Ricoh Aficio SP 4110n Bedienungsanleitung

Model No.

Information

Introduction

This manual contains detailed instructions and notes on the operation and use

of this machine. For your safety and benefit, read this manual carefully before

using the machine. Keep this manual in a handy place for quick reference.

Power Source

120 V, 60 Hz, 8 A or more

Please be sure to connect the power cable to a power source as above.

Laser Safety

This machine is considered class I laser device, safe for office/ EDP use. The ma-

chine contains 6.2 milliwatt, 770 - 795 nanometer wavelength, AlGaAs laser di-

odes. Safety precautions and interlock mechanisms have been designed to

prevent any possible laser beam exposure to the operator.

Important

Contents of this manual are subject to change without prior notice. In no event

will the company be liable for direct, indirect, special, incidental, or consequen-

tial damages as a result of handling or operating the machine.

Caution

Use of controls or adjustments or performance of procedures other than those

specified in this manual might result in hazardous radiation exposure.

SincereP1_Safety-EN_F_FM_forPaper.book Page 1 Tuesday, October 24, 2006 12:10 PM

Prohibition

Do not copy or print any item for which reproduction is prohibited by law.

Copying or printing the following items is generally prohibited by local law:

bank notes, revenue stamps, bonds, stock certificates, bank drafts, checks, pass-

ports, driver's licenses.

The preceding list is meant as a guide only and is not inclusive. We assume no

responsibility for its completeness or accuracy. If you have any questions con-

cerning the legality of copying or printing certain items, consult with your legal

advisor.

Notes

Two kinds of size notation are employed in this manual. With this machine refer

to the inch version.

For good print quality, the supplier recommends that you use genuine toner,

maintenance kits and parts from the supplier.

The supplier shall not be responsible for any damage or expense that might re-

sult from the use of consumables (toner, maintenance kits and parts) other than

genuine consumables from the supplier with your office products.

Some illustrations in this manual might be slightly different from the machine.

Certain options might not be available in some countries. For details, please con-

tact your local dealer.

SincereP1_Safety-EN_F_FM_forPaper.book Page 2 Tuesday, October 24, 2006 12:10 PM

Safety Information

When using your printer, the following safety precautions should always be fol-

lowed.

In this manual, the following important symbols are used:

RWARNING:

Indicates a potentially hazardous situation which, if instructions are not followed, could result

in death or serious injury.

Indicates a potentially hazardous situation which, if instructions are not followed, may result

in minor or moderate injury or damage to property.

•Confirm the wall outlet is near the machine and freely accessible, so

that in the event of emergency, it can be unplugged easily.

•Plug and unplug the power cable with dry hands, or an electric shock

could occur.

•Only connect the machine to the power source described in the manual.

•Avoid multi-wiring.

•Do not damage, break or make any modifications to the power cord.

Do not place heavy objects on it, pull it hard or bend it more than nec-

essary. These actions could cause an electric shock or fire.

•Do not incinerate spilled toner or used toner. Toner dust is flammable

and might ignite when exposed to an open flame.

•Do not take apart or attempt any modifications to this machine. There

is a risk of fire, electric shock, explosion or loss of sight. If the ma-

chine has laser systems, there is a risk of serious eye damage.

•Do not handle the power cord or plug with wet hands. Doing so might

cause an electrical shock.

•Keep the machine away from flammable liquids, gases, and aerosols.

A fire or an electric shock might occur.

•To avoid possible build-up of ozone, locate this machine in a large well

ventilated room that has an air turnover of more than 30 m3/hr/person.

•Do not store toner, used toner, or toner containers in a place with an

open flame. The toner might ignite and cause burns or a fire.

•Do not remove any covers or screws other than those specified in this

manual. Some parts of the machine are at a high voltage and could

give you an electric shock. Also, if the machine has laser systems, di-

rect (or indirect) reflected eye contact with the laser beam may cause

serious eye damage. When the machine needs to be checked, adjust-

ed, or repaired, contact your service representative.

SincereP1_Safety-EN_F_FM_forPaper.book Page 3 Tuesday, October 24, 2006 12:10 PM

RWARNING:

RCAUTION:

•Do not take apart or attempt any modifications to this machine. There

is a risk of fire, electric shock, explosion or loss of sight. If the ma-

chine has laser systems, there is a risk of serious eye damage.

•The supplied power cord is for use with this equipment only. Do not

use with other appliances. Doing so may result in fire, electric shock,

or injury.

•Do not pull out the paper tray forcefully. If you do, the tray might fall and

cause an injury.

•The inside of this printer becomes very hot. Do not touch parts labelled “v”

(indicating a hot surface). Touching these parts will result in burns.

•Keep the machine in an area that is within optimum environmental condi-

tions. Operating the machine in an environment that is outside the recom-

mended ranges of humidity and temperature can cause an electrical fire

hazard. Keep the area around the socket free of dust. Accumulated dust

can become an electrical fire hazard.

•Place the machine on a strong and level surface. Otherwise, it might fall and

injure someone.

•If toner or used toner is inhaled, gargle with plenty of water and move into

a fresh air environment. Consult a doctor if necessary.

•If your skin comes into contact with toner or used toner, wash the affected

area thoroughly with soap and water.

•If toner or used toner gets into your eyes, flush immediately with large

amounts of water. Consult a doctor if necessary.

•If toner or used toner is swallowed, dilute by drinking a large amount of wa-

ter. Consult a doctor if necessary

•Avoid getting toner on your clothes or skin when removing a paper jam or

replacing toner. If your skin comes into contact with toner, wash the affected

area thoroughly with soap and water.

•If toner gets on your clothing, wash with cold water. Hot water will set the

toner into the fabric and may make removing the stain impossible.

•Keep toner (used or unused) and the toner bottle out of reach of children.

•Grip the plug, not the cord, when pulling the plug from the socket. Pulling

the cord causes wear and tear that can result in fire or electric shock.

•Wait at least one hour after power off before replacing parts. Not allowing

the printer to cool may result in burns.

•When lifting the paper feed unit, hold the bottom of it, and then lift it slowly.

Lifting it carelessly or dropping it may cause an injury.

SincereP1_Safety-EN_F_FM_forPaper.book Page 4 Tuesday, October 24, 2006 12:10 PM

RCAUTION:

•Dispose the used toner containers at an authorized dealer or approved col-

lection site. If you are going to dispose of the used toner containers your-

self, do so according to local regulations.

•If you use the machine in a confined space, ensure there is continuous air

circulation.

•When removing misfed paper, do not touch the fusing unit because it could

be very hot.

•The fusing unit becomes very hot. When installing a new fusing unit, turn off

the printer and wait at least an hour before replacing the old fusing unit. Not

allowing the unit to cool may result in burns.

•When pulling the paper tray out, be careful not to pull it strongly. If you do,

the tray might fall and cause an injury.

•When moving the machine, hold the inset grips at both sides, and then lift

the printer slowly. Lifting it carelessly or dropping it may cause an injury.

•Before installing options, the machine should be turned off and unplugged

for at least half an hour. Components inside the machine become very hot,

and can cause a burn if touched.

•Do not touch the inside of the controller board compartment. It may cause

a machine malfunction or a burn.

•Before moving the machine, unplug the power cord from the wall outlet. If

the cord is unplugged abruptly, it could become damaged. Damaged plugs

or cords can cause an electrical or fire hazard.

•When lifting the machine, use the grips on both sides. The machine could

break or cause on injury if dropped.

•The printer weighs about 17 kg (37.5 lb.). When lifting the machine, use the

inset grips on both sides. Otherwise the printer could break or cause injury

if dropped.

•When moving the printer after use, do not take out any of the Toners, Photo

Conductor Units, nor the Waste Toner Cartridge to prevent toner spill inside

the machine.

•Disposal should take place at an authorized dealer or an appropriate collec-

tion site.

•Do not place the controller board near or into fire, as the litium battery in-

side this machine will explode and cause a burn.

•Risk of explosion if battery is replaced by an incorrect type. Dispose of used

batteries according to the instructions.

SincereP1_Safety-EN_F_FM_forPaper.book Page 5 Tuesday, October 24, 2006 12:10 PM

Note

❒Under certain temperature and humidity conditions, printing may cause va-

pour to issue from paper. The standard tray (behind the control panel) may

emit steam during printing.

❒Our products are engineered to meet the highest standards of quality and

functionality. When purchasing expendable supplies, we recommend using

only those specified by an authorized dealer.

Important

❒Rating voltage of the connector for options: Max. DC 24 V.

❒Voltage must not fluctuate more than 10%.

SincereP1_Safety-EN_F_FM_forPaper.book Page 6 Tuesday, October 24, 2006 12:10 PM

Positions of

WARNING and

CAUTION labels

This machine has labels for RWARNING and RCAUTION at the positions

shown below. For safety, please follow the instructions and handle the machine

as indicated.

Do not incinerate toner or toner containers. Toner dust may cause flashback

when exposed to open flames.

The inside of this printer becomes very hot. Do not touch parts with this label

(indicating a hot surface). Touching these parts will result in burns.

The inside of this printer becomes very hot. Do not touch parts with this label

(indicating a hot surface). Touching these parts will result in burns.

The inside of this printer becomes very hot. Do not touch parts with this label

(indicating a hot surface). Touching these parts will result in burns.

AUB050S

SincereP1_Safety-EN_F_FM_forPaper.book Page 7 Tuesday, October 24, 2006 12:10 PM

ENERGY STAR Program

❖Low-power Mode (Energy Saver mode)

This printer automatically lowers its power consumption 5 minutes after the

last operation has been completed. To exit Low-power (Energy Saver) mode,

press any key on the control panel. For more information about how to con-

figure Energy Saver mode, see “Making Printer Settings Using the Control

Panel”, Software Guide as a HTML file on the CD-ROM.

❖Specifications

ENERGY STAR®Office Equipment Program

The ENERGY STAR®Office Equipment Program encourages energy conservation by promot-

ing energy efficient computers and other office equipment.

The program backs the development and dissemination of products that feature energy saving

functions.

It is an open program in which manufacturers participate voluntarily.

Targeted products are computers, monitors, printers, facsimiles, copiers, scanners, and multi-

function devices. Energy Star standards and logos are internationally uniform.

Energy Saver mode Power Consumption With Options : 7 W or less

Printer Only : 4.5 W

Default Time 5 minutes

SincereP1_Safety-EN_F_FM_forPaper.book Page 8 Tuesday, October 24, 2006 12:10 PM

Others

Symbols

In accordance with IEC 60417, this machine uses the following symbols for the

main power switch:

•ameans POWER ON.

•bmeans POWER OFF.

Note to users in the United States of America

Note

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential in-

stallation. This equipment generates, uses and can radiate radio frequency ener-

gy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be deter-

mined by turning the equipment off and on, the user is encouraged to try to cor-

rect the interference by one more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio /TV technician for help.

Caution

Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Caution (in case of 100BaseTX environment)

Properly shielded cables must be used for connections to host computer (and/or

peripheral) in order to meet FCC emission limits.

Network interface cable with ferrite core must be used for RF interference sup-

pression.

SincereP1_Safety-EN_F_FM_forPaper.book Page 9 Tuesday, October 24, 2006 12:10 PM

Declaration of Conformity

Product Name: Laser Printer

Model Number: MLP31n/MLP36n/P7031n/P7035n/LP131n/LP136n/Aficio

SP 4100N/Aficio SP 4110N

Responsible party: Ricoh Corporation

Address: 5 Dedrick Place, West Caldwell, NJ 07006

Telephone number: 973-882-2000

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

AThis device may not cause harmful interference, and

Bthis device must accept any interference received,

including interference that may cause undesired operation.

• Properly shielded cables must be used for connections to host computer

(and/or peripheral) in order to meet FCC emission limits.

• Network interface cable with ferrite core must be used for RF interference

suppression.

• Pour empêcher que cet appareil cause du brouillage au service faisant l'objet

d'une licence, il doit être utilisé à l'intérieur et devrait être placé loin des

fenêtres afin de fournir un écran de blindage maximal. Si le matériel (ou son

antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.

Note to users in Canada

Note

This Class B digital apparatus complies with Canadian ICES- 003.

IEEE 802.11b Interface Unit Type I (R-WL11B)

This device complies with RSS 210 of Industry Canada.

To prevent radio interference to the licensed service, this device must be operat-

ed indoors only and should be kept away from windows to provide maximum

shielding.

Remarque concernant les utilisateurs au Canada

Avertissement

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

SincereP1_Safety-EN_F_FM_forPaper.book Page 10 Tuesday, October 24, 2006 12:10 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ricoh Multifunktionsdrucker Handbücher

Ricoh

Ricoh C211 Bedienungsanleitung

Ricoh

Ricoh 5100WD Bedienungsanleitung

Ricoh

Ricoh Pro 8300S Bedienungsanleitung

Ricoh

Ricoh Aficio Color 4006 Bedienungsanleitung

Ricoh

Ricoh Aficio MP 161 Gebrauchsanweisung

Ricoh

Ricoh M000 Bedienungsanleitung

Ricoh

Ricoh Aficio 3224C Bedienungsanleitung

Ricoh

Ricoh M099 Handbuch

Ricoh

Ricoh MP 6503 Bedienungsanleitung

Ricoh

Ricoh Aficio MP C305 Bedienungsanleitung

Ricoh

Ricoh FAX5600L Bedienungsanleitung

Ricoh

Ricoh Pro 8100S Bedienungsanleitung

Ricoh

Ricoh A292 Bedienungsanleitung

Ricoh

Ricoh SP 201n Bedienungsanleitung

Ricoh

Ricoh MP C2003 Series Bedienungsanleitung

Ricoh

Ricoh M 2701 Bedienungsanleitung

Ricoh

Ricoh Aficio MP 5500 Bedienungsanleitung

Ricoh

Ricoh Aficio SP 100SF e Bedienungsanleitung

Ricoh

Ricoh B064 SERIES Bedienungsanleitung

Ricoh

Ricoh 8016 Bedienungsanleitung

Ricoh

Ricoh B022 Bedienungsanleitung

Ricoh

Ricoh A318 Bedienungsanleitung

Ricoh

Ricoh Pro C751 EX Bedienungsanleitung

Ricoh

Ricoh aficio 1013 Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung