Ricoh Di-C1.5a Bedienungsanleitung

Di-C1.5 Training

Slide 1

MODEL Di-C1.5 TRAINING

Machine Codes: D104/D106

INTRODUCTION

HOW TO USE THIS PRESENTATION

This TTP (Technical Training package) will help you train service technicians on the model Di-C1.5.

You can use this guide in three ways:

As a check list to make sure you have covered all the important points

As a set of ordered notes taken from the service manual, operation manual, and other sources.

Sometimes, the ideas from other manuals have been reworded or reorganized for clarity.

As a source of information that is not included in any of the other manuals. This may include

technical details of the machine’s hardware or software, or background knowledge of

technologies used in the machine. This information can be taught to the trainees if you feel that

they will benefit from it, but some of it may be too technical for routine field use. This information

may also help you answer questions from the class.

Caution: Do NOT give copies of this TTP to anyone other than trainees, technical training staff,

technical support staff, and management personnel. In particular, do not reveal this information to

competitors.

Some slides reformatted for easier Chinese

translation. (No content changes.)

V1.024 November 2010

First releaseV1.028 October 2010

DescriptionVersion HistoryDate of change

Di-C1.5 Training

Slide 2

Introduction

The Di-C1.5 is a low-range network multi-

functional color copier.

Based on the GW Architecture.

Provides the following:

» Network Scanning (color originals can be scanned)

» Local Storage (with the HDD)

» Copying

» Printing

PREPARATION CHECK LIST

Provide the relevant manuals and any additional handouts you feel are

necessary. Special tools are listed in the Replacement and Adjustment section of

the field service manual.

TCP/IP or wireless network1Network

For testing and document

storage.

1 per traineeComputer

Used for testing the printing

and document storage.

1 set per machineSpecial Tools

Have the trainees completely

install these during class.

1 for every 3 traineesTraining machines

Give copies to the trainees1 per traineeTraining Schedule

Give copies to the trainees1 per traineeOperation Manuals

Give copies to the trainees1 per traineeField Service Manual

RemarksQuantityDescription

Di-C1.5 Training

Slide 3

Objectives

Install the machine and its peripherals in the

field.

Understand and perform routine maintenance.

Understand the PM table.

Understand the important SP codes.

Troubleshoot and repair this product in the field.

ORIENTATION

Provide the trainees with information about the training course procedures, facilities,

objectives and rules.

Introduction of instructors

Introduce yourself to the class, and any other instructors who will be taking part. Tell

them who to talk to if they have any problems.

Introduction of trainees

Distribute a list of those attending the course.

Try to generate a friendly and relaxed atmosphere, and encourage the class to get to

know each other.

If it will help, have the trainees introduce themselves (name, company, work

experience).

Explanation of curriculum

Pass out copies of the training schedule

Impress the importance of getting to the class on time

Go over the course objectives (key points listed on the slide).

Explanation of training center rules

Explain the general rules of your training center (smoking, breaks, use of facilities, etc.)

Explain the tools and equipment available at the facility.

Impress on the trainees that they should not touch the machines until the instructor says

so, and that they are responsible for replacing tools and keeping the classroom in order.

Di-C1.5 Training

Slide 4

Di-C1.5 TRAINING

COURSE OVERVIEW

The course is broken up into several modules. This section outlines these

modules.

The course covers the base machine and the optional peripherals. Connectivity

is not covered in this course.

Di-C1.5 Training

Slide 5

Course Overview - 1

Product Outline

What's New

Specifications

Installation

Machine Overview

Scanner

Laser Exposure

PCDU

PRODUCT OUTLINE

The model will be introduced to the class.

The optional peripherals will be introduced to the class.

The product concept, sales points, and targets will be presented.

What's New

Changes from the Di-C1 will be listed.

SPECIFICATIONS

The main specifications will be outlined. Significant items will be stressed.

INSTALLATION

The class will install their machines and the peripherals.

The class will learn how to access SP modes and user tools.

The class will study how to upgrade the firmware.

MACHINE OVERVIEW

The components will be discussed.

The paper feed path and copying process will be outlined.

The machine's organization and overall PCB structure will also be covered.

SCANNER

The scanner mechanism will be discussed.

LASER EXPOSURE

The laser diode circuits and laser optics will be described.

PCDU

This section explains the components of the PCDU.

All the image-creation processes around the drum, including development, are covered

in this section.

Di-C1.5 Training

Slide 6

Course Overview - 2

Process Control

Toner Supply

Transfer

Paper Feed

Fusing

Paper Exit

Duplex

PROCESS CONTROL

This section explains the basic points about how the machine controls the copy

process to compensate for changes in operating conditions.

Toner supply control, and toner near-end/end detection are covered in this

section.

TONER SUPPLY

The toner supply mechanism will be described.

Toner supply control, and near-end/end detection are covered in the process

control section.

TRANSFER

Image transfer, paper transfer, and paper separation will be described.

PAPER FEED

The paper feed mechanism for the main body will be described. The optional tray

units will be dealt with in later sections.

FUSING

Fusing will be described.

PAPER EXIT

The paper feed out mechanisms will be described.

DUPLEX

The duplex mechanisms will be described.

The duplex unit is a standard component of this model.

Di-C1.5 Training

Slide 7

Course Overview - 3

Options

ARDF

Paper Tray Units (1-tray, 2-tray)

Shift Tray

One-bin Tray

Side Tray

Internal finisher

Maintenance

Troubleshooting

Fax Option

Environmental Conservation

Supplement: Coverage Counter

OPTIONS

The options listed above will be described in the indicated order.

MAINTENANCE

PM is described briefly.

TROUBLESHOOTING

Basic points concerning service codes, diagnostics, and other troubleshooting

tools will be covered.

FAX

Basic information about the fax unit will be explained.

Environmental Conservation

Technologies that have been implemented for environmental conservation will be

explained.

Supplement: Coverage Counter

Supplemental information about coverage counter calculations.

Di-C1.5 Training

Slide 8

Di-C1.5 TRAINING

PRODUCT OUTLINE

The model will be introduced.

The optional peripherals will be introduced.

The product concept, sales points, and targets will be presented.

Di-C1.5 Training

Slide 9

INTRODUCTION

No additional notes

Di-C1.5 Training

Slide 10

How many models?

Two models:

Di-C1.5a (D104): 20 cpm

Di-C1.5c (D106): 25 cpm

Copy speed is the only difference between the two models.

All models have the following equipment built-in:

Printer/scanner unit.

USB host

10-baseT/100-baseTX

Java VM

App2Me (must be installed by the technician during the machine’s

installation procedure)

Data Overwrite Security Unit

HDD Encryption Unit

SD cards

Slot 1 (upper slot): Security SD Card (contains the Data Overwrite

Security Unit and HDD Encryption Unit)

» Already installed at the factory; the technician does not have to do

anything when installing the machine. However, the customer must

activate them with user tools.

Slot 2 (lower slot): Empty when shipped from factory

» VM card with App2Me must be inserted during the machine’s

installation procedure.

App2Me: More about this later.

In the previous models, no SD cards were installed at the factory, and the Data

Overwrite Security Unit and HDD Encryption Unit were options.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ricoh Kopierer Handbücher

Ricoh

Ricoh A163 Bedienungsanleitung

Ricoh

Ricoh Aficio FX10 Bedienungsanleitung

Ricoh

Ricoh Gim-MF1a Kurzanleitung

Ricoh

Ricoh FT8880 Bedienungsanleitung

Ricoh

Ricoh Aficio 2035 Bedienungsanleitung

Ricoh

Ricoh FW750 Bedienungsanleitung

Ricoh

Ricoh G-P3 Bedienungsanleitung

Ricoh

Ricoh A229 Bedienungsanleitung

Ricoh

Ricoh Di-C1 Bedienungsanleitung

Ricoh

Ricoh PS430 Bedienungsanleitung

Ricoh

Ricoh 7700W Bedienungsanleitung

Ricoh

Ricoh Pro 8100S Bedienungsanleitung

Ricoh

Ricoh FT7950 Bedienungsanleitung

Ricoh

Ricoh FD5000 Bedienungsanleitung

Ricoh

Ricoh A183 Bedienungsanleitung

Ricoh

Ricoh Aficio DSm651 Bedienungsanleitung

Ricoh

Ricoh Pro1106X Bedienungsanleitung

Ricoh

Ricoh A193 Bedienungsanleitung

Ricoh

Ricoh A217 Bedienungsanleitung

Ricoh

Ricoh 8700W Bedienungsanleitung

Ricoh

Ricoh M281 Series Bedienungsanleitung

Ricoh

Ricoh FT5540 Bedienungsanleitung

Ricoh

Ricoh Aficio 480W Bedienungsanleitung

Ricoh

Ricoh MP 2014 Series Bedienungsanleitung

Beliebte Kopierer Handbücher anderer Marken

Canon

Canon iR1210 Referenzhandbuch

Minolta

Minolta CF910 Bedienungsanleitung

Xerox

Xerox EC70 Bedienungsanleitung

Oce

Oce 9800 Bedienungsanleitung

Olivetti

Olivetti d-Copia 1800 Bedienungsanleitung

Minolta

Minolta Di181 Bedienungsanleitung

Canon

Canon iR5000i Bedienungsanleitung

Telecrane

Telecrane F25 Bedienungsanleitung

Xerox

Xerox WorkCentre Pro 40 Bedienungsanleitung

Canon

Canon NP6317 Anleitung zur Verwendung

Sharp

Sharp AR-5015 N Bedienungsanleitung

Mita

Mita MIP-2400 Handbuch

Sharp

Sharp AL-2061 Bedienungsanleitung

Muratec

Muratec MFX-C2280 Bedienungsanleitung

Minolta

Minolta EP4000 Bedienungsanleitung

Triumph Adler

Triumph Adler DCC 2526 Handbuch

Kyocera Mita

Kyocera Mita KM-2030 Handbuch

Triumph Adler

Triumph Adler DC 2222 Handbuch