RKI Instruments 61-1020 Bedienungsanleitung

RKI Instruments, Inc.

www.rkiinstruments.com

61-1020/61-0230

Molecular Property Spectrometer

Combustible Gas Detector

Operator’s Manual

Part Number: 71-0592

Revision: P2

Released: 10/14/22

2• 61-1020/61-0230 Molecular Property Spectrometer Combustible Gas Detector

WARNING

Read and understand this instruction manual before operating

detector. Improper use of the detector could result in bodily harm or

death.

Periodic calibration and maintenance of the detector is essential for

proper operation and correct readings. Please calibrate and maintain

this detector regularly! Frequency of calibration depends upon the

type of use you have and the sensor types. For most applications,

typical calibration frequencies are between 6 and 12 months but can

be more often or less often based on your usage.

61-1020/61-0230 Molecular Property Spectrometer Combustible Gas Detector • 3

Product Warranty

RKI Instruments, Inc. warrants gas alarm equipment sold by us to be free from defects in

materials, workmanship, and performance for a period of two years from date of shipment from

RKI Instruments, Inc. Any parts found defective within that period will be repaired or replaced, at

our option, free of charge. This warranty does not apply to those items which by their nature are

subject to deterioration or consumption in normal service, and which must be cleaned, repaired, or

replaced on a routine basis. Examples of such items are:

• Absorbent cartridges

• Pump diaphragms and valves

•Fuses

•Batteries

• Filter elements

Warranty is voided by abuse including mechanical damage, alteration, rough handling, or repair

procedures not in accordance with the operator’s manual. This warranty indicates the full extent

of our liability, and we are not responsible for removal or replacement costs, local repair costs,

transportation costs, or contingent expenses incurred without our prior approval.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY AND ALL OTHER WARRANTIES AND

REPRESENTATIONS, EXPRESSED OR IMPLIED, AND ALL OTHER OBLIGATIONS OR

LIABILITIES ON THE PART OF RKI INSTRUMENTS, INC. INCLUDING BUT NOT LIMITED TO,

THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR APARTICULAR PURPOSE. INNO

EVENT SHALL RKI INSTRUMENTS, INC. BE LIABLE FOR INDIRECT, INCIDENTAL, OR

CONSEQUENTIAL LOSS OR DAMAGE OF ANY KIND CONNECTED WITH THE USE OF ITS

PRODUCTS OR FAILURE OF ITS PRODUCTS TO FUNCTION OR OPERATE PROPERLY.

This warranty covers instruments and parts sold to users by authorized distributors, dealers, and

representatives as appointed by RKI Instruments, Inc.

We do not assume indemnification for any accident or damage caused by the operation of this gas

monitor, and our warranty is limited to the replacement of parts or our complete goods.

4• 61-1020/61-0230 Molecular Property Spectrometer Combustible Gas Detector

Table of Contents

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

MPS Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Junction Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Mounting the Combustible Gas Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Wiring the Combustible Gas Detector to a Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Startup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Introducing Incoming Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Setting the Zero Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Replacing the Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Calibration Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Preparing for Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Setting the Zero Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Setting the Response Reading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

61-1020/61-0230 Molecular Property Spectrometer Overview • 5

Overview

This manual describes the 61-1020 combustible gas detector. This manual also describes how to

install, start up, maintain, and calibrate the detector when used with a gas monitoring controller. A

parts list at the end of this manual lists replacement parts and accessories for the combustible gas

detector.

The 61-1020 combustible gas detector includes a junction box. This manual may also be used for

the 61-0230 combustible gas detector which does not include a junction box and is normally

mounted in one of a controller’s conduit hubs. If you are using a 61-0230 combustible gas

detector, disregard all references to the junction box and junction box terminal block.

Specifications

Table 1 specifies the detection range and accuracy for the 14 gases that the MPS sensor can

reliably detect at the same time.

Table 1: Detection Ranges and Accuracy

Target Gas Formula Detection Range Accuracy

(0 to 50% LEL)

Butane C4H10 0 - 100% LEL ± 5% LEL

Ethane C2H60 - 100% LEL ± 5% LEL

Hydrogen H20 - 100% LEL ± 5% LEL

Isobutane HC(CH3)30 - 100% LEL ± 5% LEL

Isobutylene C4H80 - 100% LEL ± 5% LEL

Isopropanol C3H8O 0 - 100% LEL ± 10% LEL

Methane CH40 - 100% LEL ± 3% LEL

Methyl Ethyl Ketone C4H8O 0 - 100% LEL ± 5% LEL

Octane C8H18 0 - 100% LEL ± 5% LEL

Pentane C5H12 0 - 100% LEL ± 5% LEL

Propane C3H80 - 100% LEL ± 6% LEL

Propylene C3H60 - 100% LEL ± 5% LEL

Toluene C7H80 - 100% LEL ± 12% LEL

Xylene C8H10 0 - 100% LEL ± 12% LEL

NOTE: The MPS sensor will respond to other combustible gases, but the accuracy has only

been determined for these 14 gases.

6• Applications 61-1020/61-0230 Molecular Property Spectrometer

WARNING: When using the 61-1020/61-0230, you must follow the instructions and warnings

in this manual to assure proper and safe operation of the 61-1020/61-0230 and to

minimize the risk of personal injury. Be sure to maintain and periodically

calibrate the 61-1020/61-0230 as described in this manual.

Applications

The MPS combustible detector is most effective in the following applications:

• High concentrations of hydrogen sulfide (H2S) or silicones present where sensor

poisoning is a common problem

• High-humidity environments where catalytic or IR sensors may not hold up

• Environments more likely to have mixtures of hydrocarbons present

Table 2: Specifications

Target/Calibration Gas

With Junction Box

• 61-0230-CH4: Methane

• 61-0230-HC: General hydrocarbons (propane calibration standard)

Without Junction Box

• 61-1020-CH4: Methane

• 61-1020-HC: General hydrocarbons (propane calibration standard)

Area Classification Explosion-proof for Class I, Groups B, C, and D

Operating

Temperature Range

-20ºC to +50ºC (-4ºF to +122ºF)

Humidity Range 0 - 100% RH (non-condensing)

Pressure Range 80 to 120 kPa

Sampling Method Diffusion

Detection Range 0 to 100% LEL

Response Time 90% in 45 seconds

Dead Bands •Methane(CH

4): 3% LEL

• All other gases: 5% LEL

61-1020/61-0230 Molecular Property Spectrometer Description • 7

Description

The 61-1020 is a Molecular Property Spectrometer (MPSTM) type of detector which has some

advantages over a catalytic or IR type of combustible detector. The explosion-proof MPS detector

is immune to poisons, can be used in high humidity, can detect multiple gases simultaneously (see

Table 1), and does not require calibration as often as catalytic combustible sensors.

This section describes the components of the 61-1020: the MPS LEL detector and the junction

box.

Figure 1: Component Location

MPS Detector

The MPS LEL detector is made up of the MPS combustible gas LEL detector housed and

encapsulated in a pipe nipple. The pipe nipple has 3/4 NPT threads on each end and a 1-1/4 inch

hex that allows removal or installation of the detector with a wrench. A porous flame arrestor

coated with a hydrophobic film that repels liquids is on one end of the detector and allows sample

gas to enter the detector. Four color coded leads, red, white, green, and black, extend from the

other end of the detector. Use the leads when connecting the detector to the terminal block in the

junction box.

Junction Box

The junction box allows installation of the detector at a mounting site that is remote from the

controller while protecting the detector wiring connections. Two 3/4 NPT conduit hubs allow you

to mount the detector to the junction box and connect the wiring from the detector to a controller.

The terminal block within the junction box facilitates the wiring to the detector. A cover on the

front of the junction box allows access to the interior of the junction box. Three spacers installed

on the back of the junction box control the distance of the junction box from a mounting surface

and insure that there is enough room to install a calibration cup on the detector during calibration.

J-Box

Green

Red

White

Rubber

Spacers,

MPS LEL Detector

Black

8• Installation 61-1020/61-0230 Molecular Property Spectrometer

Installation

This section describes procedures to mount the combustible gas detector in the monitoring

environment and wire it to a controller.

If you purchased a 61-0230 detector that is factory installed and wired to a controller, detector

installation is not necessary, but the detector wiring can be confirmed as described in “Wiring the

Combustible Gas Detector to a Controller” on page 9.

Mounting the Combustible Gas Detector

1. Select a mounting site that is representative of the monitoring environment. Consider the

following when selecting the mounting site:

• Select a site where the detector is not likely to be bumped or disturbed. Make sure there is

sufficient room to perform start-up, maintenance, and calibration procedures.

• Select a site where the target gas is likely to be found first. For lighter gases, mount the

detector near the ceiling. For heavier gases, mount the detector near the floor.

Figure 2: Mounting the Combustible Gas Detector

2. At the selected mounting site, hang or mount the junction box with the detector facing down

(see Figure 2).

2.70 .38

J-Box

3/4 NPT

Female

Rubber

Spacers,

.75

3.65

MPS LEL Detector

7.10 MAX

61-1020/61-0230 Molecular Property Spectrometer Installation • 9

Wiring the Combustible Gas Detector to a Controller

WARNING: Always verify that the power to the controller is off before you make wiring

connections.

1. Turn off the controller.

2. Turn off or unplug power to the controller.

3. If the detector is mounted remotely from a controller using the junction box, proceed to

Step 4.

If the detector is mounted directly to a controller, it is normally factory wired. Confirm that

the detector’s wires are connected to the appropriate controller detector terminals and skip

to “Start Up” on page 11. See Figure 3, the controller operator’s manual, and the

controller’s detector head specification sheet for the 61-0230 detector for the wiring

connections.

4. Remove the cover from the junction box.

WARNING: To maintain the explosion proof classification of the detector/junction box

combination, a conduit seal must be used within 18 inches of the junction box

conduit hub used for wiring to the controller. Adhere to your local electrical

code when installing the conduit seal.

5. Guide a four-conductor, shielded cable or four wires in conduit through the unused conduit

hub of the junction box. Use appropriate conduit fittings and construction technique for the

environmental rating and hazardous location classification of the junction box. The junction

box is rated NEMA 4X and classified explosion proof for Class I, Groups B, C, and D.

6. Connect the wires to the terminal block in the junction box.

CAUTION: Leave the shield drain wire insulated and disconnected at the 61-1020.

You will connect the opposite end of the cable’s drain wire at the

controller.

7. Secure the junction box cover to the junction box.

8. Route the cable or wires in conduit leading from the detector through one of the conduit hubs

at the controller. Use appropriate conduit fittings and construction technique for the

environmental rating of the controller. RKI controllers are typically rated NEMA 4X, are not

explosion-proof, and must be installed in a non-hazardous location.

CAUTION: Do not route power and detector wiring through the same conduit hub.

The power cable may disrupt the transmission of the detector signal to

the controller.

9. Connect the wires to the applicable controller terminal strip. See the controller operator’s

manual and the controller’s detector head specification sheet for the 61-1020 detector.

10 • Installation 61-1020/61-0230 Molecular Property Spectrometer

Figure 3: Wiring the Combustible Gas Detector to a Controller

10. If using a shielded cable, connect the cable’s drain wire to an available chassis ground at the

controller. RKI controllers typically have a ground stud that is a convenient grounding

location.

Red

White

Green

Black

White

Green

Red

Detector Wires

Black

Terminal Strip

J-Box

Controller

LEL

Detector

Terminals

MPS LEL Detector

Cable Shield

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere RKI Instruments Gaswarngerät Handbücher

RKI Instruments

RKI Instruments 35-3001A-14 Bedienungsanleitung

RKI Instruments

RKI Instruments GX-2009 Bedienungsanleitung

RKI Instruments

RKI Instruments 65-2495RK Bedienungsanleitung

RKI Instruments

RKI Instruments 61-1004RK Bedienungsanleitung

RKI Instruments

RKI Instruments GX-3R Pro Bedienungsanleitung

RKI Instruments

RKI Instruments SD-1GH Bedienungsanleitung

RKI Instruments

RKI Instruments 65-2336RK Bedienungsanleitung

RKI Instruments

RKI Instruments 35-3010RK-07 Bedienungsanleitung

RKI Instruments

RKI Instruments GasWatch 2 Bedienungsanleitung

RKI Instruments

RKI Instruments GX-3R Pro Bedienungsanleitung

RKI Instruments

RKI Instruments AirLink 9850 Bedienungsanleitung

RKI Instruments

RKI Instruments GX-3R Pro Bedienungsanleitung

RKI Instruments

RKI Instruments RIKEN RX-516 Bedienungsanleitung

RKI Instruments

RKI Instruments T3A Bedienungsanleitung

RKI Instruments

RKI Instruments GasWatch 3 Bedienungsanleitung

RKI Instruments

RKI Instruments 35-3001-01 Bedienungsanleitung

RKI Instruments

RKI Instruments NP-204 Bedienungsanleitung

RKI Instruments

RKI Instruments GX-2003 Bedienungsanleitung

RKI Instruments

RKI Instruments 65-2438 Bedienungsanleitung

RKI Instruments

RKI Instruments 65-2380SS Bedienungsanleitung

RKI Instruments

RKI Instruments 65-2422RK-05 Bedienungsanleitung

RKI Instruments

RKI Instruments GD-70D Series Bedienungsanleitung

RKI Instruments

RKI Instruments EAGLE 2 Bedienungsanleitung

RKI Instruments

RKI Instruments 61-1006RK Bedienungsanleitung

Beliebte Gaswarngerät Handbücher anderer Marken

Macurco

Macurco GD-6 Bedienungsanleitung

Evikon

Evikon E2632 Bedienungsanleitung

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Bedienungsanleitung

MSA

MSA altair 5 Bedienungsanleitung

DOD Technologies

DOD Technologies ChemLogic CL96 Bedienungsanleitung

DEGA

DEGA NS III LCD Series Bedienungsanleitung

PEMTECH

PEMTECH PT2008 Series Bedienungsanleitung

Coster

Coster RGS 328 Bedienungsanleitung

Sygonix

Sygonix 2483186 Bedienungsanleitung

Perry

Perry 1GA 50917MET/P Bedienungsanleitung

isweek

isweek AS8900 Bedienungsanleitung

Oldham

Oldham OLC 10 Bedienungsanleitung

Wizmart

Wizmart NB983 Bedienungsanleitung

Beacon

Beacon MEGA Handbuch

RKI

RKI GX-6000 Bedienungsanleitung

Dräger

Dräger PIR 7000 Bedienungsanleitung

GDS

GDS GASMAX EC Bedienungsanleitung

Seitron

Seitron BE COOL R1 Bedienungsanleitung