Ricoh Pro 8300 Series Installationsanleitung

6 Misfeed

CIP Training

Pro 8300 Series

CIP Training 8300 Series

Misfeed

How do I clear a misfeed?

Locating Jammed Paper

If a misfeed occurs, remove the jammed paper by following the procedures indicated in the animation

that appears on the screen and the sticker or sheet inside the front cover.

A misfeed has occurred in the place corresponding to the letter displayed on the control panel.

Procedure for removing jammed paper

1. Remove the jammed paper by following the procedures that are displayed on the control panel.

2. When [Previous] or [Next] is displayed, press [Next] after completing a procedure.

When the jammed paper is removed, restore the device to the original state.

CIP Training 8300 Series

Misfeed

•Multiple paper misfeed locations may be indicated at the same time. When this happens, check

all the areas indicated.

•If there is no misfed paper in the area you check first, see the other areas that are indicated.

•If coated paper frequently becomes jammed and causes "U" to appear, contact your service

representative.

•If a paper misfeed occurs in Rb1 - Rb5, check whether any paper has been output on top of the

paper press of the finisher shift tray. If there is paper on top of the paper press, remove the

paper, and then remove the misfed paper from inside the finisher.

•When paper cannot be transferred to the post-processing side by turning the knob D1 as

instructed on the screen, see the position of the letter in the figure and turn the knob D1 in

reverse direction (clockwise) to send the paper back to the drawer unit, and then remove the

paper.

•After C is displayed and the drawer unit is pulled out to remove the jammed paper, check that

there is no toner searing on the location indicated in the figure. If toner smear is left, wipe off

the toner with a clean and dry cloth.

•If a paper jam occurs when using banner paper of 700.1 mm - 1260 mm (27.56 - 49.61 inches) in

length, open all guide plates along the feeding path in which the paper jam occurred and

remove the jammed paper.

CIP Training 8300 SeriesS

Misfeed

•(Note: Screenshots are provided for reference purpose only. Your display may vary depending on

your operating system and device.)

•Removing Jammed Paper

•Misfeed: When A is displayed

•Misfeed: When B is displayed

•Misfeed: When B1 is displayed

•Misfeed: When B2 is displayed

•Misfeed: When C is displayed

•Misfeed: When D1 is displayed

•Misfeed: When D2 is displayed

•Misfeed: When D3 is displayed

•Misfeed: When E is displayed

•Misfeed: When Kc1 - Kc9 is displayed

•Misfeed: When L is displayed

•Misfeed: When Mc is displayed

•Misfeed: When Mk is Displayed

•Misfeed: When N is Displayed

•Misfeed: When P is displayed

•Misfeed: When Q is displayed

•Misfeed: When R is displayed

•Misfeed: When Rb is displayed

•Misfeed: When Rt1 - Rt2 is displayed

•Misfeed: When U is displayed

•Misfeed: When V is displayed

•Misfeed: When Z1 is displayed

•Misfeed: When Z3 is displayed

Removing Jammed Paper

Removing jammed paper when the procedure is not displayed on the control panel

CIP Training 8300 Series

Misfeed

•When removing paper misfeeds, do not turn off the power. If you do, the configured

functions and values will be lost.

•To prevent paper misfeeds, do not leave any torn scraps of paper inside the device.

•If paper jams continue to occur, check the followings.

•Make sure there is nothing placed on the output tray.

•Make sure that the staple cartridge is set properly.

•Confirm the size and type of the paper you are using. For details, click the following link:

Paper size and type recommendations

•Confirm how to load paper in the following link: How to load paper

•Place the cut paper on a flat surface to prevent it from curling, and do not lean it against the

wall.

•Use paper that has been stored in the a room where the temperature is 20-25°C (68-77°F) and

the humidity is 30-65%.

•Make sure you set [Skew Detection] in [Machine: Image Position] under [Adjustment Settings

for Operators] in [Paper Settings] to [Off] when printing envelopes with a non-rectangular

flap.

•If misfeeds still occur frequently or the problem cannot be eliminated, contact your service

representative.

•When removing jammed paper, you can touch only those areas explicitly indicated in the

manual.

•Do not remove the fusing unit. Doing so will result in loss of print quality.

•To remove paper that has not been fed into the fixing section correctly, remove the jammed

paper through the underside of the fusing unit. If the jammed paper cannot be removed

through the underside of the fusing unit, remove it from the top.

•Inside the finisher, or inside the front cover, there are stickers or sheets explaining how to

remove misfed paper.

•If a detailed removal instruction appears on the right of the screen, follow it.

•You can also use the procedure indicated in the [Check Status] screen to remove jammed

paper.

•The inside of the device could be very hot. Do not touch the parts with a label indicating the

"hot surface." Otherwise, an injury might occur.

•Some of this device's internal components get very hot. For this reason, take care when

removing misfed paper. Not doing so could result in burns.

•Keep your hands clear of the booklet finisher tray when removing misfed paper, pulling out or

pushing in the finisher's staple unit. You can trap and injure your fingers if you do not.

•When removing jammed paper, make sure not to trap or injure your fingers.

•Keep your hands clear of the inside of the ring binder and the space under the ring binder

tray. You can trap your fingers if you do not.

CIP Training 8300 SeriesS

Misfeed A

Misfeed: When A is displayed

How do I clear a misfeed when A is displayed?

Follow the procedure below to remove the jammed paper.

1. Open the left and right front covers. 2. Lower lever A1, and then open the guide panel.

3. Turn knob A2 clockwise to remove the

misfed paper, and then check the LED

light is off.

4. If you cannot remove the misfed paper, turn

knob A3 clockwise. Remove the misfed paper,

and then check the LED light is off.

5. Raise lever A1 to its original position. 7. Close the front left and right covers.

CIP Training 8300 Series S

Misfeed B

1. Open the left and right front covers. 2. Turn the lever C1 to the left and lever

C2 to the right.

Misfeed: When B is displayed

How do I clear a misfeed when B is displayed?

Follow the procedure below to remove the jammed paper.

3. Pull out the unit. 4. Turn the knobs B4 and B5

counterclockwise at the same time.

5.. Remove the misfed paper, and

close the cover.

6.. Open the cover B7, and then check

there is no misfed paper in the unit.

7. Close the cover B7. 8. Slide the unit to its original position.

CIP Training 8300 Series S

Misfeed B

8. Raise the lever C1 and C2 to their original

positions.

Misfeed: When B1 is displayed

9. Close the front left and right covers of

the main unit.

3. Check the LED light is off. 4 .Turn the lever C1 to the left and lever

C2 to the right.

5. Pull out the unit. 6. Lower the knob B3.

1. Open the left and right front covers. 2. Turn the knob B1 and B2

counterclockwise at the same time.

CIP Training 8300 SeriesS

Misfeed B1

9. Slide the unit to its original position. 10. Raise the lever C1 and C2 to their

original positions.

7. Remove the misfed paper. 8. Raise the knob B3 to its original position.

11. Close the front left and right covers

of the main unit.

Andere Handbücher für Pro 8300 Series

Inhaltsverzeichnis

Andere Ricoh Drucker Handbücher

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Ricoh

Ricoh SP 220NW Bedienungsanleitung

Ricoh

Ricoh Aficio CL3000 Handbuch

Ricoh

Ricoh SP C250DN Bedienungsanleitung

Ricoh

Ricoh Aficio SP C820DN Bedienungsanleitung

Ricoh

Ricoh SH-P1 M020 Kurzanleitung

Ricoh

Ricoh Ri 100 Bedienungsanleitung

Ricoh

Ricoh C7528 Bedienungsanleitung

Ricoh

Ricoh 403079 - Aficio SP C410DN-KP Color Laser... Bedienungsanleitung

Ricoh

Ricoh Pro C7100s Bedienungsanleitung

Ricoh

Ricoh Aficio GX3000N Bedienungsanleitung

Ricoh

Ricoh Aficio SP C311N Bedienungsanleitung

Ricoh

Ricoh SP C250SF Bedienungsanleitung

Ricoh

Ricoh Pro C9500 Einrichtungshandbuch

Ricoh

Ricoh Aficio SP C242DN Montageanleitung

Ricoh

Ricoh Ri 100 Bedienungsanleitung

Ricoh

Ricoh D683 Kurzanleitung

Ricoh

Ricoh AP410 Bedienungsanleitung

Ricoh

Ricoh P 501 Bedienungsanleitung

Ricoh

Ricoh Aficio SP 1210N Bedienungsanleitung

Ricoh

Ricoh InfoPrint 1612 Bedienungsanleitung

Ricoh

Ricoh SP 213Nw Bedienungsanleitung

Ricoh

Ricoh AficioSP C410DN Bedienungsanleitung

Ricoh

Ricoh fax4700l Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung