Rioworks SDRCB Bedienungsanleitung
Overview
Hard ware
Installation
BIOS
Setup
BIOS Flash
Utility
Troubleshooting
SDRCB
User’s Guide
The information in this document is subject to change without notice
Arima Computer Corp. makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose.
Arima Computer Corp. shall not be liable for errors contained herein or for
incidental or consequential damages in connection with the furnishing,
performance, or use of this material.
Arima Computer Corp. assumes no responsibility for the use or reliability of
its software on equipment that is not furnished by Arima Computer Corp.
This document contains proprietary information that is protected by
copyright. All rights are reserved. No part of this publication may be
reproduced, transcribed, stored in a retrieval system, translated into any
language or computer language, or transmitted in any form whatsoever
without the prior written consent of Arima Computer Corp.
Copyright2000by Arima Computer Corp.All rights reserved.
RIOWORKSTM is the trademark of Arima Computer Corp.
Other products and companies referred to herein the trademarks or
registered trademarks of their respective companies or mark holders.
Printed in Taiwan
Revision Version: 1.00
Release Date: September 2000
Contents
OVERVIEW:............................................................................. I
UNPACKING..................................................................................I
FEATURES HIGHLIGHT...................................................................II
ABOUT THIS USER GUIDE.............................................................VI
GETTING HELP........................................................................... VII
SDRCB MOTHERBOARD (PICTURE)..............................................VIII
SDRCB MOTHERBOARD (LAYOUT)................................................IX
CHAPTER 1:HARDWARE INSTALLATION....................1-1
Step 1:Jumper Setting ..........................................................1-2
Step 2:Install Memory...........................................................1-5
Step 3:Install CPU................................................................1-9
Step 4:Attach Cable to Connectors......................................1-11
Step 5:Install Expansion Cards............................................1-28
Step 6:Powering on Your Computer.....................................1-29
CHAPTER 2:BIOS SETUP.................................................2-1
Section 1:Setup Categories...................................................2-5
Section 2:Main Menu............................................................2-9
Section 3:Advanced Menu..................................................2-11
3-1:SUPER IO CONFIGURATION............................................2-11
3-2:IDE CONFIGURATION....................................................2-15
3-3:FLOPPY CONFIGURATION ...............................................2-19
3-4:BOOT CONFIGURATION..................................................2-20
3-5:EVENT LOG CONFIGURATION...........................................2-23
3-6:SYSTEM HEALTH MONITORING HARDWARE.......................2-24
Section 4:Chipset Menu......................................................2-30
Section 5:PCI PnP..............................................................2-35
Section 6:Power.................................................................2-38
Section 7:Boot....................................................................2-42
Section 8:Security..............................................................2-46
Section 9:Exit.....................................................................2-49
CHAPTER 3:BIOS FLASH UPGRADE UTILITY............3-1
APPENDIX A:TROUBLESHOOTING.............................. A-1
APPENDIX B:SYMPTOM REPORT FORM................... A-5
i
Overview
Overview
Overview
Thank you for choosingthe RIOWORKSTM SDRCB high performance Server
motherboard. TheSDRCB is adual Socket-370motherboard (M/B) based on
the ATX form factor. As the latest ServerWorks LE chipset is built in the M/B,
SDRCB fully supportsIntel®500MHz-1GMHz+PIII/Coppermine FC-PGA
processor at 100/133 MHz FSB (Front Side Bus) frequency.In memory
support, SDRCB provides four sockets for the system memory.Usersjust
simply choose PC100/133,registered with ECC DIMMs as the system
memory and the total maximum memory size can be up to 4GB.Flexibility
and expandability are always concerned by RIOWORKSTM, SDRCB contains
three 32bit/33Mhz and three 64bit/66MHz PCI slots for numerous add-on
cards and provides Peer PCI transaction support to increasesystem
performance.
Other features such as onboard SCSI interface (Optional), onboard Intel®
82559 10/100 MbpsLAN port (Optional)and onboard VGAwill provide high
system capabilities thatmeet a wide range of demanding Sever applications.
Unpacking
Remove all items from the box and make sure you have these following
items:
rOne RIOWORKS SDRCB motherboard
rOne ATA /33 IDE ribbon cable
rOne 68-pin(female) SCSI cable (Optional)
rOne 50-pin SCSI cable (female) (Optional)
rOne Floppy ribbon cable
rOne bag of spare jumpers
rOne SDRCB User’s Guide
rOne CD containing drivers and utilities
rOne Onboard SCSIand LAN User’s Guide (Optional)
rDriver Disk(s) for onboard SCSI (Optional)
If you discover damaged or missing items, please contact your retailer.
ii
Overview
Overview
Features Highlight
CPU Support dual Intel
®
500MHz~1GHz+PIII/Coppermine
FC-PGA CPUs at 100/133 MHz Front Side Bus (FSB)
frequency and designed for Socket-370 technology.
Chipset Use the latest ServerWorks LE chipset in the SDRCB
M/B. As known, the LE chipset architecture is
consisted of two main components: The Champ North
Bridge (CNB30LE) and Open South Bridge
TM
(OSB4).
Because the powerful features of its components, it
can fully support the newest technologies:
64bit/66MHz PCI bus, 100/133 FSB frequency, USB
interface, Peer PCI Transaction and I
2
C Bus support
andsoon.
System
Memory
Support
SDRCB provides four DIMM sockets and supported
total systemmemory size can be from 128MB to 4GB.
A user just chooses specific PC133/100, registered
with ECC DIMMs and DIMMs support
64Mbit/128Mbit/256Mbit technology that will allow up
to 128/256/512Mbyte per two row (Double sided
DIMM) as the system memory. Please also refer to the
install memory section (Page 1-3) for further detailed
information. Also please refer to the RIOWORKS
Website for the latest memory AVL.
Expansion
Slots Contain three 32-bit PCI, three 64-bit PCI expansion
slots for 64-bit/32-bit 66MHz/33MHz add-on card. The
advantage from 64-bit/66MHz PCI technology is the
theoretical bandwidth can be up to 528MB/s. Besides
this, SDRCB also supportsPeer PCI transaction. A
PCI device on the 32bit/33MHz PCI bus can do
Memory and I/O cycles to a PCI device on the
64bit/66MHz PCI bus
iii
Overview
Overview
Onboard
VGA Chip Use ATI RAGE
TM
as the onboard VGA chip to deliver
superior 3D acceleration and comprehensive 3D
support. The features of VGA chip include a 1.2 million
triangle/S Setup engine, single-pass trilinear filtering,
six perspectively correct texturing modes, video
texturing, Gouraud and specular shading and a host of
3D special effects. As it also incorporates all the
required logic to interface gluelessly with Digital Flat
Panel monitor, it provide the lowest cost DFT ready
implementation while maintaining support for existing
VGA connector for legacy monitor support.
Onboard
SCSI
(Optional)
Use SYMBIOS 1010-66 Ultra160 chip as the onboard
SCSI controller of SDRCB. As known, SYMBIOS
1010-66 is a high performance, dual-channel,
64bit/66MHz and Ultra160 SCSI controller. It is able to
provide theoretical 160MB/s data transfer rate per
channel (320MB/s total). It is fully backward
compatible with all of the SCSI standards such as
Ultra, Ultra Wide, and Ultra2. In order to provide
flexibility and expandability, SDRCB provides three
common SCSI internal connectors for the SCSI
devices: one is “SCSI Ultra3-50 for ultra SCSI devices;
two connectors are “ULTRA3 SCSI” for Ultra160 SCSI
devices.
Onboard LAN
(Optional) Use Intel® 82559 Fast Ethernet Multifunction controller
as onboard network interface controller. Intel
®
82559
fast Ethernet Controller can provide IEEE
802.3/802.3u 10 Base-T and 100 Base-TX compatible
network environment. A user can achieve advanced
manageability of the Alert on LAN II Specification by
using thisIntel® 82559 chip.
iv
Overview
Overview
Super Multi-
I/O Provides ports and one parallel port with EPP and
ECP capabilities. UART2 two high-speed UART
compatible serial can also be directed from COM2 to
the Infrared Module for wireless connections.
Ultra DMA 33
Bus Master
IDE
Comes with an onboard PCI Bus Master IDE
controller with one connector that support two IDE
devices inone channels, supports Ultra DMA 33, PIO
Mode 3 and 4 and Bus Master IDE DMA Mode 4, and
supports Enhanced IDE devices.
Intelligent
Platform
Manage
Interface
SDRCB provides one IPMI feature connector for the
system management add-on card that is able to
provide some system important information such as
system inventory, hardware health monitoring, and so
on in the in-band/out-of-band and cross–platform
environment.
Floppy Drive Supports 3.5” (1.44MB or 2.88MB) floppy drive and
Japanese standard “Floppy 3 mode”(3.5”disk drive:
1.44MB, 1.2MB, 720KB) and LS-120 floppy disk
drives (3.5”disk drive: 120 MB). BIOS supports IDE
CD-ROM boot-up.
Enhanced
ACPI Fully implements the ACPI standard for Windows
98/NT5.0/2000 compatibility, and supports soft off.
System
Management Supports Fan Status Monitoring and Alert,
Temperature Monitoring and Alert, Voltage Monitoring
and Alert, through the onboard Hardware Monitor, and
RIOWORKSTM’“SmartWatchTM” software.
v
Overview
Overview
Desktop
Management
Interface
(DMI)
Supports DMI through BIOS, which allows hardware to
communicate within a standard protocol creating a
higher level of compatibility.
PC99
Compliant The SDRCB is fully compliant with the Microsoft PC99
specification at both the hardware and BIOS levels.
VRM Support Support VRM 8.4 specification.
Dimension Extended ATX form factor-12’x13”
vi
Overview
Overview
About This User Guide
This manual explains how to build your system withSDRCB in detail. Please
follow the proceduresof this User Manualcarefully and pay special attention
to theseicons.
IMPORTANT This icon informs you for particularly important
details regarding the setup or maintenance of
your system. While we point out the most vital
paragraphs in a chapter, you should always
read every word carefully. Failing to do so can
cause exasperation.
WARNING This icon alerted you for potential dangers
during setting up your system with SDRCB.
These warnings should not be regarded as the
whole of your safety regimen. Never forget that
computer are electronic devices and are
capable of delivering a shock. Prevent damage
to yourself and to your board: always ensure
that your system is turned off and unplugged
the power cords whenever you are working
with it ,and that you are equipped
NOTE This icon alerted you for notice during setting
up your system. It provides you can usefulalert
during setting up a new system.
TIP This icon will show you how to configure your
system with SDRCB in aneasy and simple
ways. This icon always provides some useful
description to help you configure your system.
Inhaltsverzeichnis
Andere Rioworks Hauptplatine Handbücher
Rioworks
Rioworks PURCA Bedienungsanleitung
Rioworks
Rioworks TDVIA-L Bedienungsanleitung
Rioworks
Rioworks SDVIA Bedienungsanleitung
Rioworks
Rioworks SDVIA Bedienungsanleitung
Rioworks
Rioworks TDRCA Bedienungsanleitung
Rioworks
Rioworks SDVIA Bedienungsanleitung
Rioworks
Rioworks SDVIA-100 Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
