Ritron DoorCom Bedienungsanleitung

___________________________________________________________________________________________________________

Ritron Publication 14500083 Rev. A 06-12

DoorCom, Quick Talk and Liberty are trademarks of Ritron, Inc.

Call 800-USA-1-USA for the right Wireless Solutions to your communication needs.

P.O. Box 1998 •Carmel, Indiana 46082-1998 •USA

Phone: 317-846-1201; 800-USA-1-USA (800-872-1872) •Fax: 317-846-4978

Email: [email protected] •Website: www.ritron.com

Owner’s Manual

Basic Operation

RDC-SERIES DOORCOM™MODELS............................................i

SYSTEM COMPONENTS ............................................................1

OPTIONAL AND REPLACEMENT ACCESSORY EQUIPMENT...............1

BRIEF FEATURE OVERVIEW .......................................................1

CONTROLS,CONNECTORS AND BUTTONS ...................................2

Figure-1: RDC-1 and R-Series Radio, Controls and

Connectors ............................................................................2

INITIAL SET-UP AND PROGRAMMING ...........................................2

Programmable Features .........................................................3

Field Programming

HOW TO READOUT CURRENT RADIO FREQUENCY &TONE CODES.4

HOW TO FIELD PROGRAM FREQUENCY &TONE CODES................5

TABLE 1: PROGRAMMABLE FREQUENCY CODES....................... 6

CANADIAN FREQUENCY CODES................................ 6

TABLE 2: INTERFERENCE ELIMINATOR PROGRAMMABLE QC

TONE CODES .........................................................7

TABLE 3: INTERFERENCE ELIMINATOR PROGRAMMABLE DQC

TONE CODES .........................................................7

TABLE 4: ADVANCED FEATURE CODES ...................................7

TABLE 5: SINGLE DIGIT RADIO FEATURE CODES......................8

HOW TO FIELD PROGRAM RADIO FEATURE CODES ......................8

Installation Instructions

RDC-1 SPEAKER INTERCOM BOX INSTALLATION INSTRUCTIONS....9

Figure -2: RDC-1 INSTALLATION .............................................9

R-SERIES RADIO INSTALLATION INSTRUCTIONS ......................... 10

Figure -3: R-Series Radio Installation.................................10

Operating Instructions

PERATING THE DOORCOM™WIRELESS INTERCOM...................11

XPOSURE TO RADIO FREQUENCY ENERGY ..............................12

SAFETY STANDARDS ..................................................................12

Licensing

FCC Licensing .....................................................................13

How to Obtain an FCC Radio License .................................13

INDUSTRY CANADA Regulations.......................................13

INDUSTRY CANADA License Application...........................13

Service.................................................................................13

Warranty

RITRON, INC. LIMITED WARRANTY.........................................14

RDC-S

ERIES

OOR

™

ODELS

........

The radio transceiver’s model number appears on the serial la-

bel located on the bottom-side of the metal enclosure.

VHF Models

RDC-146 VHF Wireless Intercom

2 Watts, 150 - 165 MHz

RDC-146M VHF MURS License-Free,

Wireless Intercom,

2 Watts, 7 MURS Frequencies Only

RDC-146-BC VHF Wireless Intercom

2 Watts, 150-165MHz

(British Columbia)

RDC-146-Canada VHF Wireless Intercom

2 Watts, 150-165MHz

UHF MODELS

RDC-446 UHF Wireless Intercom

2 Watts, 450-470MHz

RDC-446-Canada UHF Wireless Intercom

2 Watts, 450-470MHz

RDC-Series DoorCom

Wireless Intercom Basic Operation

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com page 1

YSTEM

OMPONENTS

.........................................................................

The DoorCom™Wireless Intercom System provides 2-way, voice communication from delivery doors or other fixed locations to radio-

equipped personnel in or around the facility. The rugged, all-metal, weather-resistant speaker intercom box can be mounted outdoors

and is connected to the AC powered radio transceiver (indoors) with the 20ft connecting cable.

The DoorCom™wireless intercom consists of 6 components.

1. The R-Series Radio Transceiver

2. RPS-1B - 110VAC AC Power Adaptor

3. AFB-1545 - BNC Flexible Antenna

4. T-25 TORX bit

5. RDC-1, Stainless Steel, Speaker Intercom Box with 20 ft

Connecting Cable attached (connects RDC-1 to radio)

6. Wall Mount Bracket for radio transceiver

R-Series RDC-1 w/20 ft Cable RPS-1B, 110VAC AFB-1545 Mounting Bracket

Transceiver PN#60201121 AC Adapter Antenna

OPTIONAL AND REPLACEMENT ACCESSORY EQUIPMENT

Available options include:

•AFB-1545 – Replacement, Molded Flex, Dual-Band Replacement Antenna

•RAM - 1545 – Optional, Magnet Mounted, Dual-Band Antenna w/BNC Connector

•RPS-1B – Replacement, 110VAC to 12VDC Power Supply.

•JBS-MMK – Replacement, Mobile Mounting Kit.(Does not include screws to mount bracket to the wall)

•RDC-1 – Replacement, RDC-1, metal speaker intercom box. Includes PN#60201121 20ft cable, connects to radio.

•PN# 60201121 – 20ft Cable (RDC-1 to R-Series Transceiver) 2.5mm/3.5mm plug to spade lugs.

For additional information and pictures of these items go to http://www.ritron.com/doorcom.html and download pdf of the product bro-

chure.

RIEF

EATURE

VERVIEW

..................................................................

•Narrow Band FCC Compliant. The radio is compliant with

the Federal Commuinication Commission’s 2013 Narrow

Band Mandate – go to www.ritron.com for more information.

•Field-Programming. Field-programming allows you to

program specific features of the radio without a PC or special

software.

•License-Free VHF MURS Model. The VHF RDC-146M

model can be programmed from a list of 7 VHF MURS

frequencies. These FCC frequencies are for business-only

use and license-free.

•Licensed VHF and UHF Models. These models contain

table frequencies that require an FCC license. They can also

be PC programmed to “custom” frequencies making the

DoorCom™system compatible with an existing radio system

or even radio repeaters.

•Speaker Volume. Field-settable in pre-set levels 0-9.

•Multi-Channel Pre-Sets – Up to 10 different pre-set

channels

•Auto-ON When AC Power Applied – If AC power is

removed from the radio i.e. a power failure, the radio will

automatically turn ON, whenever AC power is restored.

•Mode of Operation. The DoorCom™Wireless Intercom can

operate in one of two possible modes.

o“Automatic Turn-Off” Mode (Factory Default). The radio

and speaker are OFF until the Call Button is pressed.

Radio and speaker remain ON subject to activity on the

channel and the reset timer setting (Default 10 seconds).

o“Intercom” Mode. The radio and speaker are always ON.

•DoorCom™Time-Out Tone – A double tone alerts the visitor

when the speaker has turned OFF. The same tone is

transmitted to radio-equipped personnel to signal that the

RDC-1 speaker has turned off and internal radio

communication can now continue.

•Choose From Two Distinct Call Tones – “Door Bell” or

“Ringing Tone”.

•Interference Eliminator Codes - Quiet Call (QC) and Digital

Quiet Call (DQC) codes can be programmed to eliminate

other radio users not in your workgroup. For compatibility,

new radios must be programmed with the same codes.

•Manager Lock - Prevents radio controls from being changed

by unauthorized personnel.

•DTMF Signaling - 1-9 digit DTMF codes can be transmitted

at the beginning of each message for radio identification.

RDC-Series DoorCom

Wireless Intercom Basic Operation

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com page 2

ONTROLS

ONNECTORS

UTTONS

.................................................

1 Multi-Function LED Display

The LED display will indicate the current Operating

Channel, the Speaker Volume setting (0-9), the Manager

Lock condition and Field-Programming Information.

2 Channel Select Button

Press the Channel Button to advance to the next

programmed channel.

3 Speaker Volume-Up/Down Buttons

Press the Volume Up Button to increase the volume, and

press the Volume Down Button to decrease the volume.

The volume level will be displayed momentarily in the

channel display.

4 Speaker/Microphone Connection

The RDC-1 Speaker Intercom Box is connected to the

radio here using the 2-PIN Connecting Cable PN#

60201121.

5 Power Connector

The Power Connector on the top of the radio is used to

connect power to the unit. Use the included 110VAC,

RPS-1B AC Adapter.

6 BNC Antenna

The antenna radiates and receives radio signals. The

included AFB-1545 Antenna connects to the BNC

Connector on the top of the radio.

7 Radio Program Button

When the radio is in PTT Programming Mode, the

Program Button is used to change channel information.

The channel display will display the programming

information as it is entered.

8 RDC-1, Rugged, Stainless Steel Intercom Box

Tough, weather-resistant, all-metal enclosure protects

against damage from weather and vandalism. Includes

mutliple mounting options without brackets.

