Ricoh S7 D3DS Kurzanleitung

Double-feed Kit S7

Machine Code:D3DS

Field Service Manual

Ver 1.0

Latest Release: Nov, 2016

Initial Release: Nov, 2016

Table of Contents

1. Install.................................................................................................................................................................................. 2

Double-feed Kit S7 D3DS..................................................................................................................................................... 2

Accessories........................................................................................................................................................................ 2

Installation.......................................................................................................................................................................... 3

1.Install

Install

Double-feed Kit S7 D3DS

Accessories

No.

Description

Q’ty

1 Double-feed Sensor 1 (Emitter) 1

2 Double-feed Sensor 2 (Receiver) 1

3 Double-feed Sensor Board 1

4 Clamp 1

5 Long Harness (2-pin) 1

6 Long Harness (7-pin) 1

7 Shielded Harnesses 1

8 Short Harness (13-pin) 1

9 Screws M3x6 4

10 Screws M3x8 2

1.Install

Installation

Remove ADF Covers

1. Set the saddle clamp on the double-feed sensor board.

2. At the back of the machine, remove the cap and screw from the rear cover.

3. Raise the feed cover, and then remove the screw from the top edge of the rear cover.

4. Press the tab [A] on the end of the rear cover to release the cover, and then rotate the cover [B] down slowly.

1.Install

5. Disconnect the bottom tabs, and then remove the rear cover.

6. At the front, raise the ADF slightly.

7. Disconnect the top edge of the front cover. The embossed arrow [A] shows which direction to slide the cover to

unlock the tabs..

1.Install

8. Push the front cover [A] to the left, and then remove it [B].

9. Lower the ADF.

Remove Feed Cover, Upper Guide

1. At the left rear corner of the ADF, disconnect and free the shielded harnesses.

1.Install

2. At the front, remove the pivot screw.

3. Disconnect the hinge arm.

4. Carefully disconnect the cover at the rear [A].

5. At the front, disconnect the hinge arm [B].

1.Install

6. Remove the feed cover.

7. Lay the feed over on a flat clean surface as shown, and then disconnect the upper guide.

8. Release the edge of the upper guide from the posts.

9. Swing the upper guide up, and then remove it.

Remove Original Shielded Harnesses

1. Turn the upper guide [A] upside down.

1.Install

2. Disconnect the ground wire [B].

3. Remove the sensor bracket.

4. Disconnect the skew correction sensor [A] (white connector).

5. Disconnect the separation sensor [B] (black connector).

•These sensor harnesses must be re-connected as shown.

Inhaltsverzeichnis

Andere Ricoh Druckerzubehör Handbücher

Ricoh

Ricoh F-40 Bedienungsanleitung

Ricoh

Ricoh SR3180 Kurzanleitung

Ricoh

Ricoh Aficio 3030 Bedienungsanleitung

Ricoh

Ricoh PB1170 Kurzanleitung

Ricoh

Ricoh D014 Bedienungsanleitung

Ricoh

Ricoh D109 Handbuch

Ricoh

Ricoh PB1080 Kurzanleitung

Ricoh

Ricoh RT5120 Kurzanleitung

Ricoh

Ricoh Lily Bedienungsanleitung

Ricoh

Ricoh Aficio SG 3110DN Bedienungsanleitung

Ricoh

Ricoh TR5050 Kurzanleitung

Ricoh

Ricoh PB3150 Kurzanleitung

Ricoh

Ricoh A-P3 Bedienungsanleitung

Ricoh

Ricoh Priport DX 4640PD Bedienungsanleitung

Ricoh

Ricoh CF5010 Bedienungsanleitung

Ricoh

Ricoh Aficio SP 4310N Bedienungsanleitung

Ricoh

Ricoh G165 Bedienungsanleitung

Ricoh

Ricoh CS4010 Kurzanleitung

Ricoh

Ricoh PB2030 Kurzanleitung

Ricoh

Ricoh FAX Option Type 3030 Bedienungsanleitung

Ricoh

Ricoh TK2000 Bedienungsanleitung

Ricoh

Ricoh Aficio AP4510 Stücklistenhandbuch

Ricoh

Ricoh LCIT RT5100 Kurzanleitung

Ricoh

Ricoh Aficio 3228C Bedienungsanleitung

Beliebte Druckerzubehör Handbücher anderer Marken

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

REA

REA JET HR pro 2K Bedienungsanleitung

HP Laserjet,Color Laserjet 4si Bedienungsanleitung

oliser

oliser MS 45 Bedienungsanleitung

Roland

Roland DU2-64 Anleitungen und Rezepte

Xerox

Xerox EFI EXP6000 Bedienungsanleitung

Canon

Canon Finisher-T1 Bedienungsanleitung

Sharp

Sharp FO-1MK Bedienungsanleitung

Labelmate

Labelmate PM-300 Bedienungsanleitung

Epson

Epson T6248 Betriebsanleitung

Epson

Epson OT-BZ20 Bedienungsanleitung

Canon

Canon TonerRobot EP-27 Bedienungsanleitung

GBC

GBC 16 Series Bedienungsanleitung

Canon

Canon INNER 2-WAY TRAY-E1 Bedienungs- und Wartungshandbuch

Develop

Develop SD-509 Bedienungsanleitung

Kyocera

Kyocera KM-6230 Handbuch

Triumph Adler

Triumph Adler DF-710 Handbuch

Citizen

Citizen CBM-202PC Series Bedienungsanleitung