Roberts 10-91 Bedienungsanleitung

Multi-Floor Cutters

OWNER’S MANUAL

Coupeuse à planchers multiples

MANUEL D’UTILISATION

Cortador para múltiples pisos

MANUAL DE OPERACIÓN

WARNING Read and understand all instructions. Failure to follow all instructions may result in serious

bodily injury. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

AVERTISSEMENT Lire et comprendre toutes les directives. Le non-respect des directives peut causer des

blessures graves.VEUILLEZ CONSERVER CES DIRECTIVES POUR RÉFÉRENCE ULTÉRIEURE.

ADVERTENCIA Lea y comprenda todas las instrucciones. Si no se cumplen todas las instrucciones a puede

producir lesiones físicas graves. CONSERVE ESTAS INSTRUCCIONES PARA CONSULTARLAS EN EL FUTURO.

10-91

10-94

10-99

- 1 -

SAFETY RULES FOR THE MULTI-FLOOR CUTTER

WARNING! FAILURETO FOLLOWTHESE RULES MAY RESULT IN SERIOUS

INJURY! USINGTHIS MACHINE WITH RESPECT AND CAUTION WILL

CONSIDERABLY LESSENTHE POSSIBILITY OF PERSONAL INJURY.

1. READ AND UNDERSTANDTHIS INSTRUCTION MANUAL BEFORE OPERATING

THE MULTI-FLOOR CUTTER.

2. If you are not thoroughly familiar with the operation of the Multi-Floor Cutter,

obtain advice from a qualiﬁed instructor or call 866-435-8665

3. Stay alert. Do not operate while under the inﬂuence of drugs, alcohol,

or medication.

4. Always wear safety approved eye protection with side shields (ANSI Z87.1)

5. Keep work area and free of debris.

6. Keep children and unauthorized persons away from the Multi-Floor Cutter and

work area.

7. Make sure tool is secure. Operate only on a ﬁrm substrate or solid stand.

8. Use the right tool. Do not force the Multi-Floor Cutter or use it for a job for

which it was not designed; use only on approved materials.

9. Keep blade sharp. A dull blade will not perform properly.

10. Always keep hands away from blade while operating or carrying.

11. Do not alter or misuse this tool. The Multi-Floor Cutter is precision built;

modiﬁcations not speciﬁed in this manual may result in a dangerous condition.

12. Maintain the Multi-Floor Cutter with care. Keep blade sharp and clean. Follow

instructions for lubricating and changing accessories.

13. Use only recommended accessories. The use of improper accessories may

cause hazards or injury.

14. Never leave the Multi-Floor Cutter unattended. Secure the handle with the lock

chain when not in use.

15. Warning: The dust generated by cutting certain wood, wood ﬁber and / or PVC

products can be harmful to your health.

- 2 -

SET UP OFTHE CUTTER

Install the table to the cutter base with

provided screws and bolts

as shown.

Pull up the lock pin on the aluminum

handle as shown and insert the handle

into the handle base as shown.

Warning: Do not put your ﬁngers against

the sharp edge of the blade at any time.

CUTTING PREPARATION

Adjust the angle attachment to desired

angle as needed.

The angle attachment can be used on

left side of the table as shown.

Warning: Do not put your ﬁngers against

the sharp edge of the blade at any time.

STRAIGHT CUTTING

Insert material between the cutting

blade and the base, ﬂush it with the

guide bar as shown and hold the

material then push handle down to

complete a cut.

Warning: Maintain control of the handle.

Do not allow handle to slam back after

making a cut.

45° CUTTING

Adjust the angle attachment to 45°.

Insert material between the cutting

blade and the base, against the angle

attachment as shown, then push the

handle down to complete a cut.

Warning: Maintain control of the handle.

Do not allow handle to slam back after

making a cut.

Warning: Do not put your ﬁngers against

the sharp edge of the blade at any time.

SET UP

CUTTING

- 3 -

MAINTENANCE

CHANGINGTHE BLADE

Use Roberts #10-910 (9"), 10-940 (13”)

or 10-990 (18”) Replacement Blade. Use

the provided Allen wrench to remove

the screws, then hold the blade at each

end and carefully move the blade out of

blade holder.

Note: The ﬂat side of the blade should

face the table.

Warning: Do not put your ﬁngers against

the sharp edge of the blade at any time.

CHANGINGTHE NYLON BAR

Use the provided Allan wrench to

remove the screws, then hold the nylon

bar and carefully move it out of nylon

bar holder.

Warning: Do not put your ﬁngers against

the sharp edge of the blade at any time.

TRANSPORT

Insert the pin as shown to the hole in the

aluminum eccentric cam and carry the

cutter as shown.

- 4 -

ROBERTS 10-91 EXPLODED PARTS DIAGRAM

- 5 -

ROBERTS 10-91 PARTS LIST

NO. DESCRIPTION Q TY. NO. DESCRIPTION QTY.

1 Screw M6 × 12 4 25 Right ABS Handle 1

2 Washer Φ6 2 26 Bolt M4 × 30 2

3 Rubber Feet 6 27 Left ABS Handle 2

4 Rod 4 28 Guide Bar 1

5 Hex Bolt M8 × 55 1 29 Screw M5 × 8 8

6 Hex Bolt M8 × 50 1 30 Nut M10 4

7 Main Base 2 31 Sleeve 6

8 Screw M4 × 14 2 32 Nut M5 3

9 Nylon Bar 2 33 Working Table 3

10 Blade 2 34 Screw M5 ×12 3

11 Spring 2 35 Carry Handle 3

12 Screw M5 × 10 1 36 End Board 1

13 Blade Base 2 37 Foot 1

14 Screw M8 × 14 1 38 Bolt M8 × 30 4

15 Nut M12 1 39 Frame A 1

16 Nylon Wheel 2 40 Cross Bar 3

17 Aluminum Eccentric Cam 1 41 Frame B 1

18 Screw M6 × 16 1 42 Spring Pin 1

19 Handle Base 1 43 Nut M8 4

20 Bolt M12 × 120 2 44 Pin Sleeve 2

21 Handle A 1 45 Screw M4 × 10 4

22 Screw M8 2 46 Pin 2

23 Handle B 1 47 Shaft 2

24 Nut M4 1

- 6 -

ROBERTS 10-94 EXPLODED PARTS DIAGRAM

- 7 -

ROBERTS 10-94 PARTS LIST

NO. DESCRIPTION Q TY. NO. DESCRIPTION QTY.

1 Screw M6 × 12 4 25 Right ABS Handle 1

2 Washer Φ6 4 26 Bolt M4 × 30 2

3 Rubber Feet 4 27 Left ABS Handle 2

4 Rod 2 28 Guide Bar 1

5 Hex Bolt M8 × 55 4 29 Screw M5 × 8 9

6 Hex Bolt M8 × 50 4 30 Nut M10 4

7 Main Base 1 31 Sleeve 6

8 Screw M4 × 14 5 32 Nut M5 3

9 Nylon Bar 1 33 Working Table 3

10 Blade 1 34 Screw M5 ×12 3

11 Spring 1 35 Carry Handle 3

12 Screw M5 × 10 5 36 End Board 1

13 Blade Base 1 37 Foot 1

14 Screw M8 × 14 2 38 Bolt M8 × 30 4

15 Shaft 2 39 Frame A 1

16 Nut M12 1 40 Cross Bar 3

17 Nylon Wheel 2 41 Frame B 1

18 Aluminum Eccentric Cam 1 42 Sping Pin 1

19 Handle Base 1 43 Nut M8 4

20 Bolt M12 × 120 1 44 Pin Sleeve 2

21 Handle A 1 45 Screw M4 × 10 4

22 Screw M8 2 46 Pin 2

23 Handle B 1 47 Screw M6 × 16 4

24 Nut M4 2

- 8 -

ROBERTS 10-99 EXPLODED PARTS DIAGRAM

- 9 -

ROBERTS 10-99 PARTS LIST

NO. DESCRIPTION Q TY. NO. DESCRIPTION QTY.

1 Screw M6 × 12 4 25 Right ABS Handle 1

2 Washer Φ6 4 26 Bolt M4 × 30 2

3 Rubber Feet 4 27 Left ABS Handle 1

4 Rod 2 28 Guide Bar 1

5 Hex Bolt M8 × 55 4 29 Screw M5 × 8 13

6 Hex Bolt M8 × 50 4 30 Nut M10 8

7 Main Base 1 31 Sleeve 8

8 Screw M4 × 14 7 32 Nut M5 3

9 Nylon Bar 1 33 Working Table 1

10 Blade 1 34 Screw M5 ×12 3

11 Spring 1 35 Carry Handle 1

12 Screw M5 × 10 7 36 End Board 1

13 Blade Base 1 37 Foot 2

14 Screw M8 × 14 2 38 Bolt M8 × 30 4

15 Shaft 2 39 Frame A 1

16 Nut M12 1 40 Nut M8 4

17 Nylon Wheel 4 41 Cross Bar 3

18 Aluminum Eccentric Cam 1 42 Spring Pin 1

19 Handle Base 1 43 Frame B 1

20 Bolt M12 × 120 1 44 Pin Sleeve 2

21 Handle A 1 45 Screw M4 × 10 4

22 Screw M8 2 46 Pin 2

23 Handle B 1 47 Screw M6 × 16 4

24 Nut M4 2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Roberts Cutter Handbücher

Roberts

Roberts 10-95 Bedienungsanleitung

Roberts

Roberts 13 PRO Bedienungsanleitung

Roberts

Roberts 10-146 Bedienungsanleitung

Roberts

Roberts 10-66 Bedienungsanleitung

Roberts

Roberts 10-152 Bedienungsanleitung

Roberts

Roberts 10-60 Bedienungsanleitung

Roberts

Roberts 10-900 Bedienungsanleitung

Roberts

Roberts 10-60 Bedienungsanleitung

Roberts

Roberts 10-68 Bedienungsanleitung

Roberts

Roberts 10-63 Bedienungsanleitung

Roberts

Roberts 10-35 Bedienungsanleitung

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung

RODCRAFT

RODCRAFT RC7170 Bedienungsanleitung