Figure 1: RDC-1 and R-Series Radio, Controls and Connectors

9 Weather-Resistant Speaker (RDC-1)

Weather-resistant speaker is protected from vandalism by metal

speaker/mic guard. Speaker allows you to hear radio

transmissions on your radio frequency.

10 Weather-Protected Electret Microphone (RDC-1)

Weather-protected mic is also protected from damage by metal

speaker/mic guard. Allows your voice to be heard in

transmissions to other radios.

11 Weather-Proof, Vandal-Resistant PTT Button (RDC-1)

Rugged metal PTT Button protects against damage from

vandals. Press and Hold to talk, release to listen.

NITIAL

-U

ROGRAMMING

.........................................................

IMPORTANT - BEFORE permanently installing the DoorCom™wireless intercom, you will need to review how you would like the Door-

Com™to operate. You will then need to temporarily set-up the system and apply power to the radio. This is necessary to program the

radio and then test the system to confirm you have programmed it correctly.

For example:

•You will need to decide which DoorCom™radio frequency and interference eliminator codes you intend to use.

•You will need to decide which of the two possible Modes of Operation you intend to use.

•You will need to decide where you intend to install the R-Series radio transceiver (INDOOR only mounting).

•Keep in mind, you will need to provide 110VAC to within a few feet of the radio.

•You will need to decide where you intend to install the RDC-1 speaker intercom box (INDOOR/OUTDOOR).

•The RDC-1 to radio connecting cable is 20ft. in length.

•The location of the antenna will also need to be clear of any metal objects and power lines.

•Keep clearance at least 3 feet in all directions.

5 6

RDC-Series DoorCom

Wireless Intercom Programmable Features

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com page 3

ROGRAMMABLE

EATURES

................................................................

Review the features below to determine how your system will

operate. Certain features have been pre-configured as the

Factory Default setting and do not require reprogramming.

Some of the features listed can be Field-Programmed (FP)

without additional tools, and other features require a computer

and programming software (PC). Please call Ritron if you have

any questions or require special programming.

Glossary of Terms

FP = Field-Programmable Feature– no PC & software

required.

PC = PC Programmable Feature with PC & Software

Automatic Turn-Off Mode – Speaker and radio both

automatically turn off after programmable period of inactivity.

Intercom Mode – Automatic Turn-Off feature has been

disabled, the radio is able to receive calls at any time.

Inactivity Time – A continuous period of time where the radio

transceiver is not sending or receiving a call.

1. Field-Programming Enable..................... (PC)

This feature is ENABLED as the Factory Default setting.

If Field-Programming is enabled, the radio can be field-

programmed from a list pre-determined Table Frequencies,

Interference Eliminator codes and other FP features.

If DISABLED, all features must be programmed using special

Ritron PC Programming software and a computer.

2. Mode of Operation - A or B............(PC or FP)

A). Automatic Turn-Off Mode

Feature is ENABLED as Factory Default setting.

The speaker and the radio will turn OFF when the Reset Time

has expired. The Reset Time is a pre-programmed amount of

time of “inactivity” (no calls transmitted, no calls received)

before the speaker and radio turns off. The speaker and radio

are turned ON when the PTT button is pressed.

B). Intercom Mode

If Automatic Turn-Off is NOT enabled, the speaker and the

radio are always on… i.e. Intercom mode. This mode allows

the speaker to hear radio calls all the time.

3. Send A Call Tone ..........................(PC or FP)

Feature is ENABLED as Factory Default setting.

Choose from 2 call tones – Door Bell sound (Factory Default)

or Ringing sound.

The radio can be programmed to transmit of the 2 Call Tones

upon the initial press of the PTT button. This will signal radio-

equipped personnel that the call is originating from the

DoorCom™wireless intercom.

4. Send DoorCom™Time-OutTone..............(PC or FP)

Feature is ENABLED as Factory Default setting.

A HI/Low double-tone alerts the visitor that the speaker has

turned OFF. The same tone is transmitted to radio-equipped

personnel to signal that the RDC-1 speaker is now off and

internal radio communication can continue.

5. Manager Lock................................................................(FP)

Factory Default setting is: “UNLOCKED”.

When radio controls are “Locked”, the operating channel and

speaker volume settings cannot be changed.

Press the VOL Up AND VOL Dwn buttons simultaneously for 5

seconds. The display will show the current setting:

“U” = Unlocked “L” = Locked.

Repeat the above step to toggle between “U” and “L” condition.

6. Inactivity Reset Time ....................(PC or FP)

Factory Default setting: 10 seconds.

The Reset Time can be Field-Programmed to 9 different times

ranging from 5 seconds to 4 minutes, or PC programmed for

5 to 255 seconds. In Automatic Turn-Off mode a longer Reset

Time will allow more time for a response before the speaker

and the radio turn off.

7. Busy Channel TX Inhibit................(PC or FP)

Feature is DISABLED as Factory Default setting.

With this feature enabled the radio cannot transmit when there

is a received signal on the frequency. When a received signal

is present and the PTT buton is pressed, a “busy signal” will be

heard in the RDC-1 speaker.

8. Transmit Beep Enable.............................(PC)

Feature is ENABLED as Factory Default setting.

A short beep will sound in the RDC-1 speaker any time the

PTT button is pressed. This indicates to the user that the

intercom is ready to transmit their message.

9. RX Courtesy Beep Enable........................(PC)

Feature is DISABLED as Factory Default setting.

In high noise environments it is sometimes difficult to

determine when a received message has ended. With the RX

Courtesy Beep enabled the radio will sound a short beep on

the speaker at the end of each received transmission.

10. DTMF ANI ............................................(PC)

The radio can be programmed to send a 1-9 digit DTMF ANI

code at the beginning of each transmission. Allows Caller ID in

only those radio systems equipped with DTMF Decode.

11. TX Time Out Time ................................(PC)

Factory Default setting is 60 seconds.

The TX Time Out Time can be programmed for 1-255 seconds.

This sets the length of time the radio can transmit continuously.

If the PTT button is held down longer then the TX Time Out

Time, the radio will stop transmitting and a “Busy Signal” will

be heard in the speaker until the button is released.

12. Custom Frequency Programming ...........(PC)

The radio can be PC programmed with Ritron R-Series

software to operate on custom narrow band frequencies within

the radios specific operating band. MURS model cannot be

custom programmed to other frequencies.

RDC-Series DoorCom

Wireless Intercom Field Programming

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com page 4

OW TO

EADOUT

URRENT

ADIO

REQUENCY

ONE

ODES

..........

1. Connect the RDC-1 and 20 ft cable to the R-Series radio.

2. Attach the antenna to the radio.

3. Locate the RPS-1B AC adapter (do not connect it to the radio yet).

4. Press and HOLD the Program Button (See Figure 1 on page 2 for location) and now connect power to the radio using the RPS-1B

AC adapter, the radio will now turn ON. A "P" will appear on the program display and the speaker will beep rapidly.

5. When the beeping stops, release the Program Button. The radio will display a series of six characters for Radio Identification, with

each character separated by a hyphen. The 1st two characters indicate the Model Number, the 3rd and 4th characters indicate the

radio type, and the 5th and 6th characters indicate the firmware revision.

For this example: Model: 01

Radio Type: 31

Firmware Revision: 51

MODEL RADIO TYPE FIRMWARE REVISION

6. After the Radio Identification has been displayed, the digit 1 will appear, followed by a hyphen and the speaker will sound a triple

beep indicating that the radio is in Program Mode and Channel 1 is selected.

7. Press the Channel selector to select the channel to be read out. The channel number will appear briefly on the display as you step

through the channels. When you have settled on a channel a hyphen will appear across the center of the display to indicate that it

is ready for readout.

8. Press and RELEASE the Volume Up Button (See FIG-1 on page 2 for location). The radio will immediately begin to display a

series of four digits; with each digit separated by a hyphen.

9. The first two digits indicate the frequency code and the last two digits the tone code; see Table 1 and Table 2 on pages 6 and 7.

In this example an R-446 is programmed to operate on the “Brown Dot” frequency of 464.500 MHz (Frequency code “04”) with

100.0 Hz tone (Tone code “12”).

FREQUENCY CODE TONE CODE

10. If a 5th digit is displayed, the channel has been programmed for DQC and the last three digits indicate the DQC code; see Table 3

on page 7. In this example an R-446 was programmed to operate on the “Brown Dot” frequency of 464.500 MHz (Frequency code

“04”) with a DQC code of “723”.

FREQUENCY CODE DQC CODE

11. If the channel is PC programmed with any frequency or tone not listed in Table 1, Table 2 or Table 3 on pages 6 and 7, the radio

will sound the ERROR TONE on contents read out and display an "E". The PC programmer will be required to readout the radios

frequency and tone programming.

12. To return the radio to normal operation:

1) Disconnect the AC adapter from the radio.

2) THEN reconnect the AC adapter to the radio.

RDC-Series DoorCom

Wireless Intercom Field Programming

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com page 5

OW TO

IELD

ROGRAM

REQUENCY

ONE

ODES

..........................

To match other radios, the owner can select Frequency, Tone and DQC Codes from Table 1, Table 2 and Table 3 on pages 6 and 7. In

our example, we will program an R-446 to operate on the "Brown Dot" frequency of 464.500 MHz with 100.0 Hz tone.

1. Connect the RDC-1 and 20 ft cable to the R-Series radio.

2. Attach the antenna to the radio.

3. Locate the RPS-1B AC adapter (do not connect it to the radio yet).

4. Refer to Table 1 on page 6 to determine the two-digit frequency code for 464.500 MHz and write it down.

5. Refer to Table 2 on page 7 to determine the two-digit tone code for 100.0 Hz and write it down.

6. Press and HOLD the Program Button (See Figure 1 on page 2 for location) and now connect power to the radio

using the RPS-1B AC adapter, the radio will now turn ON. A "P" will appear on the program display and the

speaker will beep rapidly.

7. When the beeping stops, release the Program Button. The radio will display a series of six characters for Radio

Identification, with each character separated by a hyphen. The 1st two characters indicate the Model Number,

the 3rd and 4th characters indicate the radio type, and the 5th and 6th characters indicate the firmware revision.

For this example: Model: 01

Radio Type: 31

Firmware Revision: 51

MODEL RADIO TYPE FIRMWARE REVISION

8. After the Radio Identification has been displayed, the digit 1 will appear, followed by a hyphen and the speaker

will sound a triple beep indicating that the radio is in Program Mode and Channel 1 is selected.

9. Press the Channel selector to select the channel to be programmed. The channel number will appear briefly on

the display as you step through the channels. When you have settled on a channel a hyphen will appear across

the center of the display to indicate that it is ready for programming.

10. Enter the 1st digit of the frequency code by pressing the Program button until the display shows the desired

number. Pause—the speaker will sound a low tone and the radio will show a hyphen across the center of the

display to indicate that it is ready to accept the next digit.

11. Enter the 2nd digit of the frequency code by pressing the Program button until the display shows the desired

number. Pause—the speaker will sound a low tone and the radio will show a hyphen across the center of the

display to indicate that it is ready to accept the next digit.

12. Enter the 1st digit of the tone code (or 1st digit of the DQC code) by pressing the Program button until the display

shows the desired number. Pause—the speaker will sound a low tone and the radio will show a hyphen across

the center of the display to indicate that it is ready to accept the next digit.

13. Enter the 2nd digit of the tone code (or 2nd digit of the DQC code) by pressing the Program button until the display

shows the desired number. Pause—the speaker will sound a low tone and the radio will show a hyphen across

the center of the display to indicate that it is ready to accept the next digit.

14. FOR DQC CODES ONLY – Enter the 3rd digit of the DQC code by pressing the Program button until the display

shows the desired number. Pause—the speaker will sound a low tone and the radio will show a hyphen across

the center of the display to indicate that it is ready to accept the next digit.

15. Press and release the Volume Up button to SAVE your programming. A triple beep will sound to indicate that

programming was successful and a hyphen will appear on the program display. The radio is now ready for

another program entry.

NOTE: An error tone will sound if you attempt to save an incorrect code, an "E" will appear on the display.

Check the digits you are attempting to enter, then re-enter.

16. To return the radio to normal operation:

1) Disconnect the AC adapter from the radio.

2) THEN reconnect the AC adapter to the radio.

RDC-Series DoorCom

Wireless Intercom Field Programming

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com page 6

ABLE

ROGRAMMABLE

REQUENCY

ODES

.........................................................

UHF Business Band

Code Frequency ColorDot BW

01 467.7625 J 12.5

02 467.8125 K 12.5

03 464.5500 Yellow Dot 12.5

04 464.5000 Brown Dot 12.5

05 467.8500 Silver Star 12.5

06 467.8750 Gold Star 12.5

07 467.9000 Red Star 12.5

08 467.9250 Blue Star 12.5

09 469.2625 12.5

10 462.5750 White Dot 12.5

11 462.6250 Black Dot 12.5

12 462.6750 Orange Dot 12.5

13 464.3250 12.5

14 464.8250 12.5

15 469.5000 12.5

16 469.5500 12.5

17 463.2625 12.5

18 464.9125 12.5

19 464.6000 12.5

20 464.7000 12.5

21 462.7250 12.5

22 464.5000 12.5

23 464.5500 12.5

24 467.7625 12.5

25 467.8125 12.5

26 467.8500 12.5

27 467.8750 12.5

28 467.9000 12.5

29 467.9250 12.5

30 461.0375 12.5

31 461.0625 12.5

32 461.0875 12.5

33 461.1125 12.5

34 461.1375 12.5

35 461.1625 12.5

36 461.1875 12.5

37 461.2125 12.5

38 461.2375 12.5

39 461.2625 12.5

UHF Business Band

Code Frequency ColorDot BW

40 461.2875 12.5

41 461.3125 12.5

42 461.3375 12.5

43 461.3625 12.5

44 462.7625 12.5

45 462.7875 12.5

46 462.8125 12.5

47 462.8375 12.5

48 462.8625 12.5

49 462.8875 12.5

50 462.9125 12.5

51 464.4875 12.5

52 464.5125 12.5

53 464.5375 12.5

54 464.5625 12.5

55 466.0375 12.5

56 466.0625 12.5

57 466.0875 12.5

58 466.1125 12.5

59 466.1375 12.5

60 466.1625 12.5

61 466.1875 12.5

62 466.2125 12.5

63 466.2375 12.5

64 466.2625 12.5

65 466.2875 12.5

66 466.3125 12.5

67 466.3375 12.5

68 466.3625 12.5

69 467.7875 12.5

70 467.8375 12.5

71 467.8625 12.5

72 467.8875 12.5

73 467.9125 12.5

74 469.4875 12.5

75 469.5125 12.5

76 469.5375 12.5

77 469.5625 12.5

99 No change ---

VHF Business Band

Code Frequency ColorDot BW

03 151.625 Red Dot 12.5

04 151.955 Purple Dot 12.5

05 151.925 12.5

06 154.540 12.5

07 154.515 12.5

08 154.655 12.5

09 151.685 12.5

10 151.715 12.5

11 151.775 12.5

12 151.805 12.5

13 151.835 12.5

14 151.895 12.5

15 154.490 12.5

16 151.655 12.5

17 151.745 12.5

18 151.865 12.5

24 151.700 12.5

25 151.760 12.5

26 152.700 12.5

99 No change ---

VHF MURS**

Code Frequency ColorDot BW

01 154.600 Green Dot 25

02 154.570 Blue Dot 25

19 151.820 MURS 12.5

20 151.880 MURS 12.5

21 151.940 MURS 12.5

22 154.600 MURS 12.5

23 154.570 MURS 12.5

Notes

** MURS frequencies do not require an

FCC license. All other frequencies re-

quire an FCC license.

•BW is the bandwidth in kHz.

•12.5 kHz indicates a narrow band

channel. 25kHz indicates a wide band

channel.

Notes: 1. If the R-Series Radio has been PC programmed to a non-table frequency it cannot be changed via field programming. You

can, however, change the QC or DQC Tone Code via field programming by using the “No Change” Frequency Code “99”

followed by the desired QC or DQC Tone Code.

2. For the VHF Model R-146, only VHF Business Band Frequency Codes 03-18, and 24-26 are available.

3. For the VHF MURS Model R-146M, only VHF MURS Frequency Codes 01, 02, 19-23 are available.

ANADIAN

REQUENCY

ODES

..................................................................................

Canada Models

UHF Business Band

Code Frequency ColorDot BW

01 458.6625 25

02 469.2625 25

Canada Models

VHF Business Band

Code Frequency ColorDot BW

01 151.055 25

02 151.115 25

British Columbia Models

VHF Business Band

Code Frequency ColorDot BW

01 154.100 25

02 158.940 25

RDC-Series DoorCom

Wireless Intercom Field Programming

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com page 7

ABLE

NTERFERENCE

LIMINATOR

ROGRAMMABLE

ONE

ODES

...................

Code Frequency

01 67.0

02 71.9

03 74.4

04 77.0

05 79.7

06 82.5

07 85.4

08 88.5

09 91.5

10 94.8

11 97.4

12 100.0

13 103.5

Code Frequency

14 107.2

15 110.9

16 114.8

17 118.8

18 123.0

19 127.3

20 131.8

21 136.5

22 141.3

23 146.2

24 151.4

25 156.7

26 162.2

Code Frequency

27 167.9

28 173.8

29 179.9

30 186.2

31 192.8

32 203.5

33 210.7

34 218.1

35 225.7

36 233.6

37 241.8

38 250.3

39 69.4

Code Frequency

40 159.8

41 165.5

42 171.3

43 177.3

44 No Tone

45 183.5

46 189.9

47 196.6

48 199.5

49 206.5

50 229.1

51 254.1

00 No Tone

ABLE

IGITAL

NTERFERENCE

LIMINATOR

ROGRAMMABLE

DQC

ONE

ODES

...

Code

023

025

026

031

032

036

043

047

051

053

054

065

071

Code

072

073

074

114

115

116

122

125

131

132

134

143

145

Code

152

155

156

162

165

172

174

205

212

223

225

226

243

Code

244

245

246

251

252

255

261

263

265

266

271

274

306

Code

311

315

325

331

332

343

346

351

356

364

365

371

411

Code

412

413

423

431

432

445

446

452

454

455

462

464

465

Code

466

503

506

516

523

532

546

565

606

662

612

624

627

Code

631

632

645

654

664

703

712

723

731

732

734

743

754

ABLE

DVANCED

EATURE

ODES

......................................................................

Code Feature Default Description

Inactivity Reset Time

801 5 seconds Inactivity Reset Time is the length of time the radio can remain

802 10 seconds √inactive (not receiving or transmitting) before the audio is muted.

803 20 seconds

804 30 seconds

805 45 seconds

806 1 minute

807 2 minutes

808 3 minutes

809 4 minutes

Special Features

825 Enable Auto Turn-Off √Radio’s audio will automatically mute when the radio has not been used(transmit or

receive) for a period of time longer than the Reset Time. Callbox Mode

828 Disable Auto Turn-Off Radio’s audio will not mute when the radio has not been used(transmit or receive) for a

period of time longer than the Reset Time. Intercom Mode.

827 Enable Busy Channel TX Inhibit Radio cannot transmit when there is a received signal. A “busy signal” will be heard on the

RDC-1 speaker when the PTT is pressed and a received signal is present.

828 Disable Busy Channel TX Inhibit √Radio will transmit whenever the PTT is pressed, regardless of any received signal.

831 Enable “Ring” Call Tone Radio will transmit Ringing Call Tone when PTT is pressed and no return call is received.

832 Enable “Doorbell” Call Tone √Radio will transmit simulated Doorbell Call Tone when PTT is pressed and no return call is

received.

833 Enable Time-Out Tone √At the end of the Activity Reset Time, the radio will transmit a hi/low tone to other

receiving radios.

834 Disable Time-Out Tone At the end of the Activity Reset Time, the radio will not transmit a hi/low tone to other

receiving radios.

√Denotes the R-Series transceiver factory default settings.

RDC-Series DoorCom

Wireless Intercom Field Programming

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com page 8

ABLE

INGLE

IGIT

ADIO

EATURE

ODES

........................................................

Code Feature Default Description

1 - 8 Unused

9 Call Tone ON √When PTT button is initially pressed a Call Tone will be transmitted.

0 Call Tone OFF

OW TO

IELD

ROGRAM

EATURE

ODES

...........................................

The RDC-Series Radio can be field programmed for a number of simple and advanced features. Refer to Table 5 below for the simple,

single digit codes available for field programming. Refer to Table 4 for the advanced three digit codes available for field programming.

In our example we will program an R-146 for an Inactivity Reset Time of 30 seconds.

1. Refer to Table 5 to determine the three-digit feature code and write it down.

2. Press and HOLD the Program Button (See FIG-1 on page 2 for location) and now connect power to the radio

using the RPS-1B AC adapter, the radio will now turn ON. A "P" will appear on the program display and the

radio will beep rapidly.

3. When the beeping stops, release the PTT Button. The radio will display a series of six characters for Radio

Identification, with each character separated by a hyphen. The 1st two characters indicate the Model Number,

the 3rd and 4th characters indicate the radio type, and the 5th and 6th characters indicate the firmware revision.

For this example: Model: 01

Radio Type: 31

Firmware Revision: 51

MODEL RADIO TYPE FIRMWARE REVISION

4. After the Radio Identification has been displayed, the digit 1 will appear, followed by a hyphen and the speaker

will sound a triple beep indicating that the radio is in Program Mode and Channel 1 is selected.

5. Press the Channel selector to select the channel to be programmed. The channel number will appear briefly on

the display as you step through the channels. When you have settled on a channel a hyphen will appear across

the center of the display to indicate that it is ready for programming.

6. Enter the 1st digit of the feature code by pressing the Program button until the display shows the desired number.

Pause—the speaker will sound a low tone and the radio will show a hyphen across the center of the display to

indicate that it is ready to accept the next digit.

NOTE: If entering a simple, single digit code skip to step 10.

7. Enter the 2nd digit of the feature code by pressing the Program button until the display shows the desired

number. Pause—the speaker will sound a low tone and the radio will show a hyphen across the center of the

display to indicate that it is ready to accept the next digit.

8. Enter the 3rd digit of the feature code by pressing the Program button until the display shows the desired number.

Pause—the speaker will sound a low tone and the radio will show a hyphen across the center of the display to

indicate that it is ready to accept the next digit.

9. Press and release the Volume Up button to SAVE your programming. A triple beep will sound to indicate that

programming was successful and a hyphen will appear on the program display. The radio is now ready for

another program entry.

NOTE: An error tone will sound if you attempt to save an incorrect code, an "E" will appear on the display.

Check the digits you are attempting to enter, then re-enter.

10. When you have made your final program entry and to return the radio to normal operation:

1) Disconnect the AC adapter from the radio.

2) THEN reconnect the AC adapter to the radio.

804

RDC-Series DoorCom

Wireless Intercom Installation Instructions

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com page 9

RDC-1

PEAKER

NTERCOM

NSTALLATION

NSTRUCTIONS

.............

If you intend to mount the metal RDC-1 speaker intercom box on

an outside wall, it will be necessary to route the special

connecting cable through a hole in the exterior wall.

To make the routing process easier and the required hole

smaller, we suggest routing the end of the cable that contains

the 3 spade lugs. You will need to spearate the front of the RDC-

1 from the back and disconnect the three spade lugs from the

screw terminals.

When ready to pass the cable through the hole, attach a “pull

line” BELOW the crimp attachment point of the spade lugs and

gentely pull the cable through the hole (refer to Figure-2).

The RDC-1 Speaker Intercom Box can be secured to virtually to

any surface (INDOOR/OUTDOOR) using up to four (4) screws

(not included).

Installation of RDC-1: (Refer to Figure-2)

1. Determine the method of securing the RDC-1.

a. Use the holes in the mounting tabs on the sides of the

RDC-1.

b. OR Use the mounting holes located directly on the back

of the RDC-1.

2. Determine the routing of the RDC-1 Cable.

a. Through the back of the RDC-1.

b. OR Through the bottom of the RDC-1.

3. Choose a size, type of screw thread and screw length which

will hold firmly in the surface to which the unit will be

mounted.

4. If required, drill the (2) holes to secure the RDC-1 into the

wall mounting surface.

5. If required, drill the hole to route the RDC-1 Cable through

the mounting surface. The hole must be large enough to

pass the cable end containing the (3) spade lugs. We

suggest a 0.5”(1/2”)minimum diameter size hole.

6. Route the RDC-1 Cable through the drilled hole.

7. Using the included Torx bit, remove the (2) T-25 TORX

screws securing the front and rear panels of the RDC-1.

8. Secure the rear panel of the RDC-1 to the mounting surface

using the (2) screws selected in Step 3.

9. If routing RDC-1 Cable through the bottom of the rear panel,

remove the conduit plug, install the require length of conduit,

and route the RDC-1 Cable through the conduit into the

RDC-1 box.

10. CAREFULLY re-connect the (3) spade lugs of the RDC-1

Cable to the (3) correct screw terminals located on the

inside of the front panel.

Take care to match the name on the spade lug label to

the same name printed near the screw terminal (refer to

Figure-2).

11. Secure the RDC-1 Cable to the RDC-1 rear panel tab using

the small cable tie (refer to Figure-2).

12. Place the RDC-1 front panel over the rear panel and secure

with the (2) T-25 TORX screws.

13. You may want to consider routing the connecting cable

through conduit and attaching the conduit to the RDC-1

(back or bottom hole). The hole size in the RDC-1 is

0.875”(7/8”).

Figure-2; RDC-1 Installation

Secure RDC-1 Cable with Cable Tie Here

ttach “Pull Line” Here

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ritron Gegensprechanlage Handbücher

Ritron

Ritron " 6 " SERIES OUTPOST Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung