Robe XT Series Bedienungsanleitung

www.robe.cz

USER MANUAL

Dominator 1200

Intelligent Centerpiece

Table of contents

1. Introduction.................................................................................................................... 4

1.1 Safety instructions ..................................................................................................... .4

1.2 Operating instructions ................................................................................................ 4

2. In general ........................................................................................................................ 5

2.1 Features ................................................................................................................... .5

2.2 Description of components ........................................................................................ 5

2.3 Fitting the lamp .......................................................................................................... 6

3. Installation ...................................................................................................................... 6

3.1 General instructions ................................................................................................... 6

3.2 Connection to the mains .............................................................................................

3.3 DMX-512 connection .................................................................................................

3.4 Test sequence ............................................................................................................

3.5 Projector addressing ..................................................................................................

4. Operation ........................................................................................................................ 7

4.1 Reset .........................................................................................................................

4.2 Operation LED ...........................................................................................................

4.3 DMX protocol ............................................................................................................. 8

5 Maintenance and cleaning ............................................................................................. 9

6 Technical pecifications ................................................................................................ 9

7. Appendix ........................................................................................................................ 9

DOMINATOR 1200 XT

Caution !

Keep this device away from rain and moisture !

Unplug mains lead before opening the housing !

FOR YOUR OWN AFETY, PLEA E READ THI U ER MANUAL CAREFULLY

BEFORE YOU INITIAL TART-UP!

Every person involved with the installation, operation and maintenance of this device have to:

- be qualilfied

- follow the instructions of this manual

Caution !

Be careful with your operations.

Dangerous electric shock when touching the wires !

1. Introduction

Thank you for having chosen a DOMINATOR 1200 XT. You will see you have acquired a powerful and versatile

device.

Unpack your DOMINATOR 1200 XT.

Before you initial start-up, please make sure that there is no damage caused by transportation. Should there be

any, consult your dealer and do not use the device.

1.1 afety instructions

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure

a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written

in this user manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not

accept liability for any resulting defects or problems.

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on

immediately. The arising condensation water might damage your device. Leave the device switched off until it has

reached room temperature.

During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily

mean that the device is defective.

Please consider that damages caused by manual modifications to the device are not subject to warranty.

1.2 Operating instructions

This device was designed for indoor use only.

Do not shake the device. Avoid brute force when installing or operating the device.

You can install the device at any desired place. Please make sure that the device is not exposed to extreme heat,

moisture or dust. There should not be any cables lying around. You endanger your own and the safety of others!

Operate the device only after having familiarized with its functions. Do not allow an operation by persons who do

not know the device well enough. Most damages are the result of an unprofessional operation!

Please consider that for safety reasons unauthorized modifications to the device are forbidden!

When taking the device into operation, please make sure that the housing is closed firmly with all the necessary

screws tightened up.

2. In general

2.1 Features

6 - fold Multiscanner

- Intelligent centrepiece

- New! Now with additional cylinder-effect for even more change

- The rotation speed of the opposed cylinders is freely controllable

- New! Now with stepper-motors

- New! Now with rotating 3-fold prism-effect

- New! All in all 6 different gobos

- New! Multicolor-effect

- 2 effect-wheels (prism, gobos, colors), which can be mixed individually

- 3 different dichroic color filters (magenta, cyan, yellow)

- Programmable via every standard DMX-512 controller (12 channels)

- Black-Out

2.2 Description of components

1 - Mirror head

2 - Mirror

3 - Objective

4 - Fan

5 - Mirrored cylinder

6 - Fastening screw

7 - Top cover

8 - DMX-output

9 - DMX-input

10 - DIP-switches for projector selection

11 - Operating - LED



Internal view

1 - Mirror head

2 - Mirror

3 - Objective

5 - Mirrored cylinder

12 - lense holder

13 - Lamp holder

14 - Side cover

15 - Gobo holder

16 - Prism holder

2.3 Fitting the lamp

Caution !

Do not operate this device with opened service lid as continued

direct contact with discharge lamps can cause burned skin

because of ultraviolet radiation !

To insert the lamp (HMI 1200W) open the housing by loosening fastening screws at the top cover.

CAUTION: The lamp is very shock-sensitive!

Do not install a lamp with a higher wattage! A lamp like this generates temperatures the device is not designed for.

Damages caused by non-observance are not subject to warranty.

During the installation do not touch the glass-bulbs bare-handed! Please follow the lamp manufacturers notes!

Before you close the housing again, make sure that the lamp is installed tightly into the lampholder system.

Reclose the housing and tighten the fastenig screws.

Caution !

Do not operate this device with opened service lid

as continued direct contact with discharge lamps can

cause burned skin because of ultraviolet light !

3. Installation

3.1 General instructions

Danger of fire !

When installing the device, make sure there is no highly-inflammble

material (decoration articles, etc.) within a distance of min. 0,5m.

The projector can be installed in any postition without altering its operation characteristics.

Caution !

Make sure that the device is fixed properly ! Ensure that the structure

to which you are attaching the projector is secure !

For fixing the projector use the hole provided in the bracket. The hole in the adjustable mounting bracket has a

diameter of 8mm.

For overhead use, fit a safety chain or cord

3.2 Connection to the mains

Caution !

The electric connection has to be carried out by a qualified employee only !

Connect the projector with the mains plug to the mains

3.3 DMX-512 connection

Connect the controller with the projector using a stereo shielded cable and 3-pin XLR-connectors.

In order to connect the controller, you have to adjust the starting address of the DOMINATOR like shown under 3.5.

3.4 Test sequence

In order to run the test sequence, adjust the starting address of the DOMINATOR as follows:

3.5 Projector addressing

If the DOMINATOR is to be connected with a Universal DMX Controller , adjust the starting address of the

DOMINATOR as follows:

4. Operation

4.1 Reset

As soon as the projector is switched on, the motors are adjusted (Reset) and the device is ready for use within c.

10 seconds.

4.2 Operation LED

If the projector is connected with a controller via the DMX-input, but does not receive any data, the operation LED

is flashing.

Channel Value Function Type of control

1 Pan-movement mirrorhead 1and 4

0-255 Gradual pan mirror movement proportional

2 Tilt-movement mirrorhead 1and 4

0-255 Gradual tilt mirror movement proportional

3 Pan-movement mirrorhead 2and 5

0-255 Gradual pan mirror movement proportional

4 Tilt-movement mirrorhead 2and 5

0-255 Gradual tilt mirror movement proportional

5 Pan-movement mirrorhead 3and 6

0-255 Gradual pan mirror movement proportional

6 Tilt-movement mirrorhead 3and 6

0-255 Gradual tilt mirror movement proportional

7 Effect wheel 1

0- 9 Full circle,white step

80-159 Multicolour gobo step

160-239 6 gobos with 6 colours step

240-255 Rainbow effect step

8 Effect wheel 2

0 Blackout step

1-85 Dimmer intensity (85-max.intensity) step

86-124 Full circle,white step

125-12 Reset step

128-192 Magenta,cyan,yellow step

193-255 Rotating 3-fold prism step

9 Prism rotation

0-126 Anti-clokwise rotation with decreasing speed proportional

12 -128 No rotation step

129-255 Clokwise rotation with increasing speed proportional

10 Rotation of the mirrored cylinders between

mirrorhead 1/2 and 4/5

0 No rotation step

1-126 Anti-clokwise rotation with decreasing speed proportional

12 -128 No rotation step

129-254 Clokwise rotation with increasing speed proportional

255 No rotation step

11 Rotation of the mirrored cylinders between

mirrorhead 2/3 and 5/6

0 No rotation step

1-126 Anti-clokwise rotation with decreasing speed proportional

12 -128 No rotation step

129-254 Clokwise rotation with increasing speed proportional

255 No rotation step

4.3 DMX protocol

Channel Value Function Type of control

12 Rotation of the mirrored cylinders between

mirrorhead 3/4 and 6/1

0 No rotation step

1-126 Anti-clokwise rotation with decreasing speed proportional

12 -128 No rotation step

129-254 Clokwise rotation with increasing speed proportional

255 No rotation step

5 Maintenance and cleaning

Danger to life !

Disconnect from mains before starting maintenance operation !

It is absolutely essential that the projector is kept clean and that dust, dirt and smoke fluid residues must not build

up on or within the projector. If this happens, the light output from the projector will be significantly reduced.

Regular cleaning will not only ensure the maximum light output, but will also allow the projector to function reliably

throughout its life. A soft lint-free cloth moistened with any good glass cleaning fluid is recommended, under no

circumstances should alcohol or solvents be used!

The front mirror and objective lens will require monthly cleaning as smoke fluid tends to building up residues,

reducing the light output very quickly. The cooling fan should also be cleaned monthly.

The gobos may be cleaned with a soft brush.

The dichroic colour filters, the gobo-wheel and the internal lenses should be cleaned every three months.

The interior of the projector should be cleaned at least annually using a vacuum cleaner or air jet.

To ensure a proper function of the rotating gobos, we recommend lubrication in six month intervals. The

quantity of oil must not be excessive in order to avoid that oil run out when the gobo wheel rotates.

6 Technical pecifications

Power supply

Power supply: 208V / 60Hz (US Version) or 230V / 50Hz (EU Version)

Power consumption: 1500W

Fuse: T10A

Lamp

- HMI 1200W GS double-sided

Motor

- 21 microstepping stepper motors controlled by microprocessor

- 6 DC-motors

Electronics

- Digital serial input DMX-512

- 12 control channels

Housing

- Easy access to lamp and main components thanks to large opening cover

Dimensions and weight

- W x H x D: 1000 x 1000 x 500mm

- Weight: 48kg

7. Appendix

We hope you will enjoy your DOMINATOR 1200. We can assure you that you will enjoy this device for years if you

follow the instructions given in this manual.

Should you have further questions, do not hesitate to contact your local dealer..

Version 1.0

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Robe Beleuchtungsausrüstung Handbücher

Robe

Robe Robin T2 Bedienungsanleitung

Robe

Robe Colormix 240 AT Bedienungsanleitung

Robe

Robe Anolis ArcDot-US Bedienungsanleitung

Robe

Robe Robin 300E Spot Bedienungsanleitung

Robe

Robe T32 CYC Bedienungsanleitung

Robe

Robe Robin DL4F Wash Bedienungsanleitung

Robe

Robe Color Wash 700E AT Bedienungsanleitung

Robe

Robe PATT 2013 Bedienungsanleitung

Robe

Robe Robin T11 Profile Bedienungsanleitung

Robe

Robe ArcSource Outdoor 16 MC Integral RGBW US Bedienungsanleitung

Robe

Robe Color Wasf 1200E Bedienungsanleitung

Robe

Robe ClubWash 250CT Bedienungsanleitung

Robe

Robe Robin 600 Purewhite WIreless DMX Bedienungsanleitung

Robe

Robe Robin MMX Blade Bedienungsanleitung

Robe

Robe CLUBSPOT 160 CT Bedienungsanleitung

Robe

Robe Robin BMFL FollowSpot Bedienungsanleitung

Robe

Robe DT Series Bedienungsanleitung

Robe

Robe Anolis Calumma S MC Bedienungsanleitung

Robe

Robe ROBIN Pointe Bedienungsanleitung

Robe

Robe Anolis ArcSource Outdoor 48 MC Integral RGBW Bedienungsanleitung

Robe

Robe REDBLINDER 2-48 Bedienungsanleitung

Robe

Robe Robin 100 LEDBeam Wireless DMX CRMX Bedienungsanleitung

Robe

Robe Robin DL7S Profile Bedienungsanleitung

Robe

Robe Color Mix 250 AT Series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung