Ricoh EMP 156 Bedienungsanleitung

Transit Pass Unit Type156

Installation

Manual

Sep, 2006

N904131

Revision Table for manual

Rev. for

Manual

Machine

Rev. Page No.(Contents) Date

00 - FIRST EDITION May.26, ’06

01 - 2-4, 2-6, 4-2 (Addition of the BS Plate Assembly) Sep.21, ’06

4-6 (Addition of the Configuration of Post Device)

Front cover,Table,Safety2,Safety3,1-1,2-1,2-3,3-1,3-2,

4-1,4-2,4-3,4-4,4-5,4-6 (Change of the product name)

No part of this document may be reproduced without the expressed permission of Ricoh Printing

Systems, Ltd.

The material in this document is for informational purposes and is subject to change without notice.

Ricoh Printing Systems, Ltd. assumes no responsibility for errors or omissions in this document. No

liability is assumed for any damages resulting from the use of the information it contains.

This manual describes information for handling and operating the Transit Pass Unit Type156.

NOTICE TO USER

In an effort to meet the demands of a rapidly changing technology, the manufacturer is continually

developing new features and functions to meet your changing printing or Transit Pass Unit

Type156 needs. As a result, this manual may not exactly reflect future changes made to the

product. Please be sure to consult all manual updates or addenda when using this product’s

documentation.

INTRODUCTION

This manual provides essential information to install the Transit Pass Unit Type156

Carefully read and understand the safety instructions in this manual before starting installation.

Keep this manual on hand for reference.

BLANK

Table of Contents i

II L 00

Table of Contents

SAFETY SUMMARY

1. General Safety Guidelines …………………………………………………………………. Safety-1

2. Hazard Warning Statements ……………………………………………………………… Safety-2

2.1 WARNING Statement …………………………………………………………………. Safety-2

CHAPTER 1. INSTALLATION REQUIREMENTS ........................................1-1

1.1 APPLICATION ......................................................................................................................1-1

1.2 INSTALLATION AREA ...........................................................................................................1-1

1.3 PREPARATION FOR INSTALLATION .......................................................................................1-1

1.4 TOOLS REQUIRED..............................................................................................................1-2

1.5 ENVIRONMENTAL CONDITIONS ...........................................................................................1-2

CHAPTER 2. UNPACKING ............................................................................2-1

2.1 UNPACKING OF THE TRANSIT PASS UNIT TYPE156 ............................................................2-1

2.1.1 Confirmation of parts quantities ........................................................................................... 2-1

2.1.2 Unpacking Procedures ........................................................................................................ 2-2

2.1.3 Parts check in the Parts Box................................................................................................ 2-4

CHAPTER 3. PREPARATION FOR INSTALLATION...................................3-1

3.1 PREPARATION FOR INSTALLATION OF THE PASS UNIT..........................................................3-1

3.2 PREPARATION FOR INSTALLATION OF THE STACKER ............................................................3-3

CHAPTER 4. INSTALLATION ........................................................................4-1

4.1 INSTALLATION OF TRANSIT PASS UNIT TYPE156.................................................................4-1

4.2 INSTALLATION OF CABLE.....................................................................................................4-3

4.3 ADJUSTMENT OF LEVELING HEIGHT.....................................................................................4-5

4.4 ATTACHING COVERS...........................................................................................................4-6

4.5 CONFIGURATION OF POST DEVICE .....................................................................................4-6

APPENDIX 1. INSTRATION AREA INFORMATION

SAFETY SUMMARY

Safety 1

II L 00

The hazard warnings which appear on the warning labels on the machine or in the manual have one of

the following alert headings consisting of an alert symbol and a signal word, DANGER, WARINIG, or

CAUTION.

This is the safety alert symbol. It is used to alert you to potential personal

injury hazards. Obey all safety messages that follow this symbol to avoid

possible injury or death.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result

in death or serious injury.

WARNING: Indicated a potentially hazardous situation which, if not avoided, can result

in death or serious injury.

CAUTION: Indicates a hazardous situation which, if not avoided, will or can result in

minor or moderate injury, or serious damage of product.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in property damage.

1. General Safety Guidelines

Before operating the machine, read the following instructions carefully:

 Follow all the installation procedures provided in this manual.

 Pay special attention to and follow all the hazard warnings on the machine and in the manual.

Failure to do so can cause injury to yourself or damage to the machine.

 Do not perform any installation in any way other than as provided in this manual.

 Keep in mind that the hazard warnings in this manual or on the machine cannot cover every

possible case, as it is impossible to predict and evaluate all circumstances beforehand. Be alert

and use your common sense.

SAFETY SUMMARY (Continued)

Safety 2

II L 00

2. Hazard Warning Statements

The following are the hazard warning statements contained in this manual.

2.1 WARNING Statement

 Keep space at the rear of the Transit Pass Unit Type156 for ventilation. Otherwise, cooling of the

equipment does not done properly and print Quality may be degraded. (Refer to Figure in the

Appendix.

for the area of the space.)

(Section 1.2,Page 1-1)

 Be careful when unpacking using the crane or forklift. Do not to drop the Transit Pass

Unit Type156, hit it against something, or turn it over on its side.

(Section 2.1,Page 2-1)

 Perform unpacking where there is no dust or water leaking.

(Section 2.1,Page 2-1)

 Do not place heavy objects which weigh 5 kg or more on the Transit Pass Unit Type156.

(Section 2.1,Page 2-1)

 Be careful when lifting the Transit Pass Unit Type156 with the forklift so the Transit Pass

Unit Type156 is well-balanced on the arms of the lift. Also put the packing (cushion)

between the Transit Pass Unit Type156 and the forklift so the printer is not damaged.

(Section 2.1,Page 2-1)

SAFETY SUMMARY (Continued)

Safety 3

II L 00

 Observe the speed limit of 300 mm/sec. (1.08 km/hr) when moving the Transit Pass

Unit Type156. Do not move the Transit Pass Unit Type156 on unleveled floor. Do not

tilt the Transit Pass Unit Type156 15 deg. or more.

(Section 2.1,Page 2-1)

 Choose the route to move the Transit Pass Unit Type156 where the slope is less than 15

deg.

(Section2 .1,age 2-1)

 Do not push in the direction of the arrow at the movement of the Transit Pass Unit

Type156. There is danger to which it falls.

(Section 2.1,Page 2-1)

 Choose the location to place the Transit Pass Unit Type156 where there is no condensation.

(Section 2.1,Page 2-1)

Unpacking 1-1

II L 00

Chapter 1. Installation Requirements

1.1 Application

These specifications are applicable to the Transit Pass Unit Type156, installation and

adjustment.

1.2 Installation Area

Installation area is shown in Appendix 1.

Keep space at the rear of the Transit Pass Unit Type156 for ventilation.

Otherwise, cooling of the equipment does not done properly and

print Quality may be degraded. (Refer to Figure in the Appendix 1 for

the area of the space.)

1.3 Preparation for installation

Make sure the floor where the leveling bolts to be mounted is strong enough. If the floor is not

strong enough, the equipment may tilts and may cause paper handling problem.

High Capacity

Feeder 2

(Option)

High Capacity

Feeder 1

(Option)

Jack screw

and Caster

Area (Φ95)

Jack Screw

Caster Rotation

Area (Φ82)

Caster Rotation

Area (Φ100)

Intake Hole For

AC Cable

Exhaust Hole

Additional

Stacker

(Option)

Standard

Stacker

Print Engine

With Controller

WARNING

Transit Pass

Unit Type156

(Option)

Inhaltsverzeichnis

Andere Ricoh Drucker Handbücher

Ricoh

Ricoh Aficio SG 3110SFNw Bedienungsanleitung

Ricoh

Ricoh Aficio 3228C Bedienungsanleitung

Ricoh

Ricoh Aficio SG 3110DN Bedienungsanleitung

Ricoh

Ricoh SP3 Bedienungsanleitung

Ricoh

Ricoh Aficio 2105 Montage- und Wartungsanleitung

Ricoh

Ricoh Aficio CL4000DN Bedienungsanleitung

Ricoh

Ricoh P C200W Bedienungsanleitung

Ricoh

Ricoh GXe3300N Bedienungsanleitung

Ricoh

Ricoh Aficio SP 4310N Bedienungsanleitung

Ricoh

Ricoh IM 2702 Bedienungsanleitung

Ricoh

Ricoh Aficio MP 4002 Bedienungsanleitung

Ricoh

Ricoh Pro C9200 Bedienungsanleitung

Ricoh

Ricoh Aficio SP 5200DN Montageanleitung

Ricoh

Ricoh Ri 1000X Bedienungsanleitung

Ricoh

Ricoh SP 200 Bedienungsanleitung

Ricoh

Ricoh C4500 Bedienungsanleitung

Ricoh

Ricoh InfoPrint 1754dn Bedienungsanleitung

Ricoh

Ricoh Aficio AP4510 Konfigurationshandbuch

Ricoh

Ricoh InfoPrint 1832 Bedienungsanleitung

Ricoh

Ricoh Aficio SP C320DN Montageanleitung

Ricoh

Ricoh PRO C7200 Bedienungsanleitung

Ricoh

Ricoh B082 Bedienungsanleitung

Ricoh

Ricoh Aficio GX e3300N Bedienungsanleitung

Ricoh

Ricoh Ko-P1 Service-Handbuch

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung