Ricoh R10 Gebrauchs- und Pflegehandbuch

Firmware Update Instruction Manual

This manual explains the procedures for downloading the RICOH R10 firmware from the Ricoh

website and updating the camera’s firmware.

Perform the following operations to update the firmware.

1. Check the firmware version

Caution

Before updating, be sure to check the firmware version through the following method. If the installed firmware is the latest

version, there is no need to update.

1. Making sure that the camera’s power is

turned off, switch the mode dial to SCENE.

2. While pressing the ADJ./OK button @,

hold down the 6(Playback) button for 2-

3 seconds.

• The firmware version will be displayed on the

picture display for about 20 seconds.

3. Check the firmware version displayed on

the picture display.

• e.g. When the firmware version is V1.00, the

version will be shown as [MAIN : V 1.00] as follows:

MAIN : V 1.00

BKUP : V X.XX

MONI : V X.XX

ADJD : V X.XX

EXTD : V X.XX

CPU1 : V X.XX

SH : XXXXXX

ST : XXXXXX

ADJ./OK Button

6(Playback) Button Mode dial

2. Extract the firmware

1. Download the firmware from the Ricoh website.

2. Double-click or right-click and select [Open] on the downloaded file.

• A dialog screen appears.

3. Click [OK].

• The folder [R10 Update] is created, and the firmware is extracted to the folder [Firmware

relX.XX (where X.XX is the version number)]. Check that [elaunch3] (firmware file),

[elaunch4] (extension file), and [elaunch8] (adjusted value file) are inside the folder

[Firmware relX.XX].

3. Copy the firmware to an SD memory card

There are two ways to copy the firmware into an SD memory card.

• With an SD memory card loaded in the camera, connect the camera and computer with the

provided USB cable, and copy the firmware to the SD memory card

• Using a card reader or a card writer, copy the firmware to an SD memory card (a card reader

or card writer is required)

To copy the firmware by connecting the camera and computer with the USB

cable

1. If DSC Software is installed on your Windows PC, check that DL-10 is not

active.

2. If DL-10 is active, right-click on the DL-10 icon in the task bar, and click

[Exit].

• If the DL-10 icon is not displayed in the task bar, you do not need to perform Step 2.

3. Load a battery with adequate remaining power into the camera.

4. Load the SD memory card into the camera, and turn the power on.

5. Display the camera’s Setup menu, select [Format [Card]], and press the

ADJ./OK button $.

elaunch3

elaunch4

elaunch8

elaunch3

elaunch4

elaunch8

For Windows For Macintosh

6. Select [Yes], and press the ADJ./OK button.

• The SD memory card is formatted.

Caution

If you format a card that still has images stored on it, the images will be lost. Save the images you do not want to erase in

your computer before formatting the card.

7. Turn the camera off, and connect the camera and computer with the

provided USB cable.

• The camera turns on automatically. If the camera does not turn on automatically, press the

POWER button and turn the power on.

• If DSC Software is installed in your Windows PC, DL-10 may automatically start up. In this

case, exit DL-10.

• Click [Cancel] if the [Removable Disk] dialog appears in Windows XP or Windows Vista.

• If iPhoto starts up in Mac OS X, exit iPhoto.

8. Copy the files [elaunch3], [elaunch4], and [elaunch8] (created when the

firmware was extracted) into [RICOHDCX] in [My Computer].

• The camera’s drive name may differ depending on the OS you are running.

e.g. [Removable Disk], etc.

9. Open [RICOHDCX] in [My Computer], and confirm that the firmware is

copied as below.

elaunch3

elaunch4

elaunch8

RICOHDCX

elaunch3

elaunch4

elaunch8

For Windows For Macintosh

RICOHDCX

DCIM

elaunch4

elaunch3

elaunch8

RICOHDCX

DCIM

elaunch3

elaunch4

elaunch8

Example of display in Windows Example of display in Macintosh

10.For Windows

When the copying of the firmware is completed, double-click the [Safely

Remove Hardware] icon in the task bar.

For Macintosh

Drag and drop the [RICOHDCX] icon to the [Trash] icon. Once the icon

has disappeared, proceed to Step 14.

Caution

If you skip the procedures in Step 10, the firmware copy may not be successful.

11.Select [USB Mass Storage Device], and click [Stop].

12.Click [OK].

13.Click the [Close] button.

14.Turn the camera off, and disconnect the USB cable.

To copy the firmware using a card reader or a card writer to an SD memory

card

1. Load the SD memory card into the camera, and turn the power on.

2. Display the camera’s Setup menu, select [Format [Card]], and press the

ADJ./OK button $.

3. Select [Yes], and press the ADJ./OK button.

• The SD memory card is formatted.

Caution

If you format a card that still has images stored on it, the images will be lost. Save the images you do not want to erase in

your computer before formatting the card.

4. Turn the camera off, and remove the SD memory card.

5. Copy the files [elaunch3], [elaunch4], [elaunch8] (created when the

firmware was extracted) into the root directory of the SD memory card.

6. Load the camera with the SD memory card which the firmware was copied

to.

4. Update the firmware

1. Making sure that the camera’s power is

turned off, switch the mode dial to SCENE.

2. While pressing the ADJ./OK button !,

hold down the 6(Playback) button for 2-

3 seconds.

• A confirmation message for the firmware update is

displayed on the picture display.

3. Press the ADJ./OK button $to select

[Yes], and press the ADJ./OK button.

• The firmware update starts, and the following

message is displayed on the picture display.

[Checking rewrite file]

[Rewriting program]

The update is completed in about 40 seconds.

• The camera's power turns off automatically.

4. The camera automatically turns off and restarts.

•If the message [Incorrect rewriting file] is displayed and the camera is automatically turned off, check the camera model

again and retry the update using the correct firmware.

•The firmware file copied to the SD memory card is deleted when you format the SD memory card. Delete the file if

necessary.

ADJ./OK Button

6(Playback) Button Mode dial

Andere Handbücher für R10

Inhaltsverzeichnis

Andere Ricoh Digitalkamera Handbücher

Ricoh

Ricoh R8 Bedienungsanleitung

Ricoh

Ricoh PENTAX K-1 II Bedienungsanleitung

Ricoh

Ricoh Pentax K-3 II Bedienungsanleitung

Ricoh

Ricoh PDC-i700 Bedienungsanleitung

Ricoh

Ricoh PENTAX K-3 Bedienungsanleitung

Ricoh

Ricoh R50 Bedienungsanleitung

Ricoh

Ricoh Pentax K-S2 Leitfaden

Ricoh

Ricoh Pentax K-3 III Gebrauchs- und Pflegehandbuch

Ricoh

Ricoh CX3 Bedienungsanleitung

Ricoh

Ricoh WG-30 Bedienungsanleitung

Ricoh

Ricoh Singlex Bedienungsanleitung

Ricoh

Ricoh RDC-300Z series Bedienungsanleitung

Ricoh

Ricoh CX1 Bedienungsanleitung

Ricoh

Ricoh Caplio R1 Bedienungsanleitung

Ricoh

Ricoh Caplio GX8 Bedienungsanleitung

Ricoh

Ricoh CAPILO G4 Bedienungsanleitung

Ricoh

Ricoh G700SE Sicherheitsleitfaden

Ricoh

Ricoh R50 Bedienungsanleitung

Ricoh

Ricoh WG-5 GPS Leitfaden

Ricoh

Ricoh WG-4 GPS Bedienungsanleitung

Ricoh

Ricoh Caplio RR-1 Bedienungsanleitung

Ricoh

Ricoh WG-60 Leitfaden

Ricoh

Ricoh DIACORD L Bedienungsanleitung

Ricoh

Ricoh Caplio GX100 Bedienungsanleitung

Beliebte Digitalkamera Handbücher anderer Marken

Mercury

Mercury 350K Bedienungsanleitung

Pentax

Pentax Optio LS 465 Bedienungsanleitung

Sanyo

Sanyo VPC-S1085 Bedienungsanleitung

GE SMART A1255 Bedienungsanleitung

Point Grey

Point Grey Gazelle Bedienungsanleitung

Nikon

Nikon COOLPIX A Bedienungsanleitung

Pentax

Pentax P-5 Bedienungsanleitung

BlazeVideo

BlazeVideo A280 Bedienungsanleitung

Sony

Sony MCA-20 Bedienungsanleitung

Sony

Sony Alpha DSLR-A290 Bedienungsanleitung

ATIK Cameras

ATIK Cameras One Bedienungsanleitung

CohuHD Costar

CohuHD Costar 3930 Series Bedienungsanleitung

Leica

Leica M10-R Bedienungsanleitung

FujiFilm

FujiFilm FinePix A700 Bedienungsanleitung

Lorex

Lorex LNZ81P25 Series Bedienungsanleitung

GE J1470S Bedienungsanleitung

Sony

Sony A6700 Benutzerhandbuch

Canon

Canon EOS ELAN7 Bedienungsanleitung