON or S-OFF).

After three seconds, the unit will return to weigh mode.

3.2 Performing a Calibration

The Versa-portion RLP-S/SM must be calibrated in grams or kilograms, and

SPEC 01 and 02 must be set for the gram value (or kg in the SM version). See

Section 3.4.

1.With the unit in weigh mode, press and hold the ZERO key.

2.With the ZERO key held, press and release the POWER key twice, then press

and release the TARE key.

The display will show CAL00.

Note

4Versa-portion RLP-S/SM Operation Manual

To exit calibration at any time, press the TARE key.

3.Ensure there is no weight on the platter, then press the ZERO key to

calibrate the zero point.

The display will show dashes, then CALSP.

4.Place the scale’s full capacity weight on the platter and press the ZERO key to

calibrate span.

The display will show dashes, then the weight value.

Calibration weight is full grams capacity. Full capacity values are as

follows: RLP-6S = 3000 g (3 kg);



RLP-15S = 6000 g (6 kg); RLP-30S = 15000 g (15 kg); RLP-60S = 30000 g

(30 kg).

5.The scale will return to weigh mode automatically. Power down the unit.

6.Calibration is complete.

3.3 Enclosure Security

After an NTEP inspector has examined the unit, he/she will install security cables

through three bolts on the underside of the scale. These cables prevent the unit

from being tampered with by an unauthorized individual. If the cable is removed,

NTEP certification will become void.

Figure 3-2. Legal for trade seal; cable passes through three bolts

3.4 Setting the SPEC Value

The SPEC value is used to specify decimal point position, minimum display, net/

gross multi-interval, resolution, weight single or multi-interval, decimal point

figure, negative weight display mask, IR mode protection (SPAN switch must be

turned on to allow calibration), start range (amount of weight that can be on the

scale when it is turned on), re-zero range, manual tare cancellation, tare

subtraction, tare accumulation, auto tare, weight reset, tare auto clear, zero

tracking, re-zero, and the UNIT key function. See Table 3-1 on page 5.

1.Press the setup switch (see Figure 3-1).

2.With the unit in weigh mode, press and hold the ZERO key.

Andere Handbücher für Versa-portion RLP-S

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rice Lake Skala Handbücher

Rice Lake

Rice Lake 350-10-8S Bedienungsanleitung

Rice Lake

Rice Lake RL350 Series Bedienungsanleitung

Rice Lake

Rice Lake DIGI DC-300 Series Bedienungsanleitung

Rice Lake

Rice Lake RL101 Bedienungsanleitung

Rice Lake

Rice Lake 350-10-8S Bedienungsanleitung

Rice Lake

Rice Lake Survivor RT Leitfaden

Rice Lake

Rice Lake Summit 3000 Bedienungsanleitung

Rice Lake

Rice Lake TuffSeal JB4ES Bedienungsanleitung

Rice Lake

Rice Lake CLS420 Bedienungsanleitung

Rice Lake

Rice Lake Digi DI-28 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

Rice Lake

Rice Lake Ishida Uni-7 Series Bedienungsanleitung

Rice Lake

Rice Lake DIGI DS-425 Bedienungsanleitung

Rice Lake

Rice Lake RL-DBS Betriebsanleitung

Rice Lake

Rice Lake 250-10-4 Series Bedienungsanleitung

Rice Lake

Rice Lake DHH-10 Bedienungsanleitung

Rice Lake

Rice Lake MSI-9600 Bedienungsanleitung

Rice Lake

Rice Lake Multiple Animal Scale Portable Beilage

Rice Lake

Rice Lake TC Bedienungsanleitung

Rice Lake

Rice Lake DIGI DC-150 Bedienungsanleitung

Rice Lake

Rice Lake RoughDeck FXB Bedienungsanleitung

Rice Lake

Rice Lake DIGI DC-200 Bedienungsanleitung

Rice Lake

Rice Lake ISHIDA Uni-3 Bedienungsanleitung

Rice Lake

Rice Lake Summit SB-1000 Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung

Fidelity Electronics

Fidelity Electronics G2e Bedienungsanleitung