Sea-Jet Evolution
3
Stage 1
Part No. Description, size in mm number required
1.5 Motor 2
1.6 Washer, D3.2 4
1.7 Cap head screw, M3x8 4
1.8 Coupling. D11 x 25 2
1.9 Socket grub screw, M3x 5 4
1.10 Propshaft, D4 x 168 2
1.11 Stuffing tube, D 6,5 x 120 2
1.12 Servo tray, 3 PP 1
1.13 Latch plate, 3 PP 1
1.14 Centre piece, 3 PP 1
• Assemble motors to motor mount, 1.4 using Cap screws, 1.7 and
washers, 1.6
• it grub screws, 1.9 to coupling, 1.8 and tighten on motor shaft.
• it Propshaft, 1.10 to stuffing tube, 1.11.
• Slide the servo tray, 1.12 into motor mount and secure with
latch plate, 1.13. DO NOT G UE
• Slide centre piece, 1.14 into its slot.
itting motors, 1.5 to motor mount, 1.4
In order that the motors may be removed from the model for routi-
ne maintenance, the motor mount is not bonded to the hull. The lug
over the top of the motor module is removed after complete instal-
lation in the hull (see page 15).
To remove the module, slide the latch plate upwards and then for-
wards to release.
Loosen grub screws, 1.9, disconnect motors, Pull motor mount, 1.4
and servo tray 1.12 upwards to release from hull.
Part No. Description, size in mm number required
1.15 Battery tray, 3 PP 1
1.16 ormer front, 3 PP 1
1.17 ormer rear, 3 PP 1
1.18 Battery retainer, 3 PP 2
1.19 Stop Plate, 3 PP 1
• it and glue formers, 1.16 and 1.17, the battery retainer, 1.18 to
battery tray, 1.15
• The stop plate, 1.19 is fitted dry in the tray. Thereby allowing dif-
ferent length/size battery packs to be used.
Assembly and operating instructions
©robbe Modellsport
No.
1266
• Fit but do not glue this assembly to the latch plate, 1.13.
Stage 2
Part No. Description, size in mm number required
2.1 Servo and fixings 1, NI
2.2 Servo arm 1, with 2.1
2.3 Receiver (Rx) 1, NI
2.4 ESC 2, NI
2.5 Hook and loop tape 3 each
• it grommets and brass ferrules to servo, mark hole positions,
drill 1,5 mm holes and screw servo, 2.1 to tray.
• Drill D2 hole in servo arm, 2.2 for rudder linkage, fit to servo.
• ix Rx, 2.3 and ESC, 2.4 with double sided hook and loop tape to
their positions on servo tray.
Part No. Description, size in mm number required
2.6 Rudder linkage, Br, D2 1
2.7 Pushrod keeper 1
2.8 Ball-link clevis 1
2.9 Rudder bearing/spacer, D6, 5 x 19 1
2.10 Tapered rudder, PM 1
2.11 O ring 1
2.12 Collet, D4 x D9 x5 1
2.13 Ball head bolt, 18 long 1
• Measure length of 148 mm required for rudder linkage wire, 2.6,
bend 90 degree on plain end and fit pushrod keeper, 2.7
• Screw ball-link clevis, 2.8 to threaded end of linkage.
• Test fit rudder assembly.
• it rudder bearing, 2.9 to servo tray.
• Slide rudder, 2.10 into bearing from underneath and fit O-ring,
2.11 to protruding shaft.
• Slide collet, 2.12 onto shaft and screw ball head bolt, 2.13 into
collet to retain rudder shaft.
• Set servo to neutral and fit linkage to servo and rudder
• Loosen, ball head bolt, 2.13 and remove rudder, 2.10 and spacer
2.9, set aside and keep safe until final fitment.
Stage 3
Part No. Description, size in mm number required
3.1 Deck, black 1.5 Vac 1
3.2 Cover, 1.5 ABS Pl, black 1
3.3 ormer, 3 PP 1
3.4 Doubler, 3 PP 1
3.5 Guide tube, Ali D4.2 x D5 x69 1
3.6 Seat rear, black 1.5 Vac 1
3.7 ormer, 3 PP 1
• Trial fit the black cover, 3.2 in rear deck, 3.1 opening.
Secure in position with strips of clear tape- see illustration “D”.
• Bond doubler, 3.4 to former 3.3. Pay attention to illustration “E”
and ensure that cutout “a” aligns with the cutout on former 3.3.
• Bond former 3.3 to the deck and file edge flush to shape when
dry.
• Bond tube, 3.5 in its position to accept mirror.
• Trim triangular moulding flush to underside of seat rear, 3.6, see
arrow.
• Bond former, 3.7 into seat rear, maintaining a 1.5 mm distance
from edge of seat (see illustration).
• Assemble seat rear to deck, adjust if necessary and bond using
supplied adhesive.
Part No. Description, size in mm number required
3.8 Press nut, M6 1
3.9 Spacer, 3 PP 1
3.10 Retainer plate, 3 PP 1
3.11 ixing plate, 3 PP 1
3.12 ormer middle, 3 PP 1
3.13 Longitudinal former, 3 PP 2
3.14 ormer rear, 3 PP 1
3.15 ormer front, 3 PP 1
3.16 Screw guide upper, 3 PP 2
3.17 Screw guide lower, 3 PP 1
3.18 Retaining bolt, M6 x 16 1
• Bond press nut, 3.8, spacer, 3.9 and retainer plate, 3.10 together.
• Locate and bond retainer plate sub assembly to its position on
the underside of the seat moulding on the deck.
Modellbau
Lindinger
GmbH
Alte-Post-Str.
14
A-4591
Molln
e-Mail:
[email protected] www.lindinger.at
