Riello GITRE Bedienungsanleitung

cod. 20112452 rev. 0 02/2016

GITRÈ GITRÈ B/100

GITRÈ

EN USER MANUAL

Dear Customer,

Thank you for preferring a Rheating unit, a modern,

high-quality product that is able to guarantee your maximum

well-being for a long period of time, with high levels of relia-

bility and safety. In particular, if working together with a Tech-

nical Assistance Service R that is specically prepared and

trained to perform periodic maintenance, your unit will remain

at maximum efciency levels at minimum operating costs and if

required, replacements with original spare parts can be made.

This instruction manual contains important instructions and

precautions that must be observed to ensure the trouble-free

installation and efcient functioning of your GITRÈ boiler.

Please accept our renewed thanks for your purchase.

Riello S.p.A.

CONFORMITY

GITRÈ boilers conform to the following directives:

−Directive 92/42/EEC on efciency requirements

−Electromagnetic Compatibility Directive 2004/108/EC

−Low Voltage Directive 2006/95/EC

−Ecodesign Directive 2009/125/CE for energy-related prod-

ucts

−Energy Labelling Directive 2010/30/EU

−Delegated Regulation (EU) N. 811/2013

−Delegated Regulation (EU) N. 813/2013

−Delegated Regulation (EU) N. 814/2013

9 This product must only be used for the purpose for which it

is designed and made, as specied by R. Rdeclines

all responsibility, contractual or other, for damage to prop-

erty or injury to persons or animals caused by improper in-

stallation, adjustment, maintenance or use.

ENGLISH

This manual, Code 20112452 - Rev. 0 (02/2016)

comprises 16 pages.

CONTENTS

The following symbols are used in this manual:

9 CAUTION! = Identies actions that require caution and

adequate preparation.

0 STOP! = Identies actions that you MUST NOT do.

This manual, Code

- Rev.

comprises

pages.

1 GENERAL INFORMATION ............................4

1.1 General Safety Information ......................4

1.2 Precautions ..................................4

1.3 Description of the appliance .....................5

1.4 Safety devices ................................5

1.5 System layout.................................5

1.6 Control panel .................................7

2 USE.................................................9

2.1 Putting into service ............................9

2.1.1 Preliminary operations..........................9

2.1.2 Start-up.....................................9

2.1.3 Ignition failure ............................... 10

2.1.4 Resetting the burner and safety thermostat......... 10

2.2 Temporary shutdown...........................11

2.3 Preparing for extended periods of disuse........... 12

2.4 Cleaning and servicing the boiler ................. 12

2.5 External cleaning ............................. 12

2.5.1 Annual cleaning.............................. 12

2.6 Troubleshooting .............................. 13

3 RECYCLING AND DISPOSAL ........................14

GENERAL INFORMATION

1 GENERAL INFORMATION

1.1 General Safety Information

9 This product must be installed by a legally qualied heat-

ing engineer. On completion of the installation, the install-

er must issue the owner with a declaration of conformity

conrming that the installation has been completed to the

highest standards in compliance with the instructions pro-

vided by Rin this instruction manual, and that it con-

forms to all applicable laws and standards.

9 This product must only be used for the purpose for which it

is designed and made, as specied by R. Rdeclines

all responsibility, contractual or other, for damage to prop-

erty or injury to persons or animals caused by improper in-

stallation, adjustment, maintenance or use.

9 The room where the boiler is installed must be proper-

ly ventilated to ensure a sufcient supply of air for correct

combustion.

9 If you notice any water leaks, disconnect the boiler from the

mains electricity supply and shut off the water supply.

9 The boiler must be serviced at least once a year.

9 Periodically check that pressure in the central heating cir-

cuit, when cold, is approximately 1.5 bar and below the

maximum limit specied for the boiler. If necessary, top up

through the lling cock or contact the RTechnical Assis-

tance Service or a qualied heating engineer.

9 If the boiler is not going to be used for an extended peri-

od of time, perform the operations described later in this

manual.

9 This manual is an integral part of the equipment and there-

fore must be stored carefully and must ALWAYS accompany

the boiler even if it is sold to another Owner or User or trans-

ferred to another plant. If it is damaged or lost, request an-

other copy from your local Technical Assistance Service R.

1.2 Precautions

The operation of any appliance that uses fuel, electrical power

and water demands that a number of fundamental safety pre-

cautions be respected:

0 Do not allow children or inrm persons to operate the sys-

tem unsupervised.

0 It is forbidden to use electrical devices or equipment, such

as switches, appliances, etc. if there is a smell of gas or un-

burnt products. If so:

−Ventilate the room, opening doors and windows

−Close the fuel shut-off cock.

0 Do not touch the boiler while barefoot or wet.

0 Never clean or service the boiler without rst disconnect-

ing it from the mains electricity supply by turning the mains

power switch and the control panel switch OFF.

0 Never pull, disconnect, or twist the electrical cables coming

from the appliance even if it is disconnected from the mains

electricity supply.

0 Do not obstruct or restrict the vents in the room where the

boiler is installed. Adequate ventilation is essential for cor-

rect combustion.

0 Do not expose the boiler to the elements. It is not designed

for use outdoors.

0 It is prohibited to leave inammable substances and con-

tainers in the room where the boiler is installed.

0 Do not dispose of packaging material into the environment,

or leave it within the reach of children, since it can become

a potential hazard. Dispose of packaging material in com-

pliance with applicable legislation.

0 It is forbidden to operate the boiler without water.

GENERAL INFORMATION

1.3 Description of the appliance

The GITRÈ boiler is an oil fuelled hot water boiler capable of low

temperature functioning. GITRÈ versions are designed only for

central heating applications. The GITRÈ B/100 version is equipped

with a 100 litre vitried storage cylinder and can be used for

central heating and domestic hot water production.

The cast iron boiler body features a triple ue pass design and a

horizontal combustion chamber.

The front cover opens fully to facilitate the inspection, mainte-

nance and cleaning of internal parts and to minimise service

time.

The boiler body is covered in high density glass wool insulation

to reduce heat loss.

The boiler is tted with a single stage oil burner.

The GITRÈ boiler's control logic incorporates a total shutdown

function to minimise energy consumption:

−The GITRÈ (heating only) model only starts up if the cen-

tral heating system requests heat (i.e. when the room

thermostat switches the heating on);

−If the GITRÈ B/100 (heating and DHW) model is in "Sum-

mer" mode ("Summer/Winter" selector turned to Sum-

mer position), it only starts up to restore the setpoint

temperature of the water in the storage cylinder. If it is

in "Winter" mode ("Summer/Winter" selector turned to

Winter position), it starts up either in response to a re-

quest for heat from the heating system (i.e. when the

room thermostat switches the heating on) or to restore

the setpoint temperature of the water in the storage

cylinder (DHW heat requests are prioritised over central

heating requests)..

1.4 Safety devices

GITRÈ boilers incorporate the following safety and control de-

vices:

−A manual reset safety thermostat that forces a safe-

ty shutdown if boiler temperature exceeds the safety

threshold (110°C). The sensor used to monitor this tem-

perature is located on the body of the heat exchanger;

−A minimum temperature thermostat that enables the

central heating pump only if boiler temperature exceeds

the minimum permissible (50°C);

−An electronic burner controller that monitors the correct

functioning of the selected burner program and sends

a lockout signal to the control panel in the event of an

error.

ONLY FOR GITRÈ B/100 MODELS

−A maximum temperature thermostat that shuts down

the burner if boiler temperature reaches or exceeds the

default maximum limit ( 82°C) during the heating of do-

mestic hot water in the storage tank;

−A heat dissipation thermostat that starts up the storage

tank pump to dissipate excess heat in order to keep boil-

er temperature below the safety threshold (90°C).

9 The intervention of a safety device indicates a potentially

dangerous malfunction in the system. Contact the manu-

facturer’s Technical Assistance Service immediately.

9 Safety devices must only be replaced by the manufacturer's

Technical Assistance Service using original spare parts. Refer

to the spare parts catalogue supplied with the boiler.

0 Do not use the boiler if any of its safety devices are faulty.

1.5 System layout

GITRÈ

1 Burner

2 Boiler body

3 Control panel

4 Sensor socket

5 Lifting holes

6 Flue gas exhaust tting

7 Casing

8 Drain cock

GENERAL INFORMATION

GITRÈ B/100

1 Control panel

2 Storage cylinder drain cock

3 CH circuit drain cock

4 Automatic vent valve

5 Storage cylinder

6 Casing

7 Non-return valve

8 Boiler circulator

9 Boiler temperature sensor socket

10 Lifting holes

11 Burner

12 Boiler body

13 Flue gas exhaust tting

14 Domestic cold water inlet

15 DHW circulation

16 Storage cylinder temperature sensor socket

17 DHW outlet

18 Magnesium anode

GENERAL INFORMATION

1.6 Control panel

GITRÈ

100

0120

1 Function selector

0 Off

IOn

II Burner reset

2 Boiler temperature gauge

Displays the temperature of the central heating water

3 Boiler thermostat

Allows you to set the temperature of the central heating water (setting range 55-82°C)

4 Electrical power indicator (green)

Lights to show that the boiler is receiving electrical power

5 Burner lockout indicator (red)

Lights to show that the burner locked out

6 Manual reset for safety thermostat

Allows you to reset the boiler if the safety thermostat trips. Unscrew the protective cover to access

the reset button

7 Protective cover over control panel

GENERAL INFORMATION

GITRÈ B/100

100

0120

100

0120

1 Function selector

0 Off

IOn

II Burner reset

2 Boiler temperature gauge

Displays the temperature of the central heating water

3 Boiler thermostat

Allows you to set the temperature of the central heating water (setting range 55-82°C)

4 Electrical power indicator (green)

Lights to show that the boiler is receiving electrical power

5 Burner lockout indicator (red)

Lights to show that the burner locked out

6 Summer (I) / Winter (II) selector

7 Storage cylinder temperature gauge

Displays the temperature of the domestic hot water in the storage cylinder

8 Manual reset for safety thermostat

Allows you to reset the boiler if the safety thermostat trips. Unscrew the protective cover to access

the reset button

9 Storage cylinder thermostat

Allows you to set the temperature of the domestic hot water (setting range 0-70°C)

10 Protective cover over control panel

USE

2 USE

2.1 Putting into service

Have the RTechnical Assistance Service start-up your GITRÈ

boiler for the rst time. Once this has been done, the boiler can

be left to function automatically.

Under certain circumstances, such as after long periods of dis-

use, the user may need to re-start it without involving the Tech-

nical Assistance Service.

2.1.1 Preliminary operations

Perform the following checks before starting up the boiler:

−Check that the fuel shut-off cock and heating system

shut-off cock are open

−Check that the central heating circuit pressure gauge

shows a pressure over 1 bar with the system cold. Check

also that the circuit is properly de-aerated

2.1.2 Start-up

Once you have completed all the checks listed above, proceed as

follows to start up the boiler for the rst time:

ONLY FOR MODELS GITRÈ 4-GITRÈ 5-GITRÈ 6

−Turn the boiler’s mains power switch ON

−Set the room thermostat to the required temperature (~

20°C) or, if the system has a timer or timer-thermostat,

make sure that this is switched “ON” and adjusted to the

required temperature (~ 20°C).;

−Open the control panel access door;

ONLY FOR MODELS GITRÈ 4-GITRÈ 5-GITRÈ 6

−Turn the boiler thermostat to about the middle of the

section with three lines;

100

0120

−Turn the function selector to ON (I) and make sure that

the green power indicator lights.

NOTE in the case of GITRÈ 4 models, the burner only starts up

at the end of the fuel oil pre-heating phase.

100

0120

The boiler now starts up and the burner remains lit until the

temperature setpoint is reached.

ONLY FOR GITRÈ B/100 MODELS

−Turn the boiler’s mains power switch ON;

USE

−Set the room thermostat to the required temperature (~

20°C) or, if the system has a timer or timer-thermostat,

make sure that this is switched “ON” and adjusted to the

required temperature (~ 20°C).;

−Open the control panel access door;

−Adjust the boiler and storage cylinder thermostats to

about the middle of the section with three lines;

−Turn the Summer/Winter selector to (II) Winter;

100

0120

100

0120

−turn the function selector to (I) ON and make sure that

the green power indicator lights.

100

0120

The boiler now starts up and the burner remains lit until the

temperature setpoint is reached.

2.1.3 Ignition failure

If any ignition errors or malfunctions occur, the burner enters

“LOCKOUT”. This is shown by the red button light on the burner

and by the warning light on the control panel.

100

0120

9 If a “LOCKOUT SHUTDOWN” occurs, wait about 30 seconds be-

fore resetting the burner.

2.1.4 Resetting the burner and safety thermostat

To restore normal startup conditions, open the protective cover

over the control panel and turn the function selector to posi-

tion (II) "Reset burner" for at least 1 second before returning it to

position (I). Wait for the burner to complete the entire ignition

cycle again, up to the ignition of the ame.

100

0120

If boiler temperature becomes too high, the manual reset safety

thermostat trips.

9 No warning signal is given if the safety thermostat trips, but

the fact that is has tripped can be seen from the boiler tem-

perature gauge (T>110°C).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Riello Kessel Handbücher

Riello

Riello Family KIS Series Bedienungs- und Installationshandbuch

Riello

Riello Residence Externa Condens KIS i Bedienungsanleitung

Riello

Riello RESIDENCE COLONNA CONDENS SOLAR KV/200 - 30... Handbuch

Riello

Riello Caldariello Condens 25 KIS Bedienungs- und Installationshandbuch

Riello

Riello VOKERA Mynute i20 Bedienungsanleitung

Riello

Riello Condexa HPR 35 Benutzerhandbuch

Riello

Riello Caldariello Condens 25 KIS Bedienungs- und Installationshandbuch

Riello

Riello Residence Condens i Bedienungsanleitung

Riello

Riello Start Aqua Condens 25/60 BIS Bedienungs- und Installationshandbuch

Riello

Riello FAMILY AQUA CONDENS 3.5 BIS Bedienungs- und Installationshandbuch

Riello

Riello RTQ 109 Betriebsanleitung

Riello

Riello Family IS Bedienungs- und Installationshandbuch

Riello

Riello INSIEME EVOe 25 B/70 LN Bedienungsanleitung

Riello

Riello RTT 163 Bedienungsanleitung

Riello

Riello Vokera UNICA MAX Series Bedienungsanleitung

Riello

Riello VOKERA VISION PLUS Series Bedienungsanleitung

Riello

Riello Residence Colonna Condens KV 130-30 ISC Bedienungsanleitung

Riello

Riello ALUDOMUS SOLAR KV/200 20 ISC SOLAR Handbuch

Riello

Riello Vokera VERVE i 50 Versionshinweis

Riello

Riello INSIEME CONDENS 26 B Bedienungsanleitung

Riello

Riello TAU 1750 N Service-Handbuch

Riello

Riello INSIEME EVO COND 25 B/130 LN Handbuch

Riello

Riello RTS 3S Betriebsanleitung

Riello

Riello TAU UNIT OIL 35 B Bedienungsanleitung

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung