Rigol DP700 Series Bedienungsanleitung

English

Quick Guide

DP700 Series Programmable

Linear DC Power Supply

Mar. 2016

RIGOL TECHNOLOGIES, INC.

RIGOL

DP700 Quick Guide 1

English

Guaranty and Declaration

Trademark Information

RIGOL is a registered trademark of RIGOL TECHNOLOGIES, INC.

Publication Number

QGH05101-1110

Notices

RIGOL products are covered by P.R.C. and foreign patents, issued and

pending.

RIGOL reserves the right to modify or change parts of or all the

specifications and pricing policies at the company’s sole decision.

Information in this publication replaces all previously released materials.

Information in this publication is subject to change without notice.

RIGOL shall not be liable for either incidental or consequential losses in

connection with the furnishing, use, or performance of this manual, as

well as any information contained.

Any part of this document is forbidden to be copied, photocopied, or

rearranged without prior written approval of RIGOL.

Product Certification

RIGOL guarantees that this product conforms to the national and industrial

standards in China as well as the ISO9001:2008 standard and the

ISO14001:2004 standard. Other international standard conformance

certifications are in progress.

If you have any problem or requirement when using our products or this

manual, please contact RIGOL.

E-mail: [email protected]

Website: www.rigol.com

RIGOL

2 DP700 Quick Guide

English

General Safety Summary

1. Only the exclusive power cord

designed for the instrument

and authorized for use within

the local country could be

used.

2. Ensure that the instrument is

safely grounded.

3. Observe all terminal ratings.

4. Use proper overvoltage

protection.

5. Do not operate without covers.

6. Do not insert objects into the

air outlet.

7. Use the proper fuse.

8. Avoid circuit or wire exposure.

9. Do not operate the instrument

with suspected failures.

10. Provide adequate ventilation.

11. Do not operate in wet conditions.

12. Do not operate in an explosive

atmosphere.

13. Keep instrument surfaces clean

and dry.

14. Prevent electrostatic impact.

15. Handle with caution.

16. Do not use this instrument to

provide power for the active load.

Safety Notices and Symbols

Safety Notices in this Manual:

WARNING

Indicates a potentially hazardous situation or practice which, if not

avoided, will result in serious injury or death.

CAUTION

Indicates a potentially hazardous situation or practice which, if not

avoided, could result in damage to the product or loss of

important data.

Safety Terms on the Product:

DANGER

It calls attention to an operation, if not correctly performed,

could result in injury or hazard immediately.

WARNING

It calls attention to an operation, if not correctly performed,

could result in potential injury or hazard.

CAUTION

It calls attention to an operation, if not correctly performed,

could result in damage to the product or other devices

connected to the product.

RIGOL

DP700 Quick Guide 3

English

Safety Symbols on the Product:

Hazardous

Voltage

Safety

Warning

Protective Earth

Terminal

Chassis Ground

Test Ground

Care and Cleaning

Care

Do not store or leave the instrument where it may be exposed to direct sunlight

for long periods of time.

Cleaning

Clean the instrument regularly according to its operating conditions.

1. Disconnect the instrument from all power sources.

2. Clean the external surfaces of the instrument with a soft cloth dampened

with mild detergent or water. When cleaning the LCD, take care to avoid

scarifying it.

CAUTION

To avoid damage to the instrument, do not expose it to caustic

liquids.

WARNING

To avoid short-circuit resulting from moisture or personal injuries,

ensure that the instrument is completely dry before connecting it

to the power supply.

RIGOL

4 DP700 Quick Guide

English

Document Overview

This manual introduces some basic information that you should know when you

use the DP700 series power supply for the first time. It contains the following

contents: out-of-box inspection method, product overview, how to connect the

instrument to the AC power, procedures for carrying out the power-on

inspection and output inspection, as well as remote control overview.

Tip

For the latest version of this manual, download it from RIGOL official

website (www.rigol.com).

Format Conventions in this Manual

Key

(1) The key on the front panel is denoted by the format of "Key Name (Bold)

+ Text Box" in the manual. For example, On/Off denotes the "On/Off"

key.

(2) Use the screen shot to indicate the key. For example, denotes the

Power key.

Content Conventions in this Manual

DP700 series programmable linear DC power supply includes the following

models. Unless otherwise specified, this manual takes DP711 as an example to

illustrate DP700 series power supply and its basic operation.

Model

No. of Channels

Output Voltage/Current

DP711

30 V/5 A

DP712

50 V/3 A

RIGOL

DP700 Quick Guide 5

English

General Inspection

1．Inspect the packaging

If the packaging has been damaged, do not dispose the damaged

packaging or cushioning materials until the shipment has been checked

for completeness and has passed both electrical and mechanical tests.

The consigner or carrier shall be liable for the damage to the instrument

resulting from shipment. RIGOL would not be responsible for free

maintenance/rework or replacement of the instrument.

2．Inspect the instrument

In case of any mechanical damage, missing parts, or failure in passing the

electrical and mechanical tests, contact your RIGOL sales

representative.

3．Check the accessories

Please check the accessories according to the packing lists. If the

accessories are damaged or incomplete, please contact your RIGOL

sales representative.

RIGOL

6 DP700 Quick Guide

English

Product Overview

DP700 series power supply is a type of affordable programmable linear DC

power supply with high performance. With superb performance specifications,

pure and reliable output, and clear user interface, the DP700 series supports

timing output and trigger function, and provides a remote communication

interface, enabling you to meet your diversified test requirements.

For descriptions of the front panel, refer to Figure 1; for descriptions of the rear

panel, refer to Figure 2; and for descriptions of the main interface (display

screen), refer to Figure 3.

mA A

POWER

ON OFF 30V/5A

Number

1 2 3

4 5 6

7 8 9

Memory

System

Figure 1 Front Panel

1. LCD

2. Function Keys

3. Output On/Off Key

4. Power Key

5. Output Terminals

6. Arrow Keys and

Confirmation Key

7. Knob

8. Num Keys and

Return Key

RIGOL

DP700 Quick Guide 7

English

ACSELECTOR

100Vac 120Vac 220Vac 240Vac

100V T5A

120V 250Vac

220V T2.5A

240V 250Vac

FUSE RATING

RIGOL TECHNOLOGIES,INC.

MADEINCHINA

Figure 2 Rear Panel

Note: Pin 7 and Pin 8 of the RS232 interface are not used in remote communication. They are

used in the trigger function (optional).

Figure 3 Main Interface

4. Output Setting

2. Actual Output

Status

5. System Status Icons

3. Help Information

1. Actual Output Mode

1. Input Power

Requirement

2. AC Power Supply

Connector

3. RS232 Interface

6. Fuse Rating

5. Fuse Cap

4. Air Outlet

7. AC Selector

RIGOL

8 DP700 Quick Guide

English

Power-on Inspection

DP700 series power supply supports various specifications of AC input power.

When the DP700 series is connected with different AC power supplies, the AC

selector setting on the rear panel of the instrument is different, as shown in the

table below.

Table 1 AC Input Power Specification and AC Selector Setting

AC Input Power

AC Selector

100 Vac x (100% ± 10%), 50 Hz to 60 Hz

100Vac

120 Vac x (100% ± 10%), 50 Hz to 60 Hz

120Vac

120 Vac x (100% ± 10%), 50 Hz to 60 Hz

220Vac

240 Vac x (100% ± 10%) (max: 253 Vac), 50 Hz to 60 Hz

240Vac

Please strictly follow the steps below to connect the instrument to the power

supply, and perform the power-on inspection and output inspection.

1．Check the input power

Ensure that the AC power to be connected to the instrument conforms to

the AC input power requirement specified in Table 1.

2．Check the AC selector

Ensure that the AC selector setting on the rear panel of the instrument

matches with the actual AC input power (refer to Table 1).

3．Check the fuse

When leaving the factory, the instrument has installed a fuse that

conforms to the local standard. When the input voltage is 100 Vac or 120

Vac, Fuse T5A is used; when the input voltage is 220 Vac or 240 Vac, Fuse

T2.5A is used.

4．Connect the AC power

Plug the specified power cord available in the accessories into the AC

power supply connector of the instrument, and then connect the

instrument to the properly grounded AC power.

WARNING

To avoid electric shock, ensure that the instrument is correctly

grounded.

RIGOL

DP700 Quick Guide 9

English

5．Power on the instrument

Press the Power key , and then the instrument is launched and

begins to perform the self-inspection. If the instrument passes the

self-inspection, the welcome interface is displayed; otherwise,

self-inspection failure information about corresponding items (including

the analog board, OVP, OCP, fan, and temperature) will be displayed.

Tip

After powering off the instrument, please wait for at least 2 s to power

it on again.

6．Perform the output check

Perform the output check to ensure that the power supply can output the

rated values and properly respond to the operations on the front panel.

Note: Before checking the current output, you should complete the

voltage output check first.

Check the voltage output: verify the basic voltage functions without a

load.

(1) Press to power off the instrument.

(2) Ensure that no load is connected to the channel output terminals on

the front panel. Then, press to power on the instrument, and

check whether the voltage between the positive terminal (+) and

negative terminal (-) of the channel output is 0 V.

(3) Press On/Off to turn on the channel output.

At this time, the actual output status (actual

output voltage (V), actual output current (A),

and actual output power (W)) on the left

section of the interface is highlighted, and the

actual output mode (CV) is displayed.

(4) Set the output voltage to 0 V (For setting methods, refer to the

descriptions of the help information below the interface or

descriptions on Page 11.), and check whether the actual output

voltage displayed on the left section of the interface is approximately

0 V, the actual output current approximately 0 A. Set the output

voltage to 30 V (max. rating value), and check whether the actual

Andere Handbücher für DP700 Series

Inhaltsverzeichnis

Andere Rigol Stromversorgung Handbücher

Rigol

Rigol DP900 Series Bedienungsanleitung

Rigol

Rigol DP932A Bedienungsanleitung

Rigol

Rigol DP800A Series Bedienungsanleitung

Rigol

Rigol DP800 Series Gebrauchs- und Pflegehandbuch

Rigol

Rigol DP1116A Bedienungsanleitung

Rigol

Rigol DP832 Bedienungsanleitung

Rigol

Rigol DP1308A Bedienungsanleitung

Rigol

Rigol DP700 Series Gebrauchs- und Pflegehandbuch

Rigol

Rigol DP800A Series Bedienungsanleitung

Rigol

Rigol DP800 Series Gebrauchs- und Pflegehandbuch

Rigol

Rigol DP800 Series Kurzanleitung

Rigol

Rigol DP900 Series Betriebsanleitung

Rigol

Rigol DP800 Series Betriebsanleitung

Rigol

Rigol DP1308A Installations- und Betriebshandbuch

Rigol

Rigol DP831 Bedienungsanleitung

Rigol

Rigol DP1308A Bedienungsanleitung

Rigol

Rigol DP900 Series Bedienungsanleitung

Rigol

Rigol DP2000 Series Betriebsanleitung

Rigol

Rigol DP800 Series Bedienungsanleitung

Rigol

Rigol DP1116A Installations- und Betriebshandbuch

Rigol

Rigol DP800 Series Bedienungsanleitung

Rigol

Rigol DP700 Series Bedienungsanleitung

Rigol

Rigol DP800A Series Bedienungsanleitung

Rigol

Rigol DP2000 Series Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